Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Honda's i-SHIFT is an electronically automated manual transmission, not a conventional torque-converter automatic or a dual-clutch gearbox. This guide uses two separate documented examples: Honda's engineering description of the new Civic i-SHIFT, and a 2009 Jazz service-manual reproduction. Identify the model, market, transmission, control unit and software before applying a fault definition or learning procedure; the examples do not establish identical service details across all Civics and Jazzes. Honda R&D: Civic i-SHIFT development; Honda Jazz 2009 service-manual identification.

Layout and operation

Honda's Civic paper describes a six-speed manual-based gearbox with separate control of clutch, gear selection and gear shift. An electric motor generates hydraulic pressure for clutch release; the gear-change mechanism uses electric motor drive. The paper describes a self-adjusting friction clutch. This does not imply that the Civic uses the same hydraulic pump-and-accumulator architecture as an Alfa Selespeed, or that every Honda i-SHIFT component is interchangeable. The controller uses engine, brake and wheel-speed information while coordinating take-up and shifts. Honda R&D: system configuration and actuators.

The 2009 Jazz identification page lists SF7M i-SHIFT alongside different manual and automatic transmission options for specific markets and engine combinations. The name on a selector or the absence of a clutch pedal is not sufficient to select a repair procedure. Honda Jazz service-manual reproduction: transmission identification.

Record the event and fault data

Record the VIN, transmission and TCM identity, prior clutch or actuator repairs, warning lights, fault status and conditions: starting, selection of first or reverse, moving off, one particular shift, cold or hot, and brake/door state. Capture all relevant TCM, engine and other control-unit fault data before clearing anything. Compare commanded and actual gear and clutch actuator position, selector and brake inputs, supply voltage and engine or gearbox speed where the correct diagnostic equipment exposes them. Check the channel definitions and test conditions for that vehicle.

In the documented Jazz service-manual self-diagnosis, repeated detections of the same DTC are retained as one entry, and disconnecting the battery does not clear its EEPROM-stored codes. Its i-SHIFT warning can also be associated with abnormal supply voltage, so test power and ground under the specified conditions rather than treating the warning as proof of a failed actuator. These details are for that service-manual example. Honda Jazz i-SHIFT self-diagnosis.

Fault patterns and diagnostic branches

Documented exampleUseful distinction
2009 Jazz service-manual P0810The listed monitor describes a clutch position signal that does not change when the actuator is commanded. Check the applicable actuator, feedback, power, wiring and mechanical/hydraulic release tests; the code does not prove that a particular actuator assembly or clutch is defective.
2009 Jazz P0904 / P0914The chart distinguishes select and shift signal circuit conditions. Use the matching controller's wiring and test plan; a signal fault and a physically blocked gearbox selector are different possibilities.
2009 Jazz no drive to wheelsThe symptom tree checks the brake-switch state, indicated gear, clutch-line/reservoir condition and the clutch/release system before later active tests. This is a diagnostic sequence for its stated application, not a generic instruction to run learning or replace a controller.
2006 Civic five-door difficulty selecting gearsHonda service news reports that a foreign object near the transmission select lever can interfere with selection and may produce P0919 or P0909 on i-SHIFT cars. Honda says the symptom may change with vehicle acceleration or braking. Check the actual lever area using the appropriate procedure, but do not conclude that these codes always mean debris.

Sources: Honda Jazz i-SHIFT DTC chart; Honda Jazz no-drive symptom tree; Honda service news HUK00000000844, 2006 Civic five-door.

Jazz P0910 and brake-signal P0504

For the Jazz i-SHIFT described in Honda's workshop information, P0910 identifies a select actuator motor system malfunction. The diagnostic tree distinguishes an actuator that moves smoothly with its linkage disconnected from one that does not, then checks its electrical command and wiring before reaching a component conclusion. Follow the applicable manual and its conditions; movement tests can operate the mechanism and are not a simple code-based instruction to replace the actuator. Honda Jazz P0910 troubleshooting.

The same Jazz fail-safe index describes P0504 in terms of brake information received over F-CAN not changing through specified drive cycles, with manual-mode driving disabled. If this code is present, examine the brake input and the received communication data using the correct diagnostic procedure; manual-mode loss alone does not prove a brake switch fault. Honda Jazz i-SHIFT fail-safe index.

Learning and service

The Jazz service information distinguishes static and dynamic i-SHIFT learning with Honda diagnostic equipment. Its service matrix prescribes different modes for different work: for example, clutch disc or pressure-plate replacement is associated with dynamic learning, while removal or installation of the transmission is associated with static learning in that manual. Dynamic learning has different steps and includes a driving phase; an incomplete learning process can limit operation. This is not a universal recipe for another i-SHIFT vehicle. Honda Jazz service-manual reproduction: i-SHIFT learning.

Do not start active tests or erase learned values as a substitute for investigating a supply, hydraulic, wiring or mechanical fault. Actuators can move during testing; use the exact current Honda repair instructions, safety precautions and supported diagnostic tool. After a confirmed repair, perform the specified learning and verification under its prescribed conditions.

See automated manual clutch and shift control, Toyota MultiMode and the electronic gearbox guide.