Removed text is struck through; added text is highlighted.
MoTeC C127 (MoTeC part #18069) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.
MoTeC C127. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.
Specifications and options
7-inch colour TFT display, 800 × 480 pixels; configurable channels, alarms and display layouts.Internal logging is an upgrade: 120 MB and rates up to 500 samples per second; USB logging is a further option. Confirm logging is enabled on the unit or included in the purchased kit.Two configurable CAN buses; two RS232 ports. Two digital and three speed inputs are listed. Six analogue voltage inputs, two temperature inputs and four low-side outputs require the I/O upgrade.Manufacturer lists 6–32 V DC operation, three-axis accelerometer and optional T2 telemetry; i2 analysis, GPS timing and connected sensors depend on the installation and options.
MoTeC identifies a previous part #18048; dimensions or construction may differ. Use the document for the unit in hand.
Connector and pinout
34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18069. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.
MoTeC's current #18069 product listing gives pin 24 as video input. Older C127 documentation differs; the manufacturer page and manual also differ in the label for pin 32. Verify the exact revision and intended function before connecting video or LIN.
* MoTeC lists live display of the composite video input as requiring the Display Creator upgrade on this C127. Confirm the exact part and revision. MoTeC product specification.
Wiring and configuration
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.
Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.
MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.
Data analysis softwareMoTeC i2 data analysis showing channel traces and gauges. Image: MoTeC, reproduced with permission; manufacturer image.The C127 needs its applicable data-logging upgrade or a logging-equipped kit before it can produce recordings for analysis. MoTeC i2 reviews recorded channels in graphs and reports; i2 Pro features depend on the device upgrade or applicable software licence. See the manufacturer model and analysis comparison and i2 software and licence information.Retrieve a recording with the compatible MoTeC device manager, then open it in i2 to compare channels and laps when suitable position data has been recorded. Download MoTeC software from the official downloads library; see the MoTeC manufacturer guide for the Standard and Pro options.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: MoTeC C127
MoTeC C127 (MoTeC part #18069) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.
Internal logging is an upgrade: 120 MB and rates up to 500 samples per second; USB logging is a further option. Confirm logging is enabled on the unit or included in the purchased kit.
Two configurable CAN buses; two RS232 ports. Two digital and three speed inputs are listed. Six analogue voltage inputs, two temperature inputs and four low-side outputs require the I/O upgrade.
Manufacturer lists 6–32 V DC operation, three-axis accelerometer and optional T2 telemetry; i2 analysis, GPS timing and connected sensors depend on the installation and options.
MoTeC identifies a previous part #18048; dimensions or construction may differ. Use the document for the unit in hand.
Connector and pinout
34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18069. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.
MoTeC's current #18069 product listing gives pin 24 as video input. Older C127 documentation differs; the manufacturer page and manual also differ in the label for pin 32. Verify the exact revision and intended function before connecting video or LIN.
Pin
Name
Function
1
E-TX–
Ethernet Transmit –
2
E-TX+
Ethernet Transmit +
3
AV1
Analogue Voltage Input 1 (with I/O upgrade)
4
AV2
Analogue Voltage Input 2 (with I/O upgrade)
5
AV3
Analogue Voltage Input 3 (with I/O upgrade)
6
AV4
Analogue Voltage Input 4 (with I/O upgrade)
7
8V
Sensor 8 V
8
5V
Sensor 5 V
9
0V
Sensor 0 V
10
E-RX–
Ethernet Receive –
11
E-RX+
Ethernet Receive +
12
AV5
Analogue Voltage Input 5 (with I/O upgrade)
13
AV6
Analogue Voltage Input 6 (with I/O upgrade)
14
DIG1
Digital Input 1
15
DIG2
Digital Input 2
16
AT1
Analogue Temp Input 1 (with I/O upgrade)
17
AT2
Analogue Temp Input 2 (with I/O upgrade)
18
CAN1L
CAN1 Lo
19
CAN1H
CAN1 Hi
20
RS232-1 TX
RS232-1 Transmit
21
SPD1
Speed Input 1
22
SPD2
Speed Input 2
23
SPD3
Speed Input 3
24
VID1
Video Input 1 *
25
RS232-2 RX
RS232-2 Receive
26
CAN2L
CAN2 Lo/RS232 Ground Input
27
CAN2H
CAN2 Hi/RS232 Receive
28
RS232-1 RX
RS232-1 Receive Input
29
AUX1
Auxiliary Output 1 (with I/O upgrade)
30
AUX2
Auxiliary Output 2 (with I/O upgrade)
31
AUX3
Auxiliary Output 3 (with I/O upgrade)
32
AUX4
Auxiliary Output 4 (with I/O upgrade)
33
BAT+
Battery Positive
34
BAT–
Battery Negative
Wiring and configuration
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.
Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.
MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.
Revision 3: MoTeC C127
MoTeC C127 (MoTeC part #18069) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.
Internal logging is an upgrade: 120 MB and rates up to 500 samples per second; USB logging is a further option. Confirm logging is enabled on the unit or included in the purchased kit.
Two configurable CAN buses; two RS232 ports. Two digital and three speed inputs are listed. Six analogue voltage inputs, two temperature inputs and four low-side outputs require the I/O upgrade.
Manufacturer lists 6–32 V DC operation, three-axis accelerometer and optional T2 telemetry; i2 analysis, GPS timing and connected sensors depend on the installation and options.
MoTeC identifies a previous part #18048; dimensions or construction may differ. Use the document for the unit in hand.
Connector and pinout
34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18069. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.
MoTeC's current #18069 product listing gives pin 24 as video input. Older C127 documentation differs; the manufacturer page and manual also differ in the label for pin 32. Verify the exact revision and intended function before connecting video or LIN.
Pin
Name
Function
1
E-TX–
Ethernet Transmit –
2
E-TX+
Ethernet Transmit +
3
AV1
Analogue Voltage Input 1 (with I/O upgrade)
4
AV2
Analogue Voltage Input 2 (with I/O upgrade)
5
AV3
Analogue Voltage Input 3 (with I/O upgrade)
6
AV4
Analogue Voltage Input 4 (with I/O upgrade)
7
8V
Sensor 8 V
8
5V
Sensor 5 V
9
0V
Sensor 0 V
10
E-RX–
Ethernet Receive –
11
E-RX+
Ethernet Receive +
12
AV5
Analogue Voltage Input 5 (with I/O upgrade)
13
AV6
Analogue Voltage Input 6 (with I/O upgrade)
14
DIG1
Digital Input 1
15
DIG2
Digital Input 2
16
AT1
Analogue Temp Input 1 (with I/O upgrade)
17
AT2
Analogue Temp Input 2 (with I/O upgrade)
18
CAN1L
CAN1 Lo
19
CAN1H
CAN1 Hi
20
RS232-1 TX
RS232-1 Transmit
21
SPD1
Speed Input 1
22
SPD2
Speed Input 2
23
SPD3
Speed Input 3
24
VID1
Video Input 1 *
25
RS232-2 RX
RS232-2 Receive
26
CAN2L
CAN2 Lo/RS232 Ground Input
27
CAN2H
CAN2 Hi/RS232 Receive
28
RS232-1 RX
RS232-1 Receive Input
29
AUX1
Auxiliary Output 1 (with I/O upgrade)
30
AUX2
Auxiliary Output 2 (with I/O upgrade)
31
AUX3
Auxiliary Output 3 (with I/O upgrade)
32
AUX4
Auxiliary Output 4 (with I/O upgrade)
33
BAT+
Battery Positive
34
BAT–
Battery Negative
* MoTeC lists live display of the composite video input as requiring the Display Creator upgrade on this C127. Confirm the exact part and revision. MoTeC product specification.
Wiring and configuration
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.
Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.
MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.
Data analysis software
MoTeC i2 data analysis showing channel traces and gauges. Image: MoTeC, reproduced with permission; manufacturer image.
The C127 needs its applicable data-logging upgrade or a logging-equipped kit before it can produce recordings for analysis. MoTeC i2 reviews recorded channels in graphs and reports; i2 Pro features depend on the device upgrade or applicable software licence. See the manufacturer model and analysis comparison and i2 software and licence information.