
Application and identification
The AEM 10-6600 manual lists Nissan 240SX KA24DE, Sentra B13 GA16DE, Pulsar GTi-R N14 SR20DET, NX B13 GA16DE, Altima U13 KA24DE, Bluebird U13 SR20DET and Infiniti G20 P10. Verify the actual engine and harness with AEM: the document conflicts on several applications. Its cover says 1989–94 240X S13, 1991–94 Altima and G20 SR20DET, whereas the connection-table heading says 1989–94 240SX S14, 1993–94 Altima and G20 SR20DE. These source differences are not resolved here.
This Series 2 plug-in standalone ECU replaces the OEM ECU for its specified harness. AEM provides AEMTuner startup calibrations and states that Series 2 is not supported by older AEMPro software. The startup calibration must be tuned for the actual engine. The manual requires the supplied AEM replacement cam/crank trigger disc before starting: its Nissan Series 2 ECU does not support the original Nissan trigger pattern. Consult the AEM 30-6600 installation manual and trigger-disc supplement.
Connector schedule
All 64 numbered positions listed in the AEM 10-6600 connection chart, pages 8–10, are reproduced below. These are wire-view pin numbers, not sequential cavity counts: the chart lists 1–48 and 101–116, and does not assign other numbers. “PnP” means configured in the supplied calibration; “Available” means unused by that calibration or available for reassignment and may require wiring changes; “Dedicated” means fixed. Observe output limits, jumpers and sensor wiring notes in the source. Actual harness wiring varies by model year and trim; check each vehicle connection before installation.
The manual's pin 106 notes say “PnP for Fuel Pump”, although its vehicle destination is a pressure regulator solenoid and pin 104 is the fuel pump relay. The table reproduces the published descriptions; verify the intended wiring with AEM.
| Pin | Vehicle harness destination | AEM EMS function | I/O | Manufacturer notes |
|---|---|---|---|---|
| 1 | Ignition Signal | Coil 1 | Output | PnP for Coil 1, 0-5V falling edge trigger |
| 2 | Tachometer Signal | Low Side 7 | Output | PnP for Tachometer |
| 3 | Ignition Check | --- | --- | Not Used |
| 4 | ECCS Relay control, Ignition Relay control | Main Relay (control) | Output | Dedicated, EMS activates relay with switched GND |
| 5 | --- | Coil 3 | Output | Available Coil 3, 0-5V falling edge trigger |
| 6 | ECCS Ground | Power Ground | Input | Dedicated |
| 7 | Data Link Connector | Coil 2 | Output | Available Coil 2, 0-5V falling edge trigger |
| 8 | EGR Sensor (Except 89-90 Non CA 240SX and SR20DET) | EGT 1 | Input | Available, jumper set for 0-5V Input |
| 9 | Cooling Fan Relay | Low Side 3 + Low Side 12 | Output | PnP for Cooling Fan, can be activated by LS3 or LS12 output |
| 10 | Cooling Fan High Speed (A/T 2.0L only) | Low Side 5 | Output | Available, Switched Ground, 1.5A max |
| 11 | Air Conditioner Relay | Low Side 6 | Output | Available, Switched Ground, 1.5A max |
| 12 | Swirl Control Valve (89-90 240SX Only)/VTC Solenoid (1.6L only) | CAN1H | Input | Dedicated. CAN high side |
| 13 | ECCS Ground | Power Ground | Input | Dedicated |
| 14 | Diagnostics Clock | Injector 7 | Output | Available, Switched Ground, 1.5A Max |
| 15 | Data Link Connector | EGT 2 | Input | Available, jumper set for 0-5V input |
| 16 | Mass Air Flow Sensor | MAF | Input | PnP for MAF Sensor |
| 17 | Mass Air Flow Ground | Power Ground | Input | Dedicated |
| 18 | Engine Coolant Temperature Sensor | Coolant | Input | PnP for Coolant Temp Sensor |
| 19 | Oxygen Sensor | O2 #1 | Input | Dedicated, 0-5V input signal |
| 20 | Throttle Position Sensor | TPS | Input | PnP for Throttle Position Sensor |
| 21 | Sensor Ground | Sensor Ground | Output | Dedicated |
| 22 | Crankshaft Reference Signal | Cam (T2) | Input | Dedicated, must use AEM replacement trigger disc. Connects to pin 30 |
| 23 | Diagnostics check (SR20 only) | Injector 5 | Output | Available, Switched Ground, 1.5A Max |
| 24 | Malfunction Indicator Light | Low Side 10 | Output | Available, Switched Ground, 1.5A Max |
| 25 | Swirl Control Valve (91-94 240SX only) | Coil 4 | Output | Available Coil 4, 0-5V falling edge trigger |
| 26 | Air Temp Sensor (Late 89 and all 90 240SX) | AIT | Input | Available, AIT Sensor Input |
| 27 | Knock Sensor (Except 89-90 240SX & 1.6L) | Knock 1 | Input | PnP for Knock Sensor |
| 28 | Throttle Signal Output (A/T only) | High Side 1 | Output | Available, Switched +12V, 1.5A Max |
| 29 | Sensor Ground | Sensor Ground | Output | Dedicated |
| 30 | Crankshaft Reference Signal | Cam (T2) | Input | Dedicated, must use AEM replacement trigger disc. Connects to pin 22 |
| 31 | Crankshaft Position Sensor Signal | Crank Signal | Input | Dedicated, must use AEM replacement trigger disc. Connects to pin 40 |
| 32 | Vehicle Speed | Vehicle Speed | Input | PnP for Vehicle Speed Sensor |
| 33 | Idle Sw (89-90 240SX)/5th Pos Sw (91-94 240SX) | ADCR11 | Input | Available, 0-5 Volt Input |
| 34 | Start Signal | +12V Switched | Input | Dedicated |
| 35 | Neutral Position Switch | MAP | Input | Available, Manifold Pressure |
| 36 | Ignition Switch | Main Relay (input) | Input | Dedicated, +12V activates Main Relay circuit |
| 37 | Throttle Position Sensor Power | +5V Sensor | Output | Dedicated |
| 38 | Power Supply for ECM | +12V Switched | Input | Dedicated, +12V power when ECCS Relay is on |
| 39 | ECCS Ground | Power Ground | Input | Dedicated |
| 40 | Crankshaft Position Signal | Crank Signal | Input | Dedicated, must use AEM replacement trigger disc. Connects to pin 31 |
| 41 | Air Conditioner Switch | Switch 6 | Input | PnP for A/C Switch |
| 42 | 4th Position Switch (91-94 240SX only) | CAN1L | Input | Dedicated, CAN low side |
| 43 | Power Steering Oil Pressure Switch | Switch 2 | Input | Available, Switched Input |
| 44 | Idle Switch Positive Side (89-90 240SX); Rear window defogger (91-94 240SX) | EGT 3 | Input | Available, jumper set for 0-5V Input |
| 45 | Air Conditioner FICD (Except 2.0L); Position Sw (89-90 240SX) | Low Side 2 | Output | Available, Switched Ground, 1.5A Max |
| 46 | Back-up Power Supply | Permanent +12V | Input | Dedicated, used to store internal log |
| 47 | Power Supply for ECM | +12V Switched | Input | Dedicated, +12V power when ECCS Relay is on |
| 48 | ECCS Ground | Power Ground | Input | Dedicated |
| 101 | Injector 1 | Injector 1 | Output | PnP for Injector 1 (Peak & Hold 4A/1A driver) |
| 102 | Pulse Secondary Air Inj (240SX & 91-93 2.0L only) | Low Side 4 | Output | Available, Switched Ground, 1.5A max |
| 103 | Injector 3 | Injector 3 | Output | PnP for Injector 3 (Peak & Hold 4A/1A driver) |
| 104 | Fuel Pump Relay control | Low Side 11 | Output | PnP for Fuel Pump |
| 105 | EGR Control Solenoid Valve | Injector 6 | Output | Available, Switched Ground, 1.5A max |
| 106 | Pressure Regulator Control Sol (89-90 240SX only) | Low Side 9 | Output | PnP for Fuel Pump |
| 107 | ECCS Ground | Power Ground | Input | Dedicated |
| 108 | ECCS Ground | Power Ground | Input | Dedicated |
| 109 | Back-Up Power Supply | Permanent +12V | Input | Dedicated, used to store internal log |
| 110 | Injector 2 | Injector 2 | Output | PnP for Injector 2 (Peak & Hold 4A/1A driver) |
| 111 | O2 Sensor Heater (91-94 2.0L & 94 1.6L only) | PW 2 | Output | Available, Switched Ground, 1.5 max |
| 112 | Injector 4 | Injector 4 | Output | PnP for Injector 4 (Peak & Hold 4A/1A driver) |
| 113 | Idle Auxiliary Air Control Valve | PW 1 | Output | PnP for Idle Air Control |
| 114 | --- | Injector 8 | Output | Available, Switched Ground, 1.5A max |
| 115 | --- | EGT 4 | Input | Available, jumper set for 0-5V Input |
| 116 | ECCS Ground | Power Ground | Input | Dedicated |
Series 1 conversion differences
Compared with the corresponding 30-1600 Series 1 EMS, AEM documents these changes. After converting a V1.19 Series 1 calibration with AEMTuner, check and manually reconfigure affected functions as directed in the manual.
| Pin | Series 1 function | Series 2 function | AEM note |
|---|---|---|---|
| 12 | Low Side 8 | CAN1H | LS8 not available |
| 15 | Injector 8 | EGT 2 | Injector 8 moved to pin 114 |
| 42 | Switch 1 | CAN1L | Switch 1 not available |
| 114 | EGT 2 | Injector 8 | EGT 2 moved to pin 15 |