Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

RaceTech Dynamics markets the RTD Hub 2000 as a self-assembly hub dynamometer kit. It is offered for two- and four-wheel-drive configurations; the supplier describes mechanical components and eddy-current retarders while specifying third-party sensors and software separately. See Hub dynamometers and the manufacturers directory.

RaceTech Dynamics' RTD Hub product rendering. Image: RaceTech Dynamics, used with permission.

Company and model evidence

The supplier's product page identifies RTD Hub 2000 as a build-it-yourself system. The source does not establish a dated company or model history, so no founding or launch year is assumed. Verify current support, supply and specifications with the supplier.

Kit contents and working principle

The advertised two-unit package lists frame parts, two eddy-current retarders, rotating assemblies and hub-adapter sets. The four-unit kit lists four sets. A driven hub turns the connected assembly and retarder; the brake applies resistance electromagnetically when supplied and controlled through suitable electronics. The maker describes wheeled frames and CV-joint axles, but the complete installation still needs alignment and support checked according to its instructions.

The page lists maximum figures for the system but does not make a peak number an all-speed continuous rating. Confirm hub torque, hub speed, absorber power and thermal-duty curves for the exact 2WD or 4WD configuration, as well as vehicle attachment and support requirements.

Controls and commissioning

The supplier states that sensors and software are not included. Choose and integrate suitable speed sensors, load measurement, controller, brake power electronics and data-acquisition software; confirm which components, cables and instructions are included in the quoted kit. The control strategy and 4WD behaviour depend on the selected third-party system rather than a standard built-in controller specified by the cited page.

Assembly, safe support, guards, electrical protection, emergency response and speed and torque calibration must be verified as a complete system. A self-assembly mechanical kit should not be treated as a ready-to-run calibrated dynamometer. See Dynamometer control systems and test setup and safety.

Based on the supplier's published description checked 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: RaceTech Dynamics hub dyno kit

RaceTech Dynamics markets the RTD Hub 2000 as a self-assembly hub dynamometer kit. It is offered for two- and four-wheel-drive configurations; the supplier describes mechanical components and eddy-current retarders while specifying third-party sensors and software separately. See Hub dynamometers and the manufacturers directory.

RaceTech Dynamics rendering of a hub-dyno unit on a wheeled frame.
RaceTech Dynamics' RTD Hub product rendering. Image: RaceTech Dynamics, used with permission.

Company and model evidence

The supplier's product page identifies RTD Hub 2000 as a build-it-yourself system. The source does not establish a dated company or model history, so no founding or launch year is assumed. Verify current support, supply and specifications with the supplier.

Kit contents and working principle

The advertised two-unit package lists frame parts, two eddy-current retarders, rotating assemblies and hub-adapter sets. The four-unit kit lists four sets. A driven hub turns the connected assembly and retarder; the brake applies resistance electromagnetically when supplied and controlled through suitable electronics. The maker describes wheeled frames and CV-joint axles, but the complete installation still needs alignment and support checked according to its instructions.

The page lists maximum figures for the system but does not make a peak number an all-speed continuous rating. Confirm hub torque, hub speed, absorber power and thermal-duty curves for the exact 2WD or 4WD configuration, as well as vehicle attachment and support requirements.

Controls and commissioning

The supplier states that sensors and software are not included. Choose and integrate suitable speed sensors, load measurement, controller, brake power electronics and data-acquisition software; confirm which components, cables and instructions are included in the quoted kit. The control strategy and 4WD behaviour depend on the selected third-party system rather than a standard built-in controller specified by the cited page.

Assembly, safe support, guards, electrical protection, emergency response and speed and torque calibration must be verified as a complete system. A self-assembly mechanical kit should not be treated as a ready-to-run calibrated dynamometer. See Dynamometer control systems and test setup and safety.

Based on the supplier's published description checked 17 November 2026.

Revision 1: RaceTech Dynamics hub dyno kit

RaceTech Dynamics markets the RTD Hub 2000 as a self-assembly hub dynamometer kit. It is offered for two- and four-wheel-drive configurations; the supplier describes mechanical components and eddy-current retarders while specifying third-party sensors and software separately. See Hub dynamometers and the manufacturers directory.

RaceTech Dynamics rendering of a hub-dyno unit on a wheeled frame.
RaceTech Dynamics' RTD Hub product rendering. Image: RaceTech Dynamics, used with permission.

Company and model evidence

The supplier's product page identifies RTD Hub 2000 as a build-it-yourself system. The source does not establish a dated company or model history, so no founding or launch year is assumed. Verify current support, supply and specifications with the supplier.

Kit contents and working principle

The advertised two-unit package lists frame parts, two eddy-current retarders, rotating assemblies and hub-adapter sets. The four-unit kit lists four sets. A driven hub turns the connected assembly and retarder; the brake applies resistance electromagnetically when supplied and controlled through suitable electronics. The maker describes wheeled frames and CV-joint axles, but the complete installation still needs alignment and support checked according to its instructions.

The page lists maximum figures for the system but does not make a peak number an all-speed continuous rating. Confirm hub torque, hub speed, absorber power and thermal-duty curves for the exact 2WD or 4WD configuration, as well as vehicle attachment and support requirements.

Controls and commissioning

The supplier states that sensors and software are not included. Choose and integrate suitable speed sensors, load measurement, controller, brake power electronics and data-acquisition software; confirm which components, cables and instructions are included in the quoted kit. The control strategy and 4WD behaviour depend on the selected third-party system rather than a standard built-in controller specified by the cited page.

Assembly, safe support, guards, electrical protection, emergency response and speed and torque calibration must be verified as a complete system. A self-assembly mechanical kit should not be treated as a ready-to-run calibrated dynamometer. See Dynamometer control systems and test setup and safety.

Based on the supplier's published description checked 17 November 2026.