Removed text is struck through; added text is highlighted.
The AEM EMS Series 2 30-6101 is an application-specific plug-in ECU. The AEM instructions identify the 1993–1998 Toyota Supra non-turbo and 1993–1997 Lexus SC300/GS300; the connector diagram is specifically titled 1993–1997 Supra/Lexus 2JZ-GE. Check the exact engine, year and harness before installation.
AEM 30-6052 shown as a Series 2 family illustration; connectors and applications differ. AEM / Holley product photograph, reproduced with permission.
Connector assignments
Transcribed from the 30-6101 connection diagram, PDF pages 9–11. Follow the connector diagram and orientation in the manual. A dash is the source’s entry and does not by itself establish an unused or safe connection; available channels depend on configuration. At 4A, the source describes the vehicle brake input as 12 V but the EMS note says the switch must connect to ground: resolve the difference with AEM and the actual harness before wiring.
Connector A
PinVehicle functionAEM EMS functionI/OAvailability and notes1AIgnition Switch (+12V when key on)Main Relay circuitInputDedicated, activates Switch 1 input2AVehicle Speed Signal – from Odo/Trip meterT3 (Vehicle Speed)InputPnP for Vehicle Speed signal3AKickdown switchSwitch 3InputAvailable, switch must connect to GND4ABrake switch input (12V)Switch 6InputAvailable, switch must connect to GND5A---------Not Used6AW- Malfunction Indicator LampLS10OutputAvailable, switched GND output (1.5A max)7A---ATPR (GEAR)InputReserved for future use8ASDL to datalink connector (96-97 only)------Not Used9A2nd gear indicator input (A/T only)ATP2 (GEAR)InputReserved for future use10A1st gear indicator input (A/T only)ATP1 (GEAR)InputReserved for future use11A---CAN1LOutputDedicated12AOD1 to cruise control ECU (AT only)CAN1HOutputDedicated13A---Reserved---Reserved for future use14A---Reserved---Reserved for future use15AELS for Idle up Diode------Not Used16ATacho signal (from ignitor)------Not Used17ATT sig to DATALINK connector (A/T only)Injector 12OutputAvailable, P&H Injector driver 4A/1A18AA/T pattern select sw (A/T only)Switch 5InputAvailable, switch must connect to GND19ATE2 sig to DATALINK connectorInjector 11OutputAvailable, P&H Injector driver 4A/1A20ATE1 sig to DATALINK connector------Not Used21ADI from Fuel Pump ECU------Not Used22AFuel pump control (FPC) signalCoil 8 / LS8OutputPnP 0- 5V FPC signal, not for use with relays23AACMG to A/C Magnetic clutchLS6OutputPNP for A/C compressor relay24AMain Relay ControlMain Relay (HS2)OutputDedicated, activates Main Relay with 12V25AManual indicator light (A/T only)ATIND (Coil7)OutputPNP manual mode indicator (auto only)26A---EFI-TRCInputDedicated27A---EFI+TRCInputDedicated28AOver Drive Switch input (A/T only)Switch 4InputPNP for Overdrive input (auto only)29A---Baro (ADCR12)InputAvailable, Spare 0-5V Sensor Input30ASub O2 signal (CA only)------Not Used31A+12V Power from main relay+12V SwitchedBothDedicated32A+12V Power from main relay------Not Used33A+12V permanent battery backup powerPermanent +12VInputDedicated, used to store internal datalog34AA/C signal from A/C amplifierADCR11 (Switch 7)InputPNP for Air Conditioning request switch35A---HALLPWROutput+12V Output36ASub O2 sensor heater control (CA only)Injector 8OutputSpare P&H Injector 4A/1A37A---------Not Used38A---LS7---Available, switched GND output (1.5A max)39A---------Not Used40A---------Not Used
Connector B
PinVehicle functionAEM EMS functionI/OAvailability and notes1B---Timing GroundOutputDedicated2B---EGT 1InputJumper set for 0-5V input (100kΩ pull-up)3BVSS GroundTiming GroundOutputDedicated4BE11EGT 2InputJumper set for 0-5V input (100kΩ pull-up)5BCam Sensor 2 (NE2) Ground------Not Used6B---Timing GroundOutputDedicated7BDistributor GroundTiming GroundOutputDedicated8BAuto Trans Sol No3 S3 (Auto Trans only)EGT 3InputJumper set for 0-5V input (100kΩ pull-up)9BAuto Trans Sol No2 S2 (Auto Trans only)HS3OutputAvailable, switched +12V output (1.5A max)10BAuto Trans Sol No1 S1 (Auto Trans only)HS4OutputAvailable, switched +12V output (1.5A max)11B---+5V Sensor powerOutputDedicated, sensor only12B---Reserved---Reserved for future use13B---Reserved---Reserved for future use14B---Reserved---Reserved for future use15BInjector 6Injector 6OutputPnP Injector 6 (P&H 4A/1A driver)16BInjector 5Injector 5OutputPnP Injector 5 (P&H 4A/1A driver)17BInjector 4Injector 4OutputPnP Injector 4 (P&H 4A/1A driver)18BInjector 3Injector 3OutputPnP Injector 3 (P&H 4A/1A driver)19BInjector 2Injector 2OutputPnP Injector 2 (P&H 4A/1A driver)20BInjector 1Injector 1OutputPnP Injector 1 (P&H 4A/1A driver)21B---Switch 2InputAvailable Switch input22B---------Not Used23BNo.2 Speed sensor (Auto Trans only)T4 (Spare Speed)InputAvailable magnetic speed sensor input24BAuto Trans Fluid Temp (Auto Trans only)ADCR14InputAvailable 0-5V input, 2.2kΩ pull up to 5V25BDistributor Cam signal 2 (G2) input------Not Used26BDistributor Cam signal 1 (G1) inputCam (T2) signal +InputDedicated27BDistributor - Crank signal (NE) inputCrank signal +InputDedicated28BVF2 sig – to Datalink connector 1 – pin14Sensor GroundOutputDedicated, Sensors only29BVF1 sig – to DATALINK connectorIDLE7OutputAvailable, switched Ground / +12V, 1.5A max30B---IDLE8OutputAvailable, switched +12V/Ground, 1.5A max31B---+12V SwitchedOutputDedicated32BISC4 (pin 3 on ISC harness)IDLE4OutputPNP Idle control motor,33BISC3 (pin 6 on ISC harness)IDLE1OutputPNP Idle control motor34BISC2 (pin 1 on ISC harness)IDLE3OutputPNP Idle control motor35BISC1 (pin 4 on ISC harness)IDLE2OutputPNP Idle control motor36BFuel Pressure Up solenoid valve (93-96)IDLE5OutputAvailable, switched Ground / +12V, 1.5A max37B---IDLE6OutputAvailable, switched +12V/Ground, 1.5A max38B---LS4OutputAvailable, switched GND output (1.5A max)39BACIS solenoid – (intake runner length valve)LS5OutputPNP for ACIS valve40B---LS3OutputAvailable, switched GND output (1.5A max)41B5V Reference+5V SensorOutputDedicated42B---------Not Used43BTPS signal input (VTA1)TPSInputDedicated, 2.2kΩ pull-up resistor to 5V44BCoolant Sensor InputCoolantInputDedicated, 2.2kΩ pull-up resistor to 5V45BAir Temp SensorAir TempInputDedicated46BEGR gas Temp Sensor------Not Used47BOX2 (rear O2 sensor)O2 #1InputDedicated, 0-5V signal48BOX1 (front O2 sensor)O2 #2InputDedicated, 0-5V signal49BRear Knock SensorKnock 2InputDedicated, software knock filter50BFront Knock SensorKnock 1InputDedicated, software knock filter51B---------Not Used52B---Coil 6OutputAvail. Coil6 output, 0-5V falling edge trigger53B---Coil 5OutputAvail. Coil5 output, 0-5V falling edge trigger54B---Coil 4OutputAvail. Coil4 output, 0-5V falling edge trigger55B---Coil 3OutputAvail. Coil3 output, 0-5V falling edge trigger56B---Coil 2OutputAvail. Coil2 output, 0-5V falling edge trigger57BIgniter Control (IGT)Coil 1OutputPnP Coil1 output, 0-5V falling edge trigger58BIgniter return (IGF) to ECU------Not Used59B---LS11OutputAvailable Switched Ground 1.5amp max60B---PW2OutputAvailable boost control solenoid output61B---------Not Used62B---MAPInputDedicated63B---------Not Used64BIdle1 Sw from TPS------Not Used65BSensor GroundSensor GroundOutputDedicated, Sensors only66BVG signal for Airflow meterMAFInputAvailable 0 to 5v input, 100k pull-up to 5V67B---EGT 4InputJumper: 0-5V, thermistor or EGT pull up68B---LS9OutputAvailable Switched Ground 1.5amp max69BE1- GroundPower GroundBothDedicated70B---Injector 7OutputAvailable P&H Injector driver 4A/1A71BOx 1 Heater Ground (96-97)LS12OutputAvailable Switched Ground 1.5amp max72BHT2 – rear O2 heater control (CA only)LS2OutputAvailable Switched Ground 1.5amp max73BHT1 – front O2 heater control (CA only) / Fuel Pressure up solenoid (1997)LS1OutputAvailable Switched Ground 1.5amp max74BEVAP SolenoidInjector 9OutputAvailable P&H Injector driver 4A/1A75BEGR SolenoidInjector 10OutputAvailable P&H Injector driver 4A/1A76BPark / Neutral position switch (AT only)ATPNP (Gear)InputReserved for future use77BCranking signal input (12V)------Not Used78BChassis Ground - EO3 (96-97)Power GroundBothDedicated79BChassis Ground – EO2Power GroundBothDedicated80BChassis Ground – EO1Power GroundBothDedicated
Documentation
AEM 30-6101 installation instructions and connection diagram. The manual’s separate Series 1 versus Series 2 comparison identifies changed assignments; do not substitute the 30-1101 pinout.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: AEM EMS Series 2 30-6101
The AEM EMS Series 2 30-6101 is an application-specific plug-in ECU. The AEM instructions identify the 1993–1998 Toyota Supra non-turbo and 1993–1997 Lexus SC300/GS300; the connector diagram is specifically titled 1993–1997 Supra/Lexus 2JZ-GE. Check the exact engine, year and harness before installation.
AEM 30-6052 shown as a Series 2 family illustration; connectors and applications differ. AEM / Holley product photograph, reproduced with permission.
Connector assignments
Transcribed from the 30-6101 connection diagram, PDF pages 9–11. Follow the connector diagram and orientation in the manual. A dash is the source’s entry and does not by itself establish an unused or safe connection; available channels depend on configuration. At 4A, the source describes the vehicle brake input as 12 V but the EMS note says the switch must connect to ground: resolve the difference with AEM and the actual harness before wiring.
Connector A
Pin
Vehicle function
AEM EMS function
I/O
Availability and notes
1A
Ignition Switch (+12V when key on)
Main Relay circuit
Input
Dedicated, activates Switch 1 input
2A
Vehicle Speed Signal – from Odo/Trip meter
T3 (Vehicle Speed)
Input
PnP for Vehicle Speed signal
3A
Kickdown switch
Switch 3
Input
Available, switch must connect to GND
4A
Brake switch input (12V)
Switch 6
Input
Available, switch must connect to GND
5A
---
---
---
Not Used
6A
W- Malfunction Indicator Lamp
LS10
Output
Available, switched GND output (1.5A max)
7A
---
ATPR (GEAR)
Input
Reserved for future use
8A
SDL to datalink connector (96-97 only)
---
---
Not Used
9A
2nd gear indicator input (A/T only)
ATP2 (GEAR)
Input
Reserved for future use
10A
1st gear indicator input (A/T only)
ATP1 (GEAR)
Input
Reserved for future use
11A
---
CAN1L
Output
Dedicated
12A
OD1 to cruise control ECU (AT only)
CAN1H
Output
Dedicated
13A
---
Reserved
---
Reserved for future use
14A
---
Reserved
---
Reserved for future use
15A
ELS for Idle up Diode
---
---
Not Used
16A
Tacho signal (from ignitor)
---
---
Not Used
17A
TT sig to DATALINK connector (A/T only)
Injector 12
Output
Available, P&H Injector driver 4A/1A
18A
A/T pattern select sw (A/T only)
Switch 5
Input
Available, switch must connect to GND
19A
TE2 sig to DATALINK connector
Injector 11
Output
Available, P&H Injector driver 4A/1A
20A
TE1 sig to DATALINK connector
---
---
Not Used
21A
DI from Fuel Pump ECU
---
---
Not Used
22A
Fuel pump control (FPC) signal
Coil 8 / LS8
Output
PnP 0- 5V FPC signal, not for use with relays
23A
ACMG to A/C Magnetic clutch
LS6
Output
PNP for A/C compressor relay
24A
Main Relay Control
Main Relay (HS2)
Output
Dedicated, activates Main Relay with 12V
25A
Manual indicator light (A/T only)
ATIND (Coil7)
Output
PNP manual mode indicator (auto only)
26A
---
EFI-TRC
Input
Dedicated
27A
---
EFI+TRC
Input
Dedicated
28A
Over Drive Switch input (A/T only)
Switch 4
Input
PNP for Overdrive input (auto only)
29A
---
Baro (ADCR12)
Input
Available, Spare 0-5V Sensor Input
30A
Sub O2 signal (CA only)
---
---
Not Used
31A
+12V Power from main relay
+12V Switched
Both
Dedicated
32A
+12V Power from main relay
---
---
Not Used
33A
+12V permanent battery backup power
Permanent +12V
Input
Dedicated, used to store internal datalog
34A
A/C signal from A/C amplifier
ADCR11 (Switch 7)
Input
PNP for Air Conditioning request switch
35A
---
HALLPWR
Output
+12V Output
36A
Sub O2 sensor heater control (CA only)
Injector 8
Output
Spare P&H Injector 4A/1A
37A
---
---
---
Not Used
38A
---
LS7
---
Available, switched GND output (1.5A max)
39A
---
---
---
Not Used
40A
---
---
---
Not Used
Connector B
Pin
Vehicle function
AEM EMS function
I/O
Availability and notes
1B
---
Timing Ground
Output
Dedicated
2B
---
EGT 1
Input
Jumper set for 0-5V input (100kΩ pull-up)
3B
VSS Ground
Timing Ground
Output
Dedicated
4B
E11
EGT 2
Input
Jumper set for 0-5V input (100kΩ pull-up)
5B
Cam Sensor 2 (NE2) Ground
---
---
Not Used
6B
---
Timing Ground
Output
Dedicated
7B
Distributor Ground
Timing Ground
Output
Dedicated
8B
Auto Trans Sol No3 S3 (Auto Trans only)
EGT 3
Input
Jumper set for 0-5V input (100kΩ pull-up)
9B
Auto Trans Sol No2 S2 (Auto Trans only)
HS3
Output
Available, switched +12V output (1.5A max)
10B
Auto Trans Sol No1 S1 (Auto Trans only)
HS4
Output
Available, switched +12V output (1.5A max)
11B
---
+5V Sensor power
Output
Dedicated, sensor only
12B
---
Reserved
---
Reserved for future use
13B
---
Reserved
---
Reserved for future use
14B
---
Reserved
---
Reserved for future use
15B
Injector 6
Injector 6
Output
PnP Injector 6 (P&H 4A/1A driver)
16B
Injector 5
Injector 5
Output
PnP Injector 5 (P&H 4A/1A driver)
17B
Injector 4
Injector 4
Output
PnP Injector 4 (P&H 4A/1A driver)
18B
Injector 3
Injector 3
Output
PnP Injector 3 (P&H 4A/1A driver)
19B
Injector 2
Injector 2
Output
PnP Injector 2 (P&H 4A/1A driver)
20B
Injector 1
Injector 1
Output
PnP Injector 1 (P&H 4A/1A driver)
21B
---
Switch 2
Input
Available Switch input
22B
---
---
---
Not Used
23B
No.2 Speed sensor (Auto Trans only)
T4 (Spare Speed)
Input
Available magnetic speed sensor input
24B
Auto Trans Fluid Temp (Auto Trans only)
ADCR14
Input
Available 0-5V input, 2.2kΩ pull up to 5V
25B
Distributor Cam signal 2 (G2) input
---
---
Not Used
26B
Distributor Cam signal 1 (G1) input
Cam (T2) signal +
Input
Dedicated
27B
Distributor - Crank signal (NE) input
Crank signal +
Input
Dedicated
28B
VF2 sig – to Datalink connector 1 – pin14
Sensor Ground
Output
Dedicated, Sensors only
29B
VF1 sig – to DATALINK connector
IDLE7
Output
Available, switched Ground / +12V, 1.5A max
30B
---
IDLE8
Output
Available, switched +12V/Ground, 1.5A max
31B
---
+12V Switched
Output
Dedicated
32B
ISC4 (pin 3 on ISC harness)
IDLE4
Output
PNP Idle control motor,
33B
ISC3 (pin 6 on ISC harness)
IDLE1
Output
PNP Idle control motor
34B
ISC2 (pin 1 on ISC harness)
IDLE3
Output
PNP Idle control motor
35B
ISC1 (pin 4 on ISC harness)
IDLE2
Output
PNP Idle control motor
36B
Fuel Pressure Up solenoid valve (93-96)
IDLE5
Output
Available, switched Ground / +12V, 1.5A max
37B
---
IDLE6
Output
Available, switched +12V/Ground, 1.5A max
38B
---
LS4
Output
Available, switched GND output (1.5A max)
39B
ACIS solenoid – (intake runner length valve)
LS5
Output
PNP for ACIS valve
40B
---
LS3
Output
Available, switched GND output (1.5A max)
41B
5V Reference
+5V Sensor
Output
Dedicated
42B
---
---
---
Not Used
43B
TPS signal input (VTA1)
TPS
Input
Dedicated, 2.2kΩ pull-up resistor to 5V
44B
Coolant Sensor Input
Coolant
Input
Dedicated, 2.2kΩ pull-up resistor to 5V
45B
Air Temp Sensor
Air Temp
Input
Dedicated
46B
EGR gas Temp Sensor
---
---
Not Used
47B
OX2 (rear O2 sensor)
O2 #1
Input
Dedicated, 0-5V signal
48B
OX1 (front O2 sensor)
O2 #2
Input
Dedicated, 0-5V signal
49B
Rear Knock Sensor
Knock 2
Input
Dedicated, software knock filter
50B
Front Knock Sensor
Knock 1
Input
Dedicated, software knock filter
51B
---
---
---
Not Used
52B
---
Coil 6
Output
Avail. Coil6 output, 0-5V falling edge trigger
53B
---
Coil 5
Output
Avail. Coil5 output, 0-5V falling edge trigger
54B
---
Coil 4
Output
Avail. Coil4 output, 0-5V falling edge trigger
55B
---
Coil 3
Output
Avail. Coil3 output, 0-5V falling edge trigger
56B
---
Coil 2
Output
Avail. Coil2 output, 0-5V falling edge trigger
57B
Igniter Control (IGT)
Coil 1
Output
PnP Coil1 output, 0-5V falling edge trigger
58B
Igniter return (IGF) to ECU
---
---
Not Used
59B
---
LS11
Output
Available Switched Ground 1.5amp max
60B
---
PW2
Output
Available boost control solenoid output
61B
---
---
---
Not Used
62B
---
MAP
Input
Dedicated
63B
---
---
---
Not Used
64B
Idle1 Sw from TPS
---
---
Not Used
65B
Sensor Ground
Sensor Ground
Output
Dedicated, Sensors only
66B
VG signal for Airflow meter
MAF
Input
Available 0 to 5v input, 100k pull-up to 5V
67B
---
EGT 4
Input
Jumper: 0-5V, thermistor or EGT pull up
68B
---
LS9
Output
Available Switched Ground 1.5amp max
69B
E1- Ground
Power Ground
Both
Dedicated
70B
---
Injector 7
Output
Available P&H Injector driver 4A/1A
71B
Ox 1 Heater Ground (96-97)
LS12
Output
Available Switched Ground 1.5amp max
72B
HT2 – rear O2 heater control (CA only)
LS2
Output
Available Switched Ground 1.5amp max
73B
HT1 – front O2 heater control (CA only) / Fuel Pressure up solenoid (1997)
The AEM EMS Series 2 30-6101 is an application-specific plug-in ECU. The AEM instructions identify the 1993–1998 Toyota Supra non-turbo and 1993–1997 Lexus SC300/GS300; the connector diagram is specifically titled 1993–1997 Supra/Lexus 2JZ-GE. Check the exact engine, year and harness before installation.
AEM 30-6052 shown as a Series 2 family illustration; connectors and applications differ. AEM / Holley product photograph, reproduced with permission.
Connector assignments
Transcribed from the 30-6101 connection diagram, PDF pages 9–11. Follow the connector diagram and orientation in the manual. A dash is the source’s entry and does not by itself establish an unused or safe connection; available channels depend on configuration. At 4A, the source describes the vehicle brake input as 12 V but the EMS note says the switch must connect to ground: resolve the difference with AEM and the actual harness before wiring.
Connector A
Pin
Vehicle function
AEM EMS function
I/O
Availability and notes
1A
Ignition Switch (+12V when key on)
Main Relay circuit
Input
Dedicated, activates Switch 1 input
2A
Vehicle Speed Signal – from Odo/Trip meter
T3 (Vehicle Speed)
Input
PnP for Vehicle Speed signal
3A
Kickdown switch
Switch 3
Input
Available, switch must connect to GND
4A
Brake switch input (12V)
Switch 6
Input
Available, switch must connect to GND
5A
---
---
---
Not Used
6A
W- Malfunction Indicator Lamp
LS10
Output
Available, switched GND output (1.5A max)
7A
---
ATPR (GEAR)
Input
Reserved for future use
8A
SDL to datalink connector (96-97 only)
---
---
Not Used
9A
2nd gear indicator input (A/T only)
ATP2 (GEAR)
Input
Reserved for future use
10A
1st gear indicator input (A/T only)
ATP1 (GEAR)
Input
Reserved for future use
11A
---
CAN1L
Output
Dedicated
12A
OD1 to cruise control ECU (AT only)
CAN1H
Output
Dedicated
13A
---
Reserved
---
Reserved for future use
14A
---
Reserved
---
Reserved for future use
15A
ELS for Idle up Diode
---
---
Not Used
16A
Tacho signal (from ignitor)
---
---
Not Used
17A
TT sig to DATALINK connector (A/T only)
Injector 12
Output
Available, P&H Injector driver 4A/1A
18A
A/T pattern select sw (A/T only)
Switch 5
Input
Available, switch must connect to GND
19A
TE2 sig to DATALINK connector
Injector 11
Output
Available, P&H Injector driver 4A/1A
20A
TE1 sig to DATALINK connector
---
---
Not Used
21A
DI from Fuel Pump ECU
---
---
Not Used
22A
Fuel pump control (FPC) signal
Coil 8 / LS8
Output
PnP 0- 5V FPC signal, not for use with relays
23A
ACMG to A/C Magnetic clutch
LS6
Output
PNP for A/C compressor relay
24A
Main Relay Control
Main Relay (HS2)
Output
Dedicated, activates Main Relay with 12V
25A
Manual indicator light (A/T only)
ATIND (Coil7)
Output
PNP manual mode indicator (auto only)
26A
---
EFI-TRC
Input
Dedicated
27A
---
EFI+TRC
Input
Dedicated
28A
Over Drive Switch input (A/T only)
Switch 4
Input
PNP for Overdrive input (auto only)
29A
---
Baro (ADCR12)
Input
Available, Spare 0-5V Sensor Input
30A
Sub O2 signal (CA only)
---
---
Not Used
31A
+12V Power from main relay
+12V Switched
Both
Dedicated
32A
+12V Power from main relay
---
---
Not Used
33A
+12V permanent battery backup power
Permanent +12V
Input
Dedicated, used to store internal datalog
34A
A/C signal from A/C amplifier
ADCR11 (Switch 7)
Input
PNP for Air Conditioning request switch
35A
---
HALLPWR
Output
+12V Output
36A
Sub O2 sensor heater control (CA only)
Injector 8
Output
Spare P&H Injector 4A/1A
37A
---
---
---
Not Used
38A
---
LS7
---
Available, switched GND output (1.5A max)
39A
---
---
---
Not Used
40A
---
---
---
Not Used
Connector B
Pin
Vehicle function
AEM EMS function
I/O
Availability and notes
1B
---
Timing Ground
Output
Dedicated
2B
---
EGT 1
Input
Jumper set for 0-5V input (100kΩ pull-up)
3B
VSS Ground
Timing Ground
Output
Dedicated
4B
E11
EGT 2
Input
Jumper set for 0-5V input (100kΩ pull-up)
5B
Cam Sensor 2 (NE2) Ground
---
---
Not Used
6B
---
Timing Ground
Output
Dedicated
7B
Distributor Ground
Timing Ground
Output
Dedicated
8B
Auto Trans Sol No3 S3 (Auto Trans only)
EGT 3
Input
Jumper set for 0-5V input (100kΩ pull-up)
9B
Auto Trans Sol No2 S2 (Auto Trans only)
HS3
Output
Available, switched +12V output (1.5A max)
10B
Auto Trans Sol No1 S1 (Auto Trans only)
HS4
Output
Available, switched +12V output (1.5A max)
11B
---
+5V Sensor power
Output
Dedicated, sensor only
12B
---
Reserved
---
Reserved for future use
13B
---
Reserved
---
Reserved for future use
14B
---
Reserved
---
Reserved for future use
15B
Injector 6
Injector 6
Output
PnP Injector 6 (P&H 4A/1A driver)
16B
Injector 5
Injector 5
Output
PnP Injector 5 (P&H 4A/1A driver)
17B
Injector 4
Injector 4
Output
PnP Injector 4 (P&H 4A/1A driver)
18B
Injector 3
Injector 3
Output
PnP Injector 3 (P&H 4A/1A driver)
19B
Injector 2
Injector 2
Output
PnP Injector 2 (P&H 4A/1A driver)
20B
Injector 1
Injector 1
Output
PnP Injector 1 (P&H 4A/1A driver)
21B
---
Switch 2
Input
Available Switch input
22B
---
---
---
Not Used
23B
No.2 Speed sensor (Auto Trans only)
T4 (Spare Speed)
Input
Available magnetic speed sensor input
24B
Auto Trans Fluid Temp (Auto Trans only)
ADCR14
Input
Available 0-5V input, 2.2kΩ pull up to 5V
25B
Distributor Cam signal 2 (G2) input
---
---
Not Used
26B
Distributor Cam signal 1 (G1) input
Cam (T2) signal +
Input
Dedicated
27B
Distributor - Crank signal (NE) input
Crank signal +
Input
Dedicated
28B
VF2 sig – to Datalink connector 1 – pin14
Sensor Ground
Output
Dedicated, Sensors only
29B
VF1 sig – to DATALINK connector
IDLE7
Output
Available, switched Ground / +12V, 1.5A max
30B
---
IDLE8
Output
Available, switched +12V/Ground, 1.5A max
31B
---
+12V Switched
Output
Dedicated
32B
ISC4 (pin 3 on ISC harness)
IDLE4
Output
PNP Idle control motor,
33B
ISC3 (pin 6 on ISC harness)
IDLE1
Output
PNP Idle control motor
34B
ISC2 (pin 1 on ISC harness)
IDLE3
Output
PNP Idle control motor
35B
ISC1 (pin 4 on ISC harness)
IDLE2
Output
PNP Idle control motor
36B
Fuel Pressure Up solenoid valve (93-96)
IDLE5
Output
Available, switched Ground / +12V, 1.5A max
37B
---
IDLE6
Output
Available, switched +12V/Ground, 1.5A max
38B
---
LS4
Output
Available, switched GND output (1.5A max)
39B
ACIS solenoid – (intake runner length valve)
LS5
Output
PNP for ACIS valve
40B
---
LS3
Output
Available, switched GND output (1.5A max)
41B
5V Reference
+5V Sensor
Output
Dedicated
42B
---
---
---
Not Used
43B
TPS signal input (VTA1)
TPS
Input
Dedicated, 2.2kΩ pull-up resistor to 5V
44B
Coolant Sensor Input
Coolant
Input
Dedicated, 2.2kΩ pull-up resistor to 5V
45B
Air Temp Sensor
Air Temp
Input
Dedicated
46B
EGR gas Temp Sensor
---
---
Not Used
47B
OX2 (rear O2 sensor)
O2 #1
Input
Dedicated, 0-5V signal
48B
OX1 (front O2 sensor)
O2 #2
Input
Dedicated, 0-5V signal
49B
Rear Knock Sensor
Knock 2
Input
Dedicated, software knock filter
50B
Front Knock Sensor
Knock 1
Input
Dedicated, software knock filter
51B
---
---
---
Not Used
52B
---
Coil 6
Output
Avail. Coil6 output, 0-5V falling edge trigger
53B
---
Coil 5
Output
Avail. Coil5 output, 0-5V falling edge trigger
54B
---
Coil 4
Output
Avail. Coil4 output, 0-5V falling edge trigger
55B
---
Coil 3
Output
Avail. Coil3 output, 0-5V falling edge trigger
56B
---
Coil 2
Output
Avail. Coil2 output, 0-5V falling edge trigger
57B
Igniter Control (IGT)
Coil 1
Output
PnP Coil1 output, 0-5V falling edge trigger
58B
Igniter return (IGF) to ECU
---
---
Not Used
59B
---
LS11
Output
Available Switched Ground 1.5amp max
60B
---
PW2
Output
Available boost control solenoid output
61B
---
---
---
Not Used
62B
---
MAP
Input
Dedicated
63B
---
---
---
Not Used
64B
Idle1 Sw from TPS
---
---
Not Used
65B
Sensor Ground
Sensor Ground
Output
Dedicated, Sensors only
66B
VG signal for Airflow meter
MAF
Input
Available 0 to 5v input, 100k pull-up to 5V
67B
---
EGT 4
Input
Jumper: 0-5V, thermistor or EGT pull up
68B
---
LS9
Output
Available Switched Ground 1.5amp max
69B
E1- Ground
Power Ground
Both
Dedicated
70B
---
Injector 7
Output
Available P&H Injector driver 4A/1A
71B
Ox 1 Heater Ground (96-97)
LS12
Output
Available Switched Ground 1.5amp max
72B
HT2 – rear O2 heater control (CA only)
LS2
Output
Available Switched Ground 1.5amp max
73B
HT1 – front O2 heater control (CA only) / Fuel Pressure up solenoid (1997)