Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

This guide interprets a 2019 UK Maserati Quattroporte M156 3.0 TDS V6, 275 hp, two-wheel-drive automatic diagnostic-menu example. The supplied M018 Transmission Control Module (TCM) — Errors document identifies that vehicle and presents possible fault entries, not an actual car's stored codes or a complete repair procedure. Source: local resource QTP M156 2017-2020 Diesel 3.0 / errors / tcm.pdf, PDF pp. 1–5. Verify VIN, gearbox and controller identity and use the current diagnostic tree for the vehicle under test.

Maserati's MY19 Quattroporte press kit identifies an eight-speed ZF automatic for the documented model range. This is a separate system from the earlier M139/M145 Cambiocorsa automated manual; their clutch, hydraulic and learning procedures must not be interchanged. The press information alone does not identify the exact gearbox variant or TCU software for an individual car.

What the menu does and does not say

The document explains that the menu lists errors the controller can potentially record, while a diagnostic session shows the errors actually stored in the ECU. It directs the user to save or print the fault memory first, and describes separate help, wiring and guided-diagnosis views. The supplied PDF is a local reference; it is not a transcript of a faulting vehicle or the contents of those linked procedures. A fault label is the controller's reported condition, not proof that a named component must be replaced.

Examples worth separating

Menu exampleDiagnostic directionLimit P0562-00 — system voltage low; P0563-00 — high (p. 1)Record battery and supply conditions and other control-unit faults before clearing memory; investigate using the applicable guided test.A low-voltage event can coexist with another fault; the menu does not establish which source caused it. P0716-00 — input-shaft speed performance; P0721-00 — output-shaft speed performance (p. 1)Compare the diagnostic channels and operating conditions for engine, input and output speeds as defined by the tool.The list does not supply a sensor acceptance limit, wiring diagram or a universal speed conversion. P0731-00 — gear 1 incorrect ratio; P07D9-00 — gear 8 incorrect ratio (pp. 1–2)Record commanded and actual gear, relevant speed signals, fluid temperature and when the discrepancy occurs.A ratio fault describes a detected discrepancy, not by itself proof of a failed gear or clutch pack. P0960-00 — pressure control solenoid 1 circuit/open (p. 2)Follow the exact circuit test, checking supply and connections as directed.A circuit description does not identify a hydraulic pressure value or prove a failed valve. P1DB7-00 — torque converter clutch performance (p. 4)Record the converter operating state and relevant input/engine-speed channels during the event where available.The list does not specify an allowable slip or establish the cause; see converter-clutch signal interpretation. U0100-00 — lost engine-controller communication; U0103-00 — lost electric gear-shift module communication (p. 4)Read other relevant controllers and record communication and supply faults together.A communication fault does not by itself prove that the named controller is defective.

These names and suffixes are transcribed from the supplied M018 menu for the stated vehicle. The same base code can have a different context, suffix, enabling condition or guided test in other systems.

Related recall on a different engine and model year

A separate US recall, 18V173 / Maserati campaign 365, concerned specified 2017 Quattroporte V6 and Ghibli vehicles. Maserati described an engine-control software defect that could cause an unexpected shift to neutral or park, or an engine stall, at very low speed; the recall remedy was an engine-control software update. This is useful evidence that an apparent gearbox complaint can originate in another control system, but the recall does not establish that the 2019 UK diesel described above is affected. Verify VIN, market, powertrain and campaign status before applying any recall information.

Practical sequence

Capture the complete fault report, status and freeze-frame/environmental data if the tool provides them. Record software identity, prior repairs, battery events, exact symptom, temperature and gear or selector position. Separate a selector request or electrical supply complaint from a driving ratio, speed signal or converter-lockup complaint. Check the signal definitions in the diagnostic tool before comparing values. Use the vehicle-specific guided test and wiring information for the stored fault. Compare related powertrain, ABS and selector faults rather than assuming a menu entry diagnoses one part. After a confirmed repair, follow the current service information for any reset or adaptation and verify the original complaint in the prescribed conditions. This PDF does not provide an adaptation sequence, fluid specification or replacement threshold.

See Quattroporte generations and engines and the broader gearbox and transmission catalogue. Do not transfer these observations to other Quattroporte years, markets, engines or gearbox variants without matching the service data.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Maserati Quattroporte M156 diesel automatic TCM diagnosis

This guide interprets a 2019 UK Maserati Quattroporte M156 3.0 TDS V6, 275 hp, two-wheel-drive automatic diagnostic-menu example. The supplied M018 Transmission Control Module (TCM) — Errors document identifies that vehicle and presents possible fault entries, not an actual car's stored codes or a complete repair procedure. Source: local resource QTP M156 2017-2020 Diesel 3.0 / errors / tcm.pdf, PDF pp. 1–5. Verify VIN, gearbox and controller identity and use the current diagnostic tree for the vehicle under test.

Maserati's MY19 Quattroporte press kit identifies an eight-speed ZF automatic for the documented model range. This is a separate system from the earlier M139/M145 Cambiocorsa automated manual; their clutch, hydraulic and learning procedures must not be interchanged. The press information alone does not identify the exact gearbox variant or TCU software for an individual car.

What the menu does and does not say

The document explains that the menu lists errors the controller can potentially record, while a diagnostic session shows the errors actually stored in the ECU. It directs the user to save or print the fault memory first, and describes separate help, wiring and guided-diagnosis views. The supplied PDF is a local reference; it is not a transcript of a faulting vehicle or the contents of those linked procedures. A fault label is the controller's reported condition, not proof that a named component must be replaced.

Examples worth separating

Menu exampleDiagnostic directionLimit
P0562-00 — system voltage low; P0563-00 — high (p. 1)Record battery and supply conditions and other control-unit faults before clearing memory; investigate using the applicable guided test.A low-voltage event can coexist with another fault; the menu does not establish which source caused it.
P0716-00 — input-shaft speed performance; P0721-00 — output-shaft speed performance (p. 1)Compare the diagnostic channels and operating conditions for engine, input and output speeds as defined by the tool.The list does not supply a sensor acceptance limit, wiring diagram or a universal speed conversion.
P0731-00 — gear 1 incorrect ratio; P07D9-00 — gear 8 incorrect ratio (pp. 1–2)Record commanded and actual gear, relevant speed signals, fluid temperature and when the discrepancy occurs.A ratio fault describes a detected discrepancy, not by itself proof of a failed gear or clutch pack.
P0960-00 — pressure control solenoid 1 circuit/open (p. 2)Follow the exact circuit test, checking supply and connections as directed.A circuit description does not identify a hydraulic pressure value or prove a failed valve.
P1DB7-00 — torque converter clutch performance (p. 4)Record the converter operating state and relevant input/engine-speed channels during the event where available.The list does not specify an allowable slip or establish the cause; see converter-clutch signal interpretation.
U0100-00 — lost engine-controller communication; U0103-00 — lost electric gear-shift module communication (p. 4)Read other relevant controllers and record communication and supply faults together.A communication fault does not by itself prove that the named controller is defective.

These names and suffixes are transcribed from the supplied M018 menu for the stated vehicle. The same base code can have a different context, suffix, enabling condition or guided test in other systems.

Related recall on a different engine and model year

A separate US recall, 18V173 / Maserati campaign 365, concerned specified 2017 Quattroporte V6 and Ghibli vehicles. Maserati described an engine-control software defect that could cause an unexpected shift to neutral or park, or an engine stall, at very low speed; the recall remedy was an engine-control software update. This is useful evidence that an apparent gearbox complaint can originate in another control system, but the recall does not establish that the 2019 UK diesel described above is affected. Verify VIN, market, powertrain and campaign status before applying any recall information.

Practical sequence

  1. Capture the complete fault report, status and freeze-frame/environmental data if the tool provides them. Record software identity, prior repairs, battery events, exact symptom, temperature and gear or selector position.
  2. Separate a selector request or electrical supply complaint from a driving ratio, speed signal or converter-lockup complaint. Check the signal definitions in the diagnostic tool before comparing values.
  3. Use the vehicle-specific guided test and wiring information for the stored fault. Compare related powertrain, ABS and selector faults rather than assuming a menu entry diagnoses one part.
  4. After a confirmed repair, follow the current service information for any reset or adaptation and verify the original complaint in the prescribed conditions. This PDF does not provide an adaptation sequence, fluid specification or replacement threshold.

See Quattroporte generations and engines and the broader gearbox and transmission catalogue. Do not transfer these observations to other Quattroporte years, markets, engines or gearbox variants without matching the service data.

Revision 2: Maserati Quattroporte M156 diesel automatic TCM diagnosis

This guide interprets a 2019 UK Maserati Quattroporte M156 3.0 TDS V6, 275 hp, two-wheel-drive automatic diagnostic-menu example. The supplied M018 Transmission Control Module (TCM) — Errors document identifies that vehicle and presents possible fault entries, not an actual car's stored codes or a complete repair procedure. Source: local resource QTP M156 2017-2020 Diesel 3.0 / errors / tcm.pdf, PDF pp. 1–5. Verify VIN, gearbox and controller identity and use the current diagnostic tree for the vehicle under test.

Maserati's MY19 Quattroporte press kit identifies an eight-speed ZF automatic for the documented model range. This is a separate system from the earlier M139/M145 Cambiocorsa automated manual; their clutch, hydraulic and learning procedures must not be interchanged. The press information alone does not identify the exact gearbox variant or TCU software for an individual car.

What the menu does and does not say

The document explains that the menu lists errors the controller can potentially record, while a diagnostic session shows the errors actually stored in the ECU. It directs the user to save or print the fault memory first, and describes separate help, wiring and guided-diagnosis views. The supplied PDF is a local reference; it is not a transcript of a faulting vehicle or the contents of those linked procedures. A fault label is the controller's reported condition, not proof that a named component must be replaced.

Examples worth separating

Menu exampleDiagnostic directionLimit
P0562-00 — system voltage low; P0563-00 — high (p. 1)Record battery and supply conditions and other control-unit faults before clearing memory; investigate using the applicable guided test.A low-voltage event can coexist with another fault; the menu does not establish which source caused it.
P0716-00 — input-shaft speed performance; P0721-00 — output-shaft speed performance (p. 1)Compare the diagnostic channels and operating conditions for engine, input and output speeds as defined by the tool.The list does not supply a sensor acceptance limit, wiring diagram or a universal speed conversion.
P0731-00 — gear 1 incorrect ratio; P07D9-00 — gear 8 incorrect ratio (pp. 1–2)Record commanded and actual gear, relevant speed signals, fluid temperature and when the discrepancy occurs.A ratio fault describes a detected discrepancy, not by itself proof of a failed gear or clutch pack.
P0960-00 — pressure control solenoid 1 circuit/open (p. 2)Follow the exact circuit test, checking supply and connections as directed.A circuit description does not identify a hydraulic pressure value or prove a failed valve.
P1DB7-00 — torque converter clutch performance (p. 4)Record the converter operating state and relevant input/engine-speed channels during the event where available.The list does not specify an allowable slip or establish the cause; see converter-clutch signal interpretation.
U0100-00 — lost engine-controller communication; U0103-00 — lost electric gear-shift module communication (p. 4)Read other relevant controllers and record communication and supply faults together.A communication fault does not by itself prove that the named controller is defective.

These names and suffixes are transcribed from the supplied M018 menu for the stated vehicle. The same base code can have a different context, suffix, enabling condition or guided test in other systems.

Related recall on a different engine and model year

A separate US recall, 18V173 / Maserati campaign 365, concerned specified 2017 Quattroporte V6 and Ghibli vehicles. Maserati described an engine-control software defect that could cause an unexpected shift to neutral or park, or an engine stall, at very low speed; the recall remedy was an engine-control software update. This is useful evidence that an apparent gearbox complaint can originate in another control system, but the recall does not establish that the 2019 UK diesel described above is affected. Verify VIN, market, powertrain and campaign status before applying any recall information.

Practical sequence

  1. Capture the complete fault report, status and freeze-frame/environmental data if the tool provides them. Record software identity, prior repairs, battery events, exact symptom, temperature and gear or selector position.
  2. Separate a selector request or electrical supply complaint from a driving ratio, speed signal or converter-lockup complaint. Check the signal definitions in the diagnostic tool before comparing values.
  3. Use the vehicle-specific guided test and wiring information for the stored fault. Compare related powertrain, ABS and selector faults rather than assuming a menu entry diagnoses one part.
  4. After a confirmed repair, follow the current service information for any reset or adaptation and verify the original complaint in the prescribed conditions. This PDF does not provide an adaptation sequence, fluid specification or replacement threshold.

See Quattroporte generations and engines and the broader gearbox and transmission catalogue. Do not transfer these observations to other Quattroporte years, markets, engines or gearbox variants without matching the service data.