The AEM EMS Series 2 30-6101 is an application-specific plug-in ECU. The AEM instructions identify the 1993–1998 Toyota Supra non-turbo and 1993–1997 Lexus SC300/GS300; the connector diagram is specifically titled 1993–1997 Supra/Lexus 2JZ-GE. Check the exact engine, year and harness before installation.

Connector assignments
Transcribed from the 30-6101 connection diagram, PDF pages 9–11. Follow the connector diagram and orientation in the manual. A dash is the source’s entry and does not by itself establish an unused or safe connection; available channels depend on configuration. At 4A, the source describes the vehicle brake input as 12 V but the EMS note says the switch must connect to ground: resolve the difference with AEM and the actual harness before wiring.
Connector A
| Pin | Vehicle function | AEM EMS function | I/O | Availability and notes |
|---|---|---|---|---|
| 1A | Ignition Switch (+12V when key on) | Main Relay circuit | Input | Dedicated, activates Switch 1 input |
| 2A | Vehicle Speed Signal – from Odo/Trip meter | T3 (Vehicle Speed) | Input | PnP for Vehicle Speed signal |
| 3A | Kickdown switch | Switch 3 | Input | Available, switch must connect to GND |
| 4A | Brake switch input (12V) | Switch 6 | Input | Available, switch must connect to GND |
| 5A | --- | --- | --- | Not Used |
| 6A | W- Malfunction Indicator Lamp | LS10 | Output | Available, switched GND output (1.5A max) |
| 7A | --- | ATPR (GEAR) | Input | Reserved for future use |
| 8A | SDL to datalink connector (96-97 only) | --- | --- | Not Used |
| 9A | 2nd gear indicator input (A/T only) | ATP2 (GEAR) | Input | Reserved for future use |
| 10A | 1st gear indicator input (A/T only) | ATP1 (GEAR) | Input | Reserved for future use |
| 11A | --- | CAN1L | Output | Dedicated |
| 12A | OD1 to cruise control ECU (AT only) | CAN1H | Output | Dedicated |
| 13A | --- | Reserved | --- | Reserved for future use |
| 14A | --- | Reserved | --- | Reserved for future use |
| 15A | ELS for Idle up Diode | --- | --- | Not Used |
| 16A | Tacho signal (from ignitor) | --- | --- | Not Used |
| 17A | TT sig to DATALINK connector (A/T only) | Injector 12 | Output | Available, P&H Injector driver 4A/1A |
| 18A | A/T pattern select sw (A/T only) | Switch 5 | Input | Available, switch must connect to GND |
| 19A | TE2 sig to DATALINK connector | Injector 11 | Output | Available, P&H Injector driver 4A/1A |
| 20A | TE1 sig to DATALINK connector | --- | --- | Not Used |
| 21A | DI from Fuel Pump ECU | --- | --- | Not Used |
| 22A | Fuel pump control (FPC) signal | Coil 8 / LS8 | Output | PnP 0- 5V FPC signal, not for use with relays |
| 23A | ACMG to A/C Magnetic clutch | LS6 | Output | PNP for A/C compressor relay |
| 24A | Main Relay Control | Main Relay (HS2) | Output | Dedicated, activates Main Relay with 12V |
| 25A | Manual indicator light (A/T only) | ATIND (Coil7) | Output | PNP manual mode indicator (auto only) |
| 26A | --- | EFI-TRC | Input | Dedicated |
| 27A | --- | EFI+TRC | Input | Dedicated |
| 28A | Over Drive Switch input (A/T only) | Switch 4 | Input | PNP for Overdrive input (auto only) |
| 29A | --- | Baro (ADCR12) | Input | Available, Spare 0-5V Sensor Input |
| 30A | Sub O2 signal (CA only) | --- | --- | Not Used |
| 31A | +12V Power from main relay | +12V Switched | Both | Dedicated |
| 32A | +12V Power from main relay | --- | --- | Not Used |
| 33A | +12V permanent battery backup power | Permanent +12V | Input | Dedicated, used to store internal datalog |
| 34A | A/C signal from A/C amplifier | ADCR11 (Switch 7) | Input | PNP for Air Conditioning request switch |
| 35A | --- | HALLPWR | Output | +12V Output |
| 36A | Sub O2 sensor heater control (CA only) | Injector 8 | Output | Spare P&H Injector 4A/1A |
| 37A | --- | --- | --- | Not Used |
| 38A | --- | LS7 | --- | Available, switched GND output (1.5A max) |
| 39A | --- | --- | --- | Not Used |
| 40A | --- | --- | --- | Not Used |
Connector B
| Pin | Vehicle function | AEM EMS function | I/O | Availability and notes |
|---|---|---|---|---|
| 1B | --- | Timing Ground | Output | Dedicated |
| 2B | --- | EGT 1 | Input | Jumper set for 0-5V input (100kΩ pull-up) |
| 3B | VSS Ground | Timing Ground | Output | Dedicated |
| 4B | E11 | EGT 2 | Input | Jumper set for 0-5V input (100kΩ pull-up) |
| 5B | Cam Sensor 2 (NE2) Ground | --- | --- | Not Used |
| 6B | --- | Timing Ground | Output | Dedicated |
| 7B | Distributor Ground | Timing Ground | Output | Dedicated |
| 8B | Auto Trans Sol No3 S3 (Auto Trans only) | EGT 3 | Input | Jumper set for 0-5V input (100kΩ pull-up) |
| 9B | Auto Trans Sol No2 S2 (Auto Trans only) | HS3 | Output | Available, switched +12V output (1.5A max) |
| 10B | Auto Trans Sol No1 S1 (Auto Trans only) | HS4 | Output | Available, switched +12V output (1.5A max) |
| 11B | --- | +5V Sensor power | Output | Dedicated, sensor only |
| 12B | --- | Reserved | --- | Reserved for future use |
| 13B | --- | Reserved | --- | Reserved for future use |
| 14B | --- | Reserved | --- | Reserved for future use |
| 15B | Injector 6 | Injector 6 | Output | PnP Injector 6 (P&H 4A/1A driver) |
| 16B | Injector 5 | Injector 5 | Output | PnP Injector 5 (P&H 4A/1A driver) |
| 17B | Injector 4 | Injector 4 | Output | PnP Injector 4 (P&H 4A/1A driver) |
| 18B | Injector 3 | Injector 3 | Output | PnP Injector 3 (P&H 4A/1A driver) |
| 19B | Injector 2 | Injector 2 | Output | PnP Injector 2 (P&H 4A/1A driver) |
| 20B | Injector 1 | Injector 1 | Output | PnP Injector 1 (P&H 4A/1A driver) |
| 21B | --- | Switch 2 | Input | Available Switch input |
| 22B | --- | --- | --- | Not Used |
| 23B | No.2 Speed sensor (Auto Trans only) | T4 (Spare Speed) | Input | Available magnetic speed sensor input |
| 24B | Auto Trans Fluid Temp (Auto Trans only) | ADCR14 | Input | Available 0-5V input, 2.2kΩ pull up to 5V |
| 25B | Distributor Cam signal 2 (G2) input | --- | --- | Not Used |
| 26B | Distributor Cam signal 1 (G1) input | Cam (T2) signal + | Input | Dedicated |
| 27B | Distributor - Crank signal (NE) input | Crank signal + | Input | Dedicated |
| 28B | VF2 sig – to Datalink connector 1 – pin14 | Sensor Ground | Output | Dedicated, Sensors only |
| 29B | VF1 sig – to DATALINK connector | IDLE7 | Output | Available, switched Ground / +12V, 1.5A max |
| 30B | --- | IDLE8 | Output | Available, switched +12V/Ground, 1.5A max |
| 31B | --- | +12V Switched | Output | Dedicated |
| 32B | ISC4 (pin 3 on ISC harness) | IDLE4 | Output | PNP Idle control motor, |
| 33B | ISC3 (pin 6 on ISC harness) | IDLE1 | Output | PNP Idle control motor |
| 34B | ISC2 (pin 1 on ISC harness) | IDLE3 | Output | PNP Idle control motor |
| 35B | ISC1 (pin 4 on ISC harness) | IDLE2 | Output | PNP Idle control motor |
| 36B | Fuel Pressure Up solenoid valve (93-96) | IDLE5 | Output | Available, switched Ground / +12V, 1.5A max |
| 37B | --- | IDLE6 | Output | Available, switched +12V/Ground, 1.5A max |
| 38B | --- | LS4 | Output | Available, switched GND output (1.5A max) |
| 39B | ACIS solenoid – (intake runner length valve) | LS5 | Output | PNP for ACIS valve |
| 40B | --- | LS3 | Output | Available, switched GND output (1.5A max) |
| 41B | 5V Reference | +5V Sensor | Output | Dedicated |
| 42B | --- | --- | --- | Not Used |
| 43B | TPS signal input (VTA1) | TPS | Input | Dedicated, 2.2kΩ pull-up resistor to 5V |
| 44B | Coolant Sensor Input | Coolant | Input | Dedicated, 2.2kΩ pull-up resistor to 5V |
| 45B | Air Temp Sensor | Air Temp | Input | Dedicated |
| 46B | EGR gas Temp Sensor | --- | --- | Not Used |
| 47B | OX2 (rear O2 sensor) | O2 #1 | Input | Dedicated, 0-5V signal |
| 48B | OX1 (front O2 sensor) | O2 #2 | Input | Dedicated, 0-5V signal |
| 49B | Rear Knock Sensor | Knock 2 | Input | Dedicated, software knock filter |
| 50B | Front Knock Sensor | Knock 1 | Input | Dedicated, software knock filter |
| 51B | --- | --- | --- | Not Used |
| 52B | --- | Coil 6 | Output | Avail. Coil6 output, 0-5V falling edge trigger |
| 53B | --- | Coil 5 | Output | Avail. Coil5 output, 0-5V falling edge trigger |
| 54B | --- | Coil 4 | Output | Avail. Coil4 output, 0-5V falling edge trigger |
| 55B | --- | Coil 3 | Output | Avail. Coil3 output, 0-5V falling edge trigger |
| 56B | --- | Coil 2 | Output | Avail. Coil2 output, 0-5V falling edge trigger |
| 57B | Igniter Control (IGT) | Coil 1 | Output | PnP Coil1 output, 0-5V falling edge trigger |
| 58B | Igniter return (IGF) to ECU | --- | --- | Not Used |
| 59B | --- | LS11 | Output | Available Switched Ground 1.5amp max |
| 60B | --- | PW2 | Output | Available boost control solenoid output |
| 61B | --- | --- | --- | Not Used |
| 62B | --- | MAP | Input | Dedicated |
| 63B | --- | --- | --- | Not Used |
| 64B | Idle1 Sw from TPS | --- | --- | Not Used |
| 65B | Sensor Ground | Sensor Ground | Output | Dedicated, Sensors only |
| 66B | VG signal for Airflow meter | MAF | Input | Available 0 to 5v input, 100k pull-up to 5V |
| 67B | --- | EGT 4 | Input | Jumper: 0-5V, thermistor or EGT pull up |
| 68B | --- | LS9 | Output | Available Switched Ground 1.5amp max |
| 69B | E1- Ground | Power Ground | Both | Dedicated |
| 70B | --- | Injector 7 | Output | Available P&H Injector driver 4A/1A |
| 71B | Ox 1 Heater Ground (96-97) | LS12 | Output | Available Switched Ground 1.5amp max |
| 72B | HT2 – rear O2 heater control (CA only) | LS2 | Output | Available Switched Ground 1.5amp max |
| 73B | HT1 – front O2 heater control (CA only) / Fuel Pressure up solenoid (1997) | LS1 | Output | Available Switched Ground 1.5amp max |
| 74B | EVAP Solenoid | Injector 9 | Output | Available P&H Injector driver 4A/1A |
| 75B | EGR Solenoid | Injector 10 | Output | Available P&H Injector driver 4A/1A |
| 76B | Park / Neutral position switch (AT only) | ATPNP (Gear) | Input | Reserved for future use |
| 77B | Cranking signal input (12V) | --- | --- | Not Used |
| 78B | Chassis Ground - EO3 (96-97) | Power Ground | Both | Dedicated |
| 79B | Chassis Ground – EO2 | Power Ground | Both | Dedicated |
| 80B | Chassis Ground – EO1 | Power Ground | Both | Dedicated |
Documentation
AEM 30-6101 installation instructions and connection diagram. The manual’s separate Series 1 versus Series 2 comparison identifies changed assignments; do not substitute the 30-1101 pinout.