Eaton Cummins UltraShift PLUS is a family of heavy- and medium-duty automated manual transmissions. The TRTS0940 troubleshooting guide, dated 19 July 2024, covers specified UltraShift PLUS models with a transmission electronic control unit (TECU), electronic clutch actuator (ECA) and electronically controlled shifting. This is a commercial-vehicle example, not an application of the passenger-car codes or hydraulic procedures in the other guides. Confirm the transmission model, software, actuator generation, vehicle equipment and current manufacturer instructions.
Clutch, shifting and feedback
The TECU coordinates clutch actuation and gear changes. TRTS0940 identifies separate electrical pretests and fault-isolation branches for generation 1 and generation 2 electronic clutch actuators; follow the identification procedure in the applicable edition rather than assuming they are electrically interchangeable. The same guide lists rail and gear motors, speed sensors, range and splitter components, and vehicle network messages. Which components and diagnostics apply depends on the transmission and vehicle.
A clutch actuator complaint may involve the actuator, supply, communications, speed feedback or mechanical clutch and release hardware. The Eaton generation 1 fault-code 65 guideline describes an ECA speed signal used as a secondary engine-speed signal when the J1939 engine-speed signal is unavailable. That function and its specific diagnostic branches must not be assumed for a different actuator generation.
Fault examples and useful evidence
| TRTS0940 example | Diagnostic direction |
|---|---|
| Fault 16 or 19, ECA communications | Record the complete fault, FMI, active/inactive status and related supply or network faults; select the correct actuator-generation test. An unavailable message alone does not prove the actuator has failed. |
| Fault 26, clutch slip; fault 27, clutch disengagement | Record the operation and conditions and follow the specified symptom and fault-isolation procedure. Clutch condition, release mechanism and actuator feedback require separate evidence. |
| Fault 64, ECA; fault 65, ECA speed sensor | Use the correct generation and FMI branch. Eaton's generation 1 code-65 guideline distinguishes sensor/harness conditions and warns that sensor location differs between designs. |
| Fault 66 or 67, ECA battery or ignition voltage | Check the exact pretest and supply path under the manufacturer's conditions; an actuator warning need not mean an internally defective actuator. |
| Fault 41/43, range engagement or range solenoid | Record which range and operating conditions are affected. Eaton's fault 43 guideline identifies wiring and solenoid circuit faults as possible branches, not a universal part verdict. |
Fault numbers above refer to the Eaton guide's own numbering, not generic OBD P-codes. Failure mode identifiers, vehicle, actuator generation, software and active status matter. The TRTS0940 guide provides separate tests and prerequisites; a code label alone is not a repair instruction.
Documented release-bearing and handling faults
Eaton bulletin CLIB0030 describes a release-bearing failure associated with incompatible service grease in specified ECA clutch part families used with UltraShift PLUS and Fuller Advantage automated transmissions. For the bulletin's documented failure mode it relates fault 27 FMI 7 to the clutch inertia-brake touch-point result and calls for both diagnostic and physical evidence. The same base fault has other possible causes; use the correct current fault tree and bulletin for the particular clutch, not that historical threshold as a universal diagnosis. Check the current approved lubricant for the actual part; the bulletin notes that some greases meeting an earlier broad specification were still incompatible.
Eaton's separate CLIB-0020 warns that removing a covered ECA clutch without its specified caging bolts can permanently damage it and lead to release or engagement faults if reinstalled. Determine the clutch part and service history and follow the current manufacturer removal procedure; do not infer that every fault 27 was caused by removal damage.
Diagnose and verify
- Record the driver's complaint, current gear and mode, operating temperature and load, recent clutch or electrical work and complete faults including FMI, status, occurrence counts and time stamps where available.
- Use the specified diagnostic procedure and the correct ECA-generation electrical pretest. Compare battery and ignition supply, connector condition, actuator feedback, speed signals and network faults where the test plan directs.
- When evidence points to a clutch-release fault, consider the release mechanism as well as the actuator. A Peterbilt service bulletin 23-003 documents broken clutch levers on a defined build population with specified engines and Eaton transmissions; it does not make every release problem a broken lever. Check current VIN-specific service information.
- After an established repair, follow the correct installation, calibration and verification procedure. Eaton's UltraShift PLUS PV installation guide notes that fault 27 and fault 68 can appear at the initial power-up stage of that installation before its specified clutch and grade-sensor setup; this is not an explanation for the same codes on every vehicle in service.
For the separate Endurant HD and specified PACCAR TX-12 family, see Endurant HD faults and diagnosis; its linear actuator and fault-code procedures must not be assumed to apply to UltraShift PLUS.
For a separate commercial-vehicle design, see Volvo Trucks I-Shift operation and diagnosis. Its faults and service procedures must not be transferred to Eaton equipment.
Secure the vehicle and follow the manufacturer's safety instructions before active tests or work around a clutch or shifting mechanism; some functions can move automatically. See automated manual clutch control and the electronic gearbox guide.