Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Datalogging and telematics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
MoTeC

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

MoTeC L120 USB (MoTeC part #18045) is an enclosed motorsport data logger without an integrated driver display. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

MoTeC L120 USB. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.

Specifications and options

Enclosed logger without an integrated display; #18045 includes 120 MB internal recording and USB logging.Two configurable CAN buses and RS232; analogue voltage, temperature and auxiliary functions require the I/O upgrade.Manufacturer specifies rates up to 500 samples per second, 6–32 V DC operation and a three-axis accelerometer; T2 telemetry requires an upgrade and a separate link.

Connector and pinout

34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18045. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.

PinNameStandard functionOptional function1E-TX–Ethernet Transmit –2E-TX+Ethernet Transmit +3AV1Analogue Voltage Input 14AV2Analogue Voltage Input 25AV3Analogue Voltage Input 36AV4Analogue Voltage Input 478VSensor 8 V85VSensor 5 V90VSensor 0 V10E-RX–Ethernet Receive –11E-RX+Ethernet Receive +12AV5Analogue Voltage Input 513AV6Analogue Voltage Input 614DIG1Digital Input 115DIG2Digital Input 216AT1Analogue Temp Input 117AT2Analogue Temp Input 218CAN1LCAN1 Lo19CAN1HCAN1 Hi20RS232-1 TXRS232-1 Transmit Output21SPD1Speed Input 122SPD2Speed Input 223SPD3Speed Input 324Not usedNot used25RS232-2 RXRS232-2 Receive Input26CAN2LCAN2 Lo / RS232 Ground Input27CAN2HCAN2 Hi / RS232 Receive Input28RS232-1 RXRS232-1 Receive Input29AUX1Auxiliary Output 130AUX2Auxiliary Output 231AUX3Auxiliary Output 332AUX4Auxiliary Output 433BAT+Battery Positive34BAT–Battery Negative

Wiring and configuration

Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.

Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.

MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.

Data analysis softwareMoTeC i2 data analysis showing channel traces and gauges. Image: MoTeC, reproduced with permission; manufacturer image.The L120 USB records data for later analysis; the exact memory, logging and Pro Analysis options depend on the unit and licence. MoTeC i2 reviews recorded channels in graphs and reports; i2 Pro features depend on the device upgrade or applicable software licence. See the manufacturer model and analysis comparison and i2 software and licence information.Retrieve a recording with the compatible MoTeC device manager, then open it in i2 to compare channels and laps when suitable position data has been recorded. Download MoTeC software from the official downloads library; see the MoTeC manufacturer guide for the Standard and Pro options.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: MoTeC L120 USB

MoTeC L120 USB (MoTeC part #18045) is an enclosed motorsport data logger without an integrated driver display. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

MoTeC L120 USB product photograph
MoTeC L120 USB. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.

Specifications and options

  • Enclosed logger without an integrated display; #18045 includes 120 MB internal recording and USB logging.
  • Two configurable CAN buses and RS232; analogue voltage, temperature and auxiliary functions require the I/O upgrade.
  • Manufacturer specifies rates up to 500 samples per second, 6–32 V DC operation and a three-axis accelerometer; T2 telemetry requires an upgrade and a separate link.

Connector and pinout

34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18045. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.

PinNameStandard functionOptional function
1E-TX–Ethernet Transmit –
2E-TX+Ethernet Transmit +
3AV1Analogue Voltage Input 1
4AV2Analogue Voltage Input 2
5AV3Analogue Voltage Input 3
6AV4Analogue Voltage Input 4
78VSensor 8 V
85VSensor 5 V
90VSensor 0 V
10E-RX–Ethernet Receive –
11E-RX+Ethernet Receive +
12AV5Analogue Voltage Input 5
13AV6Analogue Voltage Input 6
14DIG1Digital Input 1
15DIG2Digital Input 2
16AT1Analogue Temp Input 1
17AT2Analogue Temp Input 2
18CAN1LCAN1 Lo
19CAN1HCAN1 Hi
20RS232-1 TXRS232-1 Transmit Output
21SPD1Speed Input 1
22SPD2Speed Input 2
23SPD3Speed Input 3
24Not usedNot used
25RS232-2 RXRS232-2 Receive Input
26CAN2LCAN2 Lo / RS232 Ground Input
27CAN2HCAN2 Hi / RS232 Receive Input
28RS232-1 RXRS232-1 Receive Input
29AUX1Auxiliary Output 1
30AUX2Auxiliary Output 2
31AUX3Auxiliary Output 3
32AUX4Auxiliary Output 4
33BAT+Battery Positive
34BAT–Battery Negative

Wiring and configuration

MoTeC L120 USB simplified power and CAN wiring
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.

Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.

MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.

Revision 2: MoTeC L120 USB

MoTeC L120 USB (MoTeC part #18045) is an enclosed motorsport data logger without an integrated driver display. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

MoTeC L120 USB product photograph
MoTeC L120 USB. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.

Specifications and options

  • Enclosed logger without an integrated display; #18045 includes 120 MB internal recording and USB logging.
  • Two configurable CAN buses and RS232; analogue voltage, temperature and auxiliary functions require the I/O upgrade.
  • Manufacturer specifies rates up to 500 samples per second, 6–32 V DC operation and a three-axis accelerometer; T2 telemetry requires an upgrade and a separate link.

Connector and pinout

34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18045. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.

PinNameStandard functionOptional function
1E-TX–Ethernet Transmit –
2E-TX+Ethernet Transmit +
3AV1Analogue Voltage Input 1
4AV2Analogue Voltage Input 2
5AV3Analogue Voltage Input 3
6AV4Analogue Voltage Input 4
78VSensor 8 V
85VSensor 5 V
90VSensor 0 V
10E-RX–Ethernet Receive –
11E-RX+Ethernet Receive +
12AV5Analogue Voltage Input 5
13AV6Analogue Voltage Input 6
14DIG1Digital Input 1
15DIG2Digital Input 2
16AT1Analogue Temp Input 1
17AT2Analogue Temp Input 2
18CAN1LCAN1 Lo
19CAN1HCAN1 Hi
20RS232-1 TXRS232-1 Transmit Output
21SPD1Speed Input 1
22SPD2Speed Input 2
23SPD3Speed Input 3
24Not usedNot used
25RS232-2 RXRS232-2 Receive Input
26CAN2LCAN2 Lo / RS232 Ground Input
27CAN2HCAN2 Hi / RS232 Receive Input
28RS232-1 RXRS232-1 Receive Input
29AUX1Auxiliary Output 1
30AUX2Auxiliary Output 2
31AUX3Auxiliary Output 3
32AUX4Auxiliary Output 4
33BAT+Battery Positive
34BAT–Battery Negative

Wiring and configuration

MoTeC L120 USB simplified power and CAN wiring
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.

Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.

MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.

Data analysis software

MoTeC i2 data analysis with channel traces and gauges
MoTeC i2 data analysis showing channel traces and gauges. Image: MoTeC, reproduced with permission; manufacturer image.

The L120 USB records data for later analysis; the exact memory, logging and Pro Analysis options depend on the unit and licence. MoTeC i2 reviews recorded channels in graphs and reports; i2 Pro features depend on the device upgrade or applicable software licence. See the manufacturer model and analysis comparison and i2 software and licence information.

Retrieve a recording with the compatible MoTeC device manager, then open it in i2 to compare channels and laps when suitable position data has been recorded. Download MoTeC software from the official downloads library; see the MoTeC manufacturer guide for the Standard and Pro options.