Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

This guide concerns Aston Martin V8 Vantage and V8 Vantage S examples with six- or seven-speed SportShift automated manual (ASM) transmissions. The system operates the clutch and gear changes for the driver; exact hardware, controller software and procedures depend on the vehicle. It is separate from the AMShift manual-transmission feature described for other Aston Martin applications. Identify VIN, market, engine, transmission and control software before diagnosis. Aston Martin SB-07-0315V4; Aston Martin AMShift introduction.

Driveability and learning

Aston Martin's 2017 SportShift clutch driveability bulletin covers specified V8 Vantage and Vantage S six- and seven-speed ASM examples. It notes that clutches had sometimes been replaced unnecessarily and calls for diagnosis of faults, software and clutch-control behaviour before deciding on repair. Its examples include overheat warnings, unsatisfactory shifts, gear disengagement and poor low-speed response; none proves by itself that a clutch disc is worn.

The bulletin describes a cold-start clutch self-diagnosis and learning interval in its covered system. It says that on certain Vantage S vehicles the N button LED flashes while this runs. Treat this as a documented model- and software-specific behaviour, not a universal wait time or interpretation for every Aston Martin.

The same bulletin compares the requested clutch position and actual clutch stroke, and records learned values, coolant temperature, engine and clutch speeds. These are useful diagnostic distinctions: a displayed wear index or kiss point is learned data, not a direct measurement of remaining lining thickness. Use the current diagnostic plan and its prerequisites; do not erase statistics, reprogram or run a learn routine just to make a number look better.

Two distinct recall examples

  • Six-speed hydraulic connector: Aston Martin RA-07-0023 / US recall 17V390 covers a defined VIN population of V8 Vantage six-speed SportShift vehicles produced in October–November 2011. It describes a connector failure that can cause hydraulic-fluid loss and gear-selection problems. Confirm VIN and repair completion with the manufacturer; a leak on another vehicle does not prove recall applicability.
  • Seven-speed hydraulic connector: A separate US recall, 17V391 / RA-07-0024, covers specified 2011–2014 V8 Vantage vehicles with seven-speed SportShift II, manufactured from 25 November 2010 to 13 September 2013. Aston Martin reported that insufficient support for the connector between the clutch-fluid pipe and ASM hydraulic system could allow it to fail, lose fluid and cause clutch malfunction. The VIN range is non-sequential: confirm the individual vehicle and completed remedy with Aston Martin. This is separate from the six-speed connector campaign and the seven-speed software campaign.
  • Seven-speed software and learning: RA-07-0022 concerns a defined non-US population of seven-speed SportShift II vehicles produced in the bulletin's July 2010–August 2012 range. It describes incompatible stored clutch adaptations after an earlier software action and possible unintended neutral selection or clutch slip. The recall's VIN and market scope are essential; check current campaign status rather than assuming all SportShift cars are affected.

Diagnostic approach

  1. Preserve the fault report, software identification, clutch and repair history, warning, selected/actual gear, mode, coolant temperature and the conditions in which the symptom occurs.
  2. Follow the current manufacturer's fault tree for the relevant stored codes; compare clutch request with feedback, relevant speeds, hydraulic condition, supply and related inputs where supported. A code, leak or shift complaint alone does not establish a single failed component.
  3. Check applicable service campaigns by VIN and market. Investigate hydraulic fluid loss and low pressure using the exact workshop procedures and test conditions. The accumulator and actuator can remain hazardous after ignition-off.
  4. After a confirmed repair, follow the precise current model-specific programming, bleeding and learning requirements, including prerequisites and safe vehicle restraint. Some active routines move components. Verify the original symptom afterwards; a generic reset cannot repair worn parts or a leak.

See automated clutch and gearshift control and the electronic gearbox guide.