Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- RaceTCS V3
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- RaceTCS
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
RaceTCS V3 connector positions from the version 1.04 manual, page 9. Numbers denote rows and letters columns as drawn by the maker; letters skip I. Both early and later diagrams show these functions but differ in displayed colours, so identify cavities rather than relying on wire colours. This is not the V2 pinout.
Injector/coil inputs and outputs refer to the selected fuel-cut or spark-cut configuration; check the applicable operating mode and manufacturer requirements.
PinFunction1A, 1B, 2A, 2BGround1L, 1MPower ground4L, 4MSwitched ignition +12 V4A, 4B+5 V output3APreset potentiometer input3BUSB ground3CUSB D−3DUSB D+3EUSB Vbus3GFront left wheel-speed input3HFront right wheel-speed input3JRear left wheel-speed input3KRear right wheel-speed input4HClutch input4JLED output4K0–5 V output1CInjector/coil output 81DInjector/coil output 71EInjector/coil output 61FInjector/coil output 51GInjector/coil output 41HInjector/coil output 31JInjector/coil output 21KInjector/coil output 12CInjector/coil input 82DInjector/coil input 72EInjector/coil input 62FInjector/coil input 52GInjector/coil input 42HInjector/coil input 32JInjector/coil input 22KInjector/coil input 1
Source: RaceTCS V3 user manual. Confirm orientation, actual harness revision, vehicle-specific wiring and compatibility against the manufacturer’s drawing before installation.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: RaceTCS V3 connector pinout
RaceTCS V3 connector positions from the version 1.04 manual, page 9. Numbers denote rows and letters columns as drawn by the maker; letters skip I. Both early and later diagrams show these functions but differ in displayed colours, so identify cavities rather than relying on wire colours. This is not the V2 pinout.
Injector/coil inputs and outputs refer to the selected fuel-cut or spark-cut configuration; check the applicable operating mode and manufacturer requirements.
| Pin | Function |
|---|
| 1A, 1B, 2A, 2B | Ground |
| 1L, 1M | Power ground |
| 4L, 4M | Switched ignition +12 V |
| 4A, 4B | +5 V output |
| 3A | Preset potentiometer input |
| 3B | USB ground |
| 3C | USB D− |
| 3D | USB D+ |
| 3E | USB Vbus |
| 3G | Front left wheel-speed input |
| 3H | Front right wheel-speed input |
| 3J | Rear left wheel-speed input |
| 3K | Rear right wheel-speed input |
| 4H | Clutch input |
| 4J | LED output |
| 4K | 0–5 V output |
| 1C | Injector/coil output 8 |
| 1D | Injector/coil output 7 |
| 1E | Injector/coil output 6 |
| 1F | Injector/coil output 5 |
| 1G | Injector/coil output 4 |
| 1H | Injector/coil output 3 |
| 1J | Injector/coil output 2 |
| 1K | Injector/coil output 1 |
| 2C | Injector/coil input 8 |
| 2D | Injector/coil input 7 |
| 2E | Injector/coil input 6 |
| 2F | Injector/coil input 5 |
| 2G | Injector/coil input 4 |
| 2H | Injector/coil input 3 |
| 2J | Injector/coil input 2 |
| 2K | Injector/coil input 1 |
Source: RaceTCS V3 user manual. Confirm orientation, actual harness revision, vehicle-specific wiring and compatibility against the manufacturer’s drawing before installation.
Revision 1: RaceTCS V3 connector pinout
RaceTCS V3 connector positions from the version 1.04 manual, page 9. Numbers denote rows and letters columns as drawn by the maker; letters skip I. Both early and later diagrams show these functions but differ in displayed colours, so identify cavities rather than relying on wire colours. This is not the V2 pinout.
Injector/coil inputs and outputs refer to the selected fuel-cut or spark-cut configuration; check the applicable operating mode and manufacturer requirements.
| Pin | Function |
|---|
| 1A, 1B, 2A, 2B | Ground |
| 1L, 1M | Power ground |
| 4L, 4M | Switched ignition +12 V |
| 4A, 4B | +5 V output |
| 3A | Preset potentiometer input |
| 3B | USB ground |
| 3C | USB D− |
| 3D | USB D+ |
| 3E | USB Vbus |
| 3G | Front left wheel-speed input |
| 3H | Front right wheel-speed input |
| 3J | Rear left wheel-speed input |
| 3K | Rear right wheel-speed input |
| 4H | Clutch input |
| 4J | LED output |
| 4K | 0–5 V output |
| 1C | Injector/coil output 8 |
| 1D | Injector/coil output 7 |
| 1E | Injector/coil output 6 |
| 1F | Injector/coil output 5 |
| 1G | Injector/coil output 4 |
| 1H | Injector/coil output 3 |
| 1J | Injector/coil output 2 |
| 1K | Injector/coil output 1 |
| 2C | Injector/coil input 8 |
| 2D | Injector/coil input 7 |
| 2E | Injector/coil input 6 |
| 2F | Injector/coil input 5 |
| 2G | Injector/coil input 4 |
| 2H | Injector/coil input 3 |
| 2J | Injector/coil input 2 |
| 2K | Injector/coil input 1 |
Source: RaceTCS V3 user manual. Confirm orientation, actual harness revision, vehicle-specific wiring and compatibility against the manufacturer’s drawing before installation.