Removed text is struck through; added text is highlighted.
MultiMode or M-MT identifies a Toyota automated manual transmission in the examples below. The clutch and gear changes are actuated electronically rather than by a clutch pedal. Toyota's AYGO introduction describes electric-motor actuation with automatic E and driver-requested sequential M modes; its Yaris material describes E, Es and M modes on that documented generation. These examples do not establish identical operation for every Toyota labelled MultiMode. Toyota AYGO press kit, p. 48; Toyota Yaris press kit, p. 50.
Identify the transmission and the event
Record the model, engine, build date, gearbox and transmission ECU, software, warning, selector mode and service history. Do not assume Toyota MultiMode is the same transmission as a Multidrive CVT, conventional automatic or later dual-clutch unit. When investigating a complaint, distinguish start refusal, no selected gear, unexpected neutral, shift interruption, clutch slip and a temperature warning.
Clutch warning example: AYGO
In the AYGO handbook identified as OM99L81E, a steady Multi-mode transmission warning signals a system malfunction. Its warning-and-buzzer indications distinguish a system malfunction with an overheated clutch from a flashing hot-clutch warning that the manual says does not by itself indicate a transmission-system fault. For those stated indications, Toyota tells the driver to stop safely, select N and wait approximately 15 minutes for cooling; the malfunction-and-overheat indication also calls for the system to be checked. Use the exact car's handbook: lamp meanings, prerequisites and actions may differ. Toyota AYGO owner's manual, warning lights.
Diagnosis and recorded data
Preserve transmission and engine fault codes, status and available freeze-frame data before clearing memory or performing learning. Record the event, brake and selector inputs, operating mode and temperature.
Using the correct diagnostic tool and wiring information, compare request with clutch, gear selection and engagement feedback, engine and transmission speed, supply voltage and relevant communication or interlock states where available. A symptom or actuator-circuit code alone does not prove a replacement actuator is needed.
Inspect the clutch and release mechanism, actuator and position sensing, wiring, power supply and gear-selection system according to the fault-specific service procedure. A learning failure may reflect a physical or electrical fault rather than a need for repeated resets.
5MMT P0810, judder and repair history
Toyota Motor Europe's 2012 5MMT bulletin describes either no creep or clutch judder, an MMT warning with P0810, or both, on specified Auris, Corolla, Corolla Verso and Yaris model codes. These symptoms do not by themselves identify a failed actuator. Match the model code, production range, symptom and current Toyota repair information before selecting the diagnostic branch. Toyota TSB CP-0006T-0112.
In its 5MMT repair guidance for specified Auris, AYGO, Corolla, Corolla Verso and Yaris models, Toyota warns that initializing the MMT ECU without replacing parts can leave clutch learning values inconsistent with the self-adjusting clutch cover and may trigger P0810. It also stresses the correct adjustment and actuator installation sequence. Record previous resets and repairs, and use the current vehicle-specific Toyota procedure rather than treating initialization as a generic cure. Toyota TSB CP-0009T-0113.
6MMT P0900: clutch actuator motor contamination
Toyota Motor Europe bulletin CP-0022T-0411, revised July 2014, addresses P0900 with the MMT warning on specified six-speed MMT Auris, Corolla, Verso-S and Yaris model codes produced before the listed production-change VINs. It describes an actuator-motor short associated with carbon brush powder mixing with bearing grease and a production change adding a brush cover. The bulletin distinguishes cases by motor-resistance testing and directs its own repair path. P0900 has other possible causes: verify the gearbox, model code, VIN, exact fault and current Toyota guidance before attributing it to this condition or attempting repair. This six-speed example does not establish the same fault or remedy for the five-speed AYGO and Corolla Verso cases above. The hosted bulletin may require access; an alternative reproduction is available.
Toyota’s MMT diagnosis summary CP-0081T-0815 separately cautions that an incorrect clutch-actuator hydraulic bleeding sequence on the six-speed MMT it covers can result in P0810 or clutch slip after clutch-system work. Record recent work and use the exact vehicle’s current bleeding and initialization instructions; this is a repair-history lead, not proof of trapped air or a procedure to apply to the five-speed mechanism. The reproduced bulletin may require access.
Initialization depends on the repair
Toyota service bulletin CP-4014, October 2004, for its stated European Corolla Verso application, distinguishes ECU, clutch and transmission initialization according to the parts repaired. It says calibration values and DTC history in the MMT ECU are not cleared simply by disconnecting the battery. It also identifies selector-position, engine-speed signal and CAN issues as possible avenues when initialization cannot be completed. These are bulletin-specific observations, not instructions to initialize every MMT.
Initialization can erase useful learned or fault information and may cause actuators to move. Follow the current repair procedure, diagnostic equipment and prerequisites for the exact vehicle and component work; do not copy a Corolla Verso sequence to AYGO or Yaris. A reset does not repair a worn clutch, wiring fault or mechanical problem.
See automated manual clutch and gearshift control, clutch operation and types and the gearbox catalogue.
Open each version to inspect formatting, tables and photographs.
Revision 4: Toyota MultiMode MMT automated manual operation and diagnosis
MultiMode or M-MT identifies a Toyota automated manual transmission in the examples below. The clutch and gear changes are actuated electronically rather than by a clutch pedal. Toyota's AYGO introduction describes electric-motor actuation with automatic E and driver-requested sequential M modes; its Yaris material describes E, Es and M modes on that documented generation. These examples do not establish identical operation for every Toyota labelled MultiMode. Toyota AYGO press kit, p. 48; Toyota Yaris press kit, p. 50.
Identify the transmission and the event
Record the model, engine, build date, gearbox and transmission ECU, software, warning, selector mode and service history. Do not assume Toyota MultiMode is the same transmission as a Multidrive CVT, conventional automatic or later dual-clutch unit. When investigating a complaint, distinguish start refusal, no selected gear, unexpected neutral, shift interruption, clutch slip and a temperature warning.
Clutch warning example: AYGO
In the AYGO handbook identified as OM99L81E, a steady Multi-mode transmission warning signals a system malfunction. Its warning-and-buzzer indications distinguish a system malfunction with an overheated clutch from a flashing hot-clutch warning that the manual says does not by itself indicate a transmission-system fault. For those stated indications, Toyota tells the driver to stop safely, select N and wait approximately 15 minutes for cooling; the malfunction-and-overheat indication also calls for the system to be checked. Use the exact car's handbook: lamp meanings, prerequisites and actions may differ. Toyota AYGO owner's manual, warning lights.
Diagnosis and recorded data
- Preserve transmission and engine fault codes, status and available freeze-frame data before clearing memory or performing learning. Record the event, brake and selector inputs, operating mode and temperature.
- Using the correct diagnostic tool and wiring information, compare request with clutch, gear selection and engagement feedback, engine and transmission speed, supply voltage and relevant communication or interlock states where available. A symptom or actuator-circuit code alone does not prove a replacement actuator is needed.
- Inspect the clutch and release mechanism, actuator and position sensing, wiring, power supply and gear-selection system according to the fault-specific service procedure. A learning failure may reflect a physical or electrical fault rather than a need for repeated resets.
5MMT P0810, judder and repair history
Toyota Motor Europe's 2012 5MMT bulletin describes either no creep or clutch judder, an MMT warning with P0810, or both, on specified Auris, Corolla, Corolla Verso and Yaris model codes. These symptoms do not by themselves identify a failed actuator. Match the model code, production range, symptom and current Toyota repair information before selecting the diagnostic branch. Toyota TSB CP-0006T-0112.
In its 5MMT repair guidance for specified Auris, AYGO, Corolla, Corolla Verso and Yaris models, Toyota warns that initializing the MMT ECU without replacing parts can leave clutch learning values inconsistent with the self-adjusting clutch cover and may trigger P0810. It also stresses the correct adjustment and actuator installation sequence. Record previous resets and repairs, and use the current vehicle-specific Toyota procedure rather than treating initialization as a generic cure. Toyota TSB CP-0009T-0113.
6MMT P0900: clutch actuator motor contamination
Toyota Motor Europe bulletin CP-0022T-0411, revised July 2014, addresses P0900 with the MMT warning on specified six-speed MMT Auris, Corolla, Verso-S and Yaris model codes produced before the listed production-change VINs. It describes an actuator-motor short associated with carbon brush powder mixing with bearing grease and a production change adding a brush cover. The bulletin distinguishes cases by motor-resistance testing and directs its own repair path. P0900 has other possible causes: verify the gearbox, model code, VIN, exact fault and current Toyota guidance before attributing it to this condition or attempting repair. This six-speed example does not establish the same fault or remedy for the five-speed AYGO and Corolla Verso cases above. The hosted bulletin may require access; an alternative reproduction is available.
Toyota’s MMT diagnosis summary CP-0081T-0815 separately cautions that an incorrect clutch-actuator hydraulic bleeding sequence on the six-speed MMT it covers can result in P0810 or clutch slip after clutch-system work. Record recent work and use the exact vehicle’s current bleeding and initialization instructions; this is a repair-history lead, not proof of trapped air or a procedure to apply to the five-speed mechanism. The reproduced bulletin may require access.
Initialization depends on the repair
Toyota service bulletin CP-4014, October 2004, for its stated European Corolla Verso application, distinguishes ECU, clutch and transmission initialization according to the parts repaired. It says calibration values and DTC history in the MMT ECU are not cleared simply by disconnecting the battery. It also identifies selector-position, engine-speed signal and CAN issues as possible avenues when initialization cannot be completed. These are bulletin-specific observations, not instructions to initialize every MMT.
Initialization can erase useful learned or fault information and may cause actuators to move. Follow the current repair procedure, diagnostic equipment and prerequisites for the exact vehicle and component work; do not copy a Corolla Verso sequence to AYGO or Yaris. A reset does not repair a worn clutch, wiring fault or mechanical problem.
See automated manual clutch and gearshift control, clutch operation and types and the gearbox catalogue.
Revision 4: Toyota MultiMode MMT automated manual operation and diagnosis
MultiMode or M-MT identifies a Toyota automated manual transmission in the examples below. The clutch and gear changes are actuated electronically rather than by a clutch pedal. Toyota's AYGO introduction describes electric-motor actuation with automatic E and driver-requested sequential M modes; its Yaris material describes E, Es and M modes on that documented generation. These examples do not establish identical operation for every Toyota labelled MultiMode. Toyota AYGO press kit, p. 48; Toyota Yaris press kit, p. 50.
Identify the transmission and the event
Record the model, engine, build date, gearbox and transmission ECU, software, warning, selector mode and service history. Do not assume Toyota MultiMode is the same transmission as a Multidrive CVT, conventional automatic or later dual-clutch unit. When investigating a complaint, distinguish start refusal, no selected gear, unexpected neutral, shift interruption, clutch slip and a temperature warning.
Clutch warning example: AYGO
In the AYGO handbook identified as OM99L81E, a steady Multi-mode transmission warning signals a system malfunction. Its warning-and-buzzer indications distinguish a system malfunction with an overheated clutch from a flashing hot-clutch warning that the manual says does not by itself indicate a transmission-system fault. For those stated indications, Toyota tells the driver to stop safely, select N and wait approximately 15 minutes for cooling; the malfunction-and-overheat indication also calls for the system to be checked. Use the exact car's handbook: lamp meanings, prerequisites and actions may differ. Toyota AYGO owner's manual, warning lights.
Diagnosis and recorded data
- Preserve transmission and engine fault codes, status and available freeze-frame data before clearing memory or performing learning. Record the event, brake and selector inputs, operating mode and temperature.
- Using the correct diagnostic tool and wiring information, compare request with clutch, gear selection and engagement feedback, engine and transmission speed, supply voltage and relevant communication or interlock states where available. A symptom or actuator-circuit code alone does not prove a replacement actuator is needed.
- Inspect the clutch and release mechanism, actuator and position sensing, wiring, power supply and gear-selection system according to the fault-specific service procedure. A learning failure may reflect a physical or electrical fault rather than a need for repeated resets.
5MMT P0810, judder and repair history
Toyota Motor Europe's 2012 5MMT bulletin describes either no creep or clutch judder, an MMT warning with P0810, or both, on specified Auris, Corolla, Corolla Verso and Yaris model codes. These symptoms do not by themselves identify a failed actuator. Match the model code, production range, symptom and current Toyota repair information before selecting the diagnostic branch. Toyota TSB CP-0006T-0112.
In its 5MMT repair guidance for specified Auris, AYGO, Corolla, Corolla Verso and Yaris models, Toyota warns that initializing the MMT ECU without replacing parts can leave clutch learning values inconsistent with the self-adjusting clutch cover and may trigger P0810. It also stresses the correct adjustment and actuator installation sequence. Record previous resets and repairs, and use the current vehicle-specific Toyota procedure rather than treating initialization as a generic cure. Toyota TSB CP-0009T-0113.
6MMT P0900: clutch actuator motor contamination
Toyota Motor Europe bulletin CP-0022T-0411, revised July 2014, addresses P0900 with the MMT warning on specified six-speed MMT Auris, Corolla, Verso-S and Yaris model codes produced before the listed production-change VINs. It describes an actuator-motor short associated with carbon brush powder mixing with bearing grease and a production change adding a brush cover. The bulletin distinguishes cases by motor-resistance testing and directs its own repair path. P0900 has other possible causes: verify the gearbox, model code, VIN, exact fault and current Toyota guidance before attributing it to this condition or attempting repair. This six-speed example does not establish the same fault or remedy for the five-speed AYGO and Corolla Verso cases above. The hosted bulletin may require access; an alternative reproduction is available.
Toyota’s MMT diagnosis summary CP-0081T-0815 separately cautions that an incorrect clutch-actuator hydraulic bleeding sequence on the six-speed MMT it covers can result in P0810 or clutch slip after clutch-system work. Record recent work and use the exact vehicle’s current bleeding and initialization instructions; this is a repair-history lead, not proof of trapped air or a procedure to apply to the five-speed mechanism. The reproduced bulletin may require access.
Initialization depends on the repair
Toyota service bulletin CP-4014, October 2004, for its stated European Corolla Verso application, distinguishes ECU, clutch and transmission initialization according to the parts repaired. It says calibration values and DTC history in the MMT ECU are not cleared simply by disconnecting the battery. It also identifies selector-position, engine-speed signal and CAN issues as possible avenues when initialization cannot be completed. These are bulletin-specific observations, not instructions to initialize every MMT.
Initialization can erase useful learned or fault information and may cause actuators to move. Follow the current repair procedure, diagnostic equipment and prerequisites for the exact vehicle and component work; do not copy a Corolla Verso sequence to AYGO or Yaris. A reset does not repair a worn clutch, wiring fault or mechanical problem.
See automated manual clutch and gearshift control, clutch operation and types and the gearbox catalogue.