Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

GS19.11 is a control-unit designation used in selected ZF 6HP28 mechatronics. Jaguar shift-by-wire and Land Rover mechanical-shift versions must be identified separately.

A ZF 6HP26 cutaway for family context; it is not a photograph identifying this controller or a Jaguar 6HP28. Ralf Pfeifer, Wikimedia Commons, CC BY-SA 3.0, unmodified.

Illustrative ZF 6HP mechatronic electronic module and connector sleeve, from ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission. This general image does not identify the controller part number or a Jaguar-specific unit.

Identification and examples

Jaguar specialist Old Jaguar lists Bosch 0260550043 / ZF 6058007115 for the GS19.11 E-shift 6HP28 and cites Jaguar X150, X250 and X351 examples. Its mechanical-shift Land Rover example lists different numbers, including Bosch 0260550041. The specialist's listing is not a guarantee of interchange: verify model year, engine, hardware and software ID, selector, VIN and gearbox specification.

A 2010 Jaguar XF 5.0 SC service description identifies a 6HP28 with integrated TCM/mechatronic, rotary selector and electronic park lock. It does not identify a Bosch number, so it is an application example, not proof that every 2010 XF uses 0260550043.

Jaguar 6HP26/28 shift-by-wire connector example

The 16-way gearbox connector assignments below are transcribed from William Henney's 6HP26 training presentation, specifically its “Jaguar 6HP26/28 with shift-by-wire” table. The presentation does not associate the table with a specific Bosch number or VIN and does not clearly state connector-face orientation. It gives a numbered connector photograph: check that and the actual VIN-specific wiring document and moulded cavity numbers before connecting. These are documented assignments for the described example, not independently bench-verified or a guaranteed pinout for this particular controller number. “Not used” applies to the source example only.

CavityFunction in source example1Not used in source example2CAN low3ISO K (example application)4Not used in source example5Not used in source example6CAN high7Not used in source example8LIN selector-position information9Terminal 15 wake-up10Park / no-park signal11Not used in source example12Not used in source example13Terminal 31-1 ground14Terminal 30 permanent positive15Not used in source example16Terminal 31-2 ground

The same presentation's mechanical-selector example has different functions at cavities 1, 4, 5 and 8. Do not transfer these values to mechanical-shift Jaguar, Land Rover, BMW or another car without its own wiring evidence.

Programming and recalibration

PCMflash lists Jaguar/Land Rover 6HP26/28 in module 81's manual, with reading, writing and checksum for specific TCM families. Magicmotorsport FLEX lists selected 6HP bench duplication in its duplicable units list; duplication alone does not prove calibration editing for this exact number. Check the current tool's vehicle, ECU identity, protocol and required licence. A calibration editor or service is separate from the device that reads and writes a file.

Use manufacturer-prescribed service configuration and a recovery plan when replacing the TCM. A compatible blank or used controller may require application-specific software and setup; match the vehicle and preserve its original identification and configuration before changing anything.

See ZF 6HP gearbox types and controllers. Sources reviewed 17 November 2026.

Community fitting guideIn a 2017 Jaguar XF 6HP28 illustrated workshop thread, davetibbs describes removing and refitting the electronic unit and valve body, drawing attention to the locating dowels, parking-lock linkage and connector sleeve. This is an owner's worked example of that assembly, not evidence that the electronics carry Bosch 0260550043 or a substitute for the exact vehicle's service procedure. Confirm selector mechanism, parts and fastener information for the actual unit.The author discusses rebuilding the existing assembly; the report does not demonstrate a cross-vehicle TCM swap or prove software compatibility of another donor.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Bosch GS19.11 E-shift Jaguar ZF 6HP28 controller

GS19.11 is a control-unit designation used in selected ZF 6HP28 mechatronics. Jaguar shift-by-wire and Land Rover mechanical-shift versions must be identified separately.

ZF 6HP26 transmission cutaway
A ZF 6HP26 cutaway for family context; it is not a photograph identifying this controller or a Jaguar 6HP28. Ralf Pfeifer, Wikimedia Commons, CC BY-SA 3.0, unmodified.
ZF 6HP mechatronic electronic module and connector sleeve
Illustrative ZF 6HP mechatronic electronic module and connector sleeve, from ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission. This general image does not identify the controller part number or a Jaguar-specific unit.

Identification and examples

Jaguar specialist Old Jaguar lists Bosch 0260550043 / ZF 6058007115 for the GS19.11 E-shift 6HP28 and cites Jaguar X150, X250 and X351 examples. Its mechanical-shift Land Rover example lists different numbers, including Bosch 0260550041. The specialist's listing is not a guarantee of interchange: verify model year, engine, hardware and software ID, selector, VIN and gearbox specification.

A 2010 Jaguar XF 5.0 SC service description identifies a 6HP28 with integrated TCM/mechatronic, rotary selector and electronic park lock. It does not identify a Bosch number, so it is an application example, not proof that every 2010 XF uses 0260550043.

Jaguar 6HP26/28 shift-by-wire connector example

The 16-way gearbox connector assignments below are transcribed from William Henney's 6HP26 training presentation, specifically its “Jaguar 6HP26/28 with shift-by-wire” table. The presentation does not associate the table with a specific Bosch number or VIN and does not clearly state connector-face orientation. It gives a numbered connector photograph: check that and the actual VIN-specific wiring document and moulded cavity numbers before connecting. These are documented assignments for the described example, not independently bench-verified or a guaranteed pinout for this particular controller number. “Not used” applies to the source example only.

CavityFunction in source example
1Not used in source example
2CAN low
3ISO K (example application)
4Not used in source example
5Not used in source example
6CAN high
7Not used in source example
8LIN selector-position information
9Terminal 15 wake-up
10Park / no-park signal
11Not used in source example
12Not used in source example
13Terminal 31-1 ground
14Terminal 30 permanent positive
15Not used in source example
16Terminal 31-2 ground

The same presentation's mechanical-selector example has different functions at cavities 1, 4, 5 and 8. Do not transfer these values to mechanical-shift Jaguar, Land Rover, BMW or another car without its own wiring evidence.

Programming and recalibration

PCMflash lists Jaguar/Land Rover 6HP26/28 in module 81's manual, with reading, writing and checksum for specific TCM families. Magicmotorsport FLEX lists selected 6HP bench duplication in its duplicable units list; duplication alone does not prove calibration editing for this exact number. Check the current tool's vehicle, ECU identity, protocol and required licence. A calibration editor or service is separate from the device that reads and writes a file.

Use manufacturer-prescribed service configuration and a recovery plan when replacing the TCM. A compatible blank or used controller may require application-specific software and setup; match the vehicle and preserve its original identification and configuration before changing anything.

See ZF 6HP gearbox types and controllers. Sources reviewed 17 November 2026.

Revision 3: Bosch GS19.11 E-shift Jaguar ZF 6HP28 controller

GS19.11 is a control-unit designation used in selected ZF 6HP28 mechatronics. Jaguar shift-by-wire and Land Rover mechanical-shift versions must be identified separately.

ZF 6HP26 transmission cutaway
A ZF 6HP26 cutaway for family context; it is not a photograph identifying this controller or a Jaguar 6HP28. Ralf Pfeifer, Wikimedia Commons, CC BY-SA 3.0, unmodified.
ZF 6HP mechatronic electronic module and connector sleeve
Illustrative ZF 6HP mechatronic electronic module and connector sleeve, from ZF Aftermarket service information 50324. Credit ZF Friedrichshafen AG; reproduced with user-confirmed permission. This general image does not identify the controller part number or a Jaguar-specific unit.

Identification and examples

Jaguar specialist Old Jaguar lists Bosch 0260550043 / ZF 6058007115 for the GS19.11 E-shift 6HP28 and cites Jaguar X150, X250 and X351 examples. Its mechanical-shift Land Rover example lists different numbers, including Bosch 0260550041. The specialist's listing is not a guarantee of interchange: verify model year, engine, hardware and software ID, selector, VIN and gearbox specification.

A 2010 Jaguar XF 5.0 SC service description identifies a 6HP28 with integrated TCM/mechatronic, rotary selector and electronic park lock. It does not identify a Bosch number, so it is an application example, not proof that every 2010 XF uses 0260550043.

Jaguar 6HP26/28 shift-by-wire connector example

The 16-way gearbox connector assignments below are transcribed from William Henney's 6HP26 training presentation, specifically its “Jaguar 6HP26/28 with shift-by-wire” table. The presentation does not associate the table with a specific Bosch number or VIN and does not clearly state connector-face orientation. It gives a numbered connector photograph: check that and the actual VIN-specific wiring document and moulded cavity numbers before connecting. These are documented assignments for the described example, not independently bench-verified or a guaranteed pinout for this particular controller number. “Not used” applies to the source example only.

CavityFunction in source example
1Not used in source example
2CAN low
3ISO K (example application)
4Not used in source example
5Not used in source example
6CAN high
7Not used in source example
8LIN selector-position information
9Terminal 15 wake-up
10Park / no-park signal
11Not used in source example
12Not used in source example
13Terminal 31-1 ground
14Terminal 30 permanent positive
15Not used in source example
16Terminal 31-2 ground

The same presentation's mechanical-selector example has different functions at cavities 1, 4, 5 and 8. Do not transfer these values to mechanical-shift Jaguar, Land Rover, BMW or another car without its own wiring evidence.

Programming and recalibration

PCMflash lists Jaguar/Land Rover 6HP26/28 in module 81's manual, with reading, writing and checksum for specific TCM families. Magicmotorsport FLEX lists selected 6HP bench duplication in its duplicable units list; duplication alone does not prove calibration editing for this exact number. Check the current tool's vehicle, ECU identity, protocol and required licence. A calibration editor or service is separate from the device that reads and writes a file.

Use manufacturer-prescribed service configuration and a recovery plan when replacing the TCM. A compatible blank or used controller may require application-specific software and setup; match the vehicle and preserve its original identification and configuration before changing anything.

See ZF 6HP gearbox types and controllers. Sources reviewed 17 November 2026.

Community fitting guide

In a 2017 Jaguar XF 6HP28 illustrated workshop thread, davetibbs describes removing and refitting the electronic unit and valve body, drawing attention to the locating dowels, parking-lock linkage and connector sleeve. This is an owner's worked example of that assembly, not evidence that the electronics carry Bosch 0260550043 or a substitute for the exact vehicle's service procedure. Confirm selector mechanism, parts and fastener information for the actual unit.

The author discusses rebuilding the existing assembly; the report does not demonstrate a cross-vehicle TCM swap or prove software compatibility of another donor.