Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Datalogging and telematics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
MoTeC

MoTeC C125 (MoTeC part #18065) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

MoTeC C125 product photograph
MoTeC C125. Image: MoTeC, reproduced with permission. Manufacturer product page and specifications.

Specifications and options

  • 5-inch colour TFT display, 800 × 480 pixels; configurable channels, alarms and display layouts.
  • Internal logging is an upgrade: 120 MB and rates up to 500 samples per second; USB logging is a further option. Confirm logging is enabled on the unit or included in the purchased kit.
  • Two configurable CAN buses; two RS232 ports. Two digital and three speed inputs are listed. Six analogue voltage inputs, two temperature inputs and four low-side outputs require the I/O upgrade.
  • Manufacturer lists 6–32 V DC operation, three-axis accelerometer and optional T2 telemetry; i2 analysis, GPS timing and connected sensors depend on the installation and options.

MoTeC identifies a previous part #18060; dimensions or construction may differ. Use the document for the unit in hand.

Connector and pinout

34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18065. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.

PinNameFunction
1E-TX–Ethernet Transmit –
2E-TX+Ethernet Transmit +
3AV1Analogue Voltage Input 1 (with I/O upgrade)
4AV2Analogue Voltage Input 2 (with I/O upgrade)
5AV3Analogue Voltage Input 3 (with I/O upgrade)
6AV4Analogue Voltage Input 4 (with I/O upgrade)
78VSensor 8 V
85VSensor 5 V
90VSensor 0 V
10E-RX–Ethernet Receive –
11E-RX+Ethernet Receive +
12AV5Analogue Voltage Input 5 (with I/O upgrade)
13AV6Analogue Voltage Input 6 (with I/O upgrade)
14DIG1Digital Input 1
15DIG2Digital Input 2
16AT1Analogue Temp Input 1 (with I/O upgrade)
17AT2Analogue Temp Input 2 (with I/O upgrade)
18CAN1LCAN1 Lo
19CAN1HCAN1 Hi
20RS232-1 TXRS232-1 Transmit
21SPD1Speed Input 1
22SPD2Speed Input 2
23SPD3Speed Input 3
24VID1Video Input 1 *
25RS232-2 RXRS232-2 Receive
26CAN2LCAN2 Lo/RS232 Ground Input
27CAN2HCAN2 Hi/RS232 Receive
28RS232-1 RXRS232-1 Receive Input
29AUX1Auxiliary Output 1 (with I/O upgrade)
30AUX2Auxiliary Output 2 (with I/O upgrade)
31AUX3Auxiliary Output 3 (with I/O upgrade)
32AUX4Auxiliary Output 4 (with I/O upgrade)
33BAT+Battery Positive
34BAT–Battery Negative

Wiring and configuration

MoTeC C125 simplified power and CAN wiring
Power and CAN example, functional schematic rather than connector geometry. Original Tuning Wiki illustration based on the MoTeC product pinout; verify the actual harness and matching ECU.

Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.

MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.