Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

This guide covers the 2008 UK Maserati GranTurismo M145 4.2-litre automatic identified on the supplied workshop diagnostic pages. The Maserati GranTurismo Academy training document identifies its gearbox as a ZF 6HP26: a six-speed electrohydraulic planetary automatic with a torque converter and lock-up clutch, controlled by an integrated mechatronic unit. It is different from the mechanically shifted Cambiocorsa/MC-Shift system. A shift paddle or the word “Sport” does not identify which transmission is fitted. Confirm the VIN, gearbox plate, controller and software before using any diagnostic data. Sources: 201140064-GranTurismo-En.pdf, supplied Maserati Academy training, PDF pp. 39–41, 54; GT 2008 UK/gen GEARBOX.pdf, workshop procedure 00.AB.020, PDF p. 1. These local manuals are not published here. A Maserati 2008 brochure also describes the six-speed ZF automatic.

What the NCA faults represent

The supplied GT 2008 UK/dtc/NCA Auto Gearbox.pdf, PDF pp. 1–3, is an error-selection list for the M145 automatic gearbox node (NCA), explicitly labelled GranTurismo 2008 United Kingdom 4200 cc automatic. It says the list shows faults the controller can detect and that the diagnostic tool displays those in memory. It does not establish fault frequency, the failure cause in a particular car, or a repair for each entry. Save all relevant control-unit codes and freeze-frame details before clearing them.

Listed exampleHow to use it
P0562/P0563, low/high supply voltage; U0001 or U0100, network/engine communicationCheck battery and charging condition, supply and grounds under relevant load, and associated network faults across the vehicle. A gearbox message caused by a supply or communication event does not automatically mean internal transmission failure.
P0710–P0714, ATF temperature signal or plausibility; P0716/P0717, turbine-input-speed plausibility or missing signalCapture the actual temperature and input-speed channels, operating conditions, fault status and circuit-specific test results. An implausible signal is not a direct measurement of fluid condition or proof that a sensor alone is faulty.
P0721/P0722 output-speed signal, P0730–P0736 incorrect ratios, P0781–P0784 or P0829 shift-selection errorsRecord gear request, reported gear, input/output speeds and when the event occurs. Verify speed inputs and applicable hydraulic/mechanical tests before attributing a ratio or shift error to a particular clutch or valve.
P0741 torque-converter plausibility; P2732–P2735 PR6 torque-converter pressure regulator entriesPreserve command, applicable converter slip, fluid temperature and associated faults. The list distinguishes plausibility and electrical/pressure-regulator entries; neither alone proves the torque converter needs replacement.
P0705–P0708 lever input or plausibility; P0571 brake-pedal status via CANCompare the driver's selector and brake actions with the states seen by NCA, using the specific vehicle's test plan. Look for switch, wiring, supply and network evidence as applicable.
P0897 oil deterioration/temperature; P0634 engine/gearbox temperature too highRecord the temperature channel and actual conditions, cooling-system history and other codes. Do not infer from a single entry that the oil level, sensor or cooler is the sole cause.

All code descriptions above are scoped to the supplied NCA list, not a generic mapping for every 6HP or Maserati. Use the linked diagnostic software's current guided test for this control unit. See also torque-converter clutch signals and diagnosis.

Leak and mechatronic service considerations

ZF’s service information 50638 EN identifies seal kits for several 6HP variants, including 6HP26. It explains that when mechatronics are removed, the required fill quantity changes and a seal kit is required in the operations it describes. Confirm the exact gearbox and Maserati service instructions: this is not a fluid quantity, a diagnosis of a leak or evidence that all versions use the same seal kit.

As a separate, explicitly BMW-specific example of why leak location must be verified, BMW service information B24 08 06 describes sealing-sleeve seepage on certain BMW 6HP applications and distinguishes surface wetness from evidence of substantial fluid loss. It does not establish that the bulletin, its thresholds or repair instructions apply to Maserati. If a GranTurismo shows oil around the transmission, identify the actual source and condition using the Maserati procedure; oil on or near the pan does not by itself prove the pan gasket or mechatronics are defective.

A repeatable diagnostic sequence

  1. Record the vehicle and gearbox identities, service history, warning, operating mode, temperature and conditions: a take-up event, one shift, lock-up in cruise or a fault present immediately at start. Save fault status and environmental data before clearing anything.
  2. Scan NCA and relevant engine, brake, body and other units. Compare supply voltage, network messages, brake and selector states and the chronology of related faults. The documented NCA list includes CAN data and communication faults as well as transmission-specific faults.
  3. With the correct test plan and safe conditions, compare commanded and actual gear, engine speed, turbine/input speed, output speed, torque-converter state and ATF temperature if the diagnostic tool exposes them. Channel definitions and sample rates matter; a speed difference alone is not proof of a failed converter.
  4. Inspect for leaks and assess service-fluid condition and the oil-to-coolant heat-exchanger circuit using current instructions for the exact vehicle. The supplied GT 2008 UK/GEARBOX OIL HEAT EXCHANGER.pdf, procedure 03.50.079, PDF pp. 1 and 3–5, describes this assembly, renews seals during the documented removal, and requires checks of gearbox oil level and engine cooling-system fill afterwards. It is not evidence that every overheating event comes from the exchanger.
  5. Test any fault-specific electrical, hydraulic or mechanical branch indicated by the evidence and the manufacturer sequence. Verify the original complaint and relevant states after repair; adaptations are not a substitute for identifying a defective component or low supply.

Stationary behaviour and service context

The Maserati Academy training describes a stationary disengagement strategy for this 6HP26 application under selected conditions: an internal clutch is opened to reduce converter load when the car is stopped. This describes a control strategy; it does not prove the strategy was active during any reported engagement delay. Source: supplied 201140064-GranTurismo-En.pdf, PDF p. 46.

The same training document describes a temperature-dependent ATF level-check process, and its figures and steps must be read in their complete vehicle and service context. Do not transfer a fill quantity, temperature, fluid or torque from another 6HP installation, assume a partial drain is a complete fill, or reset learned values as a first diagnostic step. Use the current Maserati procedure and equipment for the specific unit. ZF also provides manufacturer service information for its 5HP/6HP oil-change kits, subject to the applicable vehicle specification.

For an earlier Quattroporte example, the supplied 201140044-4P-GQ-en-07.pdf, PDF pp. 55–57 and 62, describes its own 6HP26 torque-converter automatic and integrated mechatronics. This establishes an additional documented application, not identical calibrations, DTCs, model-year coverage or repairs. See the related Maserati Cambiocorsa/F1 guide and ZF 6HP/8HP diagnosis.