Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 5

Removed text is struck through; added text is highlighted.

PEREK supplies dynamometer data acquisition, controllers and brake interfaces for new builds and retrofits. Its systems can be configured for engine, rolling-road and hub installations; the controller and power electronics must be matched to the existing dynamometer hardware. See Dynamometers and the manufacturers directory.

PEREK DC2 controller. Image: PEREK DC2 product page, used with permission.

History and role

Ronald Perek states that he founded PEREK in 2019 after mechatronics and electronics work at ECUMASTER. The company describes its work as dyno measurement and control, including upgrades of existing equipment from other makers. A conversion can retain the original frame and brake while changing controller components; the dyno's name does not necessarily identify the controller fitted today. PEREK: company and applications.

Systems and applications

PEREK describes its controller system for inertial and braked engine, chassis, hub and power-take-off dynos. Its peripheral guide specifies different speed-sensor counts for different layouts and identifies the separate absorber, load cell and brake supply needed for an absorption dyno. PEREK lists partner builders for complete machines; these are distinct companies, not PEREK dyno model names.

Controller and brake-interface models

DC1E4: an earlier controller identified by PEREK in documented retrofit examples, including a Bosch FLA206 upgrade.DC2: an integrated computer and controller; the maker lists support for unsynchronised 4WD chassis and 4WD hub systems with appropriate peripherals.DC2L: a lower-specification DC2-series variant for less complex applications, including mechanically synchronised 4WD chassis systems.BD3.1: an eddy-current brake power interface. Its electrical supply and brake compatibility must be checked for the installation.

The DC2 specification distinguishes the two variants and identifies the DC2 as a development of the earlier DC1E4. Dyno2 software supplies test display, recording and analysis; exact operating modes depend on the complete configured system.

Checking a retrofit

Record brake model, torque and speed limits, controller, software, power supply, sensor scaling, calibration and interlock arrangements. A capable controller cannot make an absorber motor a shaft or operate safely beyond its own cooling and mechanical limits. See dynamometer control systems.

DC2 and DC2L: hardware and applicationsBoth DC2-series controllers combine a computer and real-time acquisition/control hardware in one enclosure; a separate external PC is not required for normal local operation, although a screen and input devices are needed. PEREK identifies DC2 as an upgrade of the earlier DC1E4. Its full specification distinguishes the versions:FeatureDC2LDC2 ConfigurationInertia or braked engine, motorcycle and 2WD chassis dynos; mechanically synchronised 4WD chassis dyno.Also supports unsynchronised 4WD chassis and two- or four-wheel hub dynos, with up to four absorber units as configured. Load-cell inputsOne direct input with built-in amplifier.Four direct inputs with built-in amplifiers. Frequency inputsOne frequency input plus one multi-sensor engine-speed input.Five frequency inputs plus one multi-sensor engine-speed input. Analogue channelsOne fast 0–5 V input and four high-precision single-ended inputs, the latter also usable as two differential channels.Twelve fast 0–5 V inputs and eight high-precision single-ended inputs, the latter also usable as four differential channels. Outputs and CANOne analogue output, two low-side PWM outputs, one relay and one CAN bus.Four analogue outputs, four low-side and four high-side PWM outputs, four relays and two CAN buses.Input count is not the same as the number of complete dyno channels in every installation: a brake channel also requires a suitable speed pickup, load cell, appropriate power stage, wiring and configuration. The peripherals guide lists one speed sensor for a typical 2WD chassis or mechanically synchronised 4WD setup, two for an unsynchronised 4WD chassis or 2WD hub dyno, and four for a 4WD hub dyno.Brake power and sensor interfacesThe controller sends a low-power demand signal; an eddy-current brake needs a correctly rated external power stage to supply its coil. PEREK's retrofit guide describes compatible PWM and configurable analogue commands and says an existing compatible power stage may be reusable. It identifies BD2 and BD3 interface families, and the manufacturer describes BD3.1 as a CAN-controlled eddy-brake supply with fast demagnetisation. Verify brake-coil voltage, current, supply and control compatibility rather than assuming any old unit will work.The same retrofit guide distinguishes DC1-series load-cell signal amplification, which can use a suitable existing amplifier or an LCA1, from DC2's built-in programmable load-cell amplifiers. It describes Hall/toothed-wheel and encoder options; a variable-reluctance sensor may need the specified adapter when used on a general frequency input. Reuse depends on the sensor, signal and power specifications. A wideband oxygen probe normally needs its own compatible lambda controller before its signal is read by the dyno.Dyno2 software and controlDyno2 supports live plots, configurable sensor scaling, run comparisons, calibration tools, CSV export, CAN data and programmable auxiliary outputs. The manufacturer describes constant-power, RPM-lock, RPM-limit and sequence modes; the system overview additionally lists steady speed, ramp, programmable acceleration and road simulation. Available functions depend on the controller, firmware, peripherals and physical dyno. Correction factors use measured or entered ambient conditions; a calculated engine-power estimate remains distinct from directly measured hub or wheel output.Example: Dynocom AWD retrofitPEREK documents a Dynocom DYNO X AWD conversion using a DC1E4, two BD3 eddy-brake supplies, two replacement load cells with LCA1 amplifiers, and speed wheels and pickups. The account also describes load-cell and inertia calibration, PID setup, and fan and wheelbase control. This illustrates a particular installed conversion, not a guarantee that another Dynocom will have the same brake, wiring or reuse options.

Details are based on the linked company documentation checked 17 November 2026; verify present configurations and support with the supplier.

Additional output and sensor compatibilityOutputs can control compatible external power electronics or actuators using suitable PWM, 0–10 V or CAN commands; PEREK also specifies direct PWM up to 3 A where applicable. A high-current eddy-current absorber generally needs a matched brake power supply. The sensor requirement rises with independently rotating shafts: the peripheral guide lists two speed sensors for a 2WD hub setup and four for a 4WD hub setup. Electronic synchronisation has limits and must suit the vehicle and dyno.BD3 and BD3.1 eddy-brake power suppliesThe BD3/BD3.1 manual describes a separate mains-supplied eddy-current interface with closed-loop brake-current control, fast demagnetisation and CAN diagnostics such as current and power-stage temperature. PEREK lists single- or three-phase supply possibilities and different current ratings and duty limits; match the exact variant, supply, cooling and absorber coil rating. The brake and its power stage, not the DC controller alone, set the available loading.BD3.1 differs from BD3 in its cooling and power-supply arrangement and removes the earlier PWM input; do not assume both variants accept the same control signals. The manual describes CAN control for BD3.1. Observe the manufacturer's isolation, capacitor-discharge, installation and emergency procedures.Dyno2 control, logging and automationDyno2 supports calibration tools, graphs and run comparison, channels from compatible CAN and OBD equipment, configurable reports and CSV export. PEREK lists modes including RPM lock, constant power, RPM limit and test sequences; availability and usable control depend on the installed hardware and configuration. The run-tab guide also describes manual absorber demand and speed and acceleration control.In a documented control architecture, the speed loop compares measured and desired speed; a torque loop can then use load-cell feedback to request brake output. A separate position loop can use analogue feedback for a water valve or throttle actuator. PEREK states that these real-time control loops run at 1,000 Hz, whereas an optional software function PID runs at 100 Hz; these are loop update rates, not a guarantee of complete machine response or accuracy. See control-loop documentation.The manufacturer describes configurable CAN channels, remote-control inputs and test sequences. These features require correct signal, actuator and safety configuration. Dyno2 remote control; retrofitting guidance.Related comparison: Compare factory and aftermarket dynamometer controllers.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: PEREK dynamometer controllers

PEREK supplies dynamometer data acquisition, controllers and brake interfaces for new builds and retrofits. Its systems can be configured for engine, rolling-road and hub installations; the controller and power electronics must be matched to the existing dynamometer hardware. See Dynamometers and the manufacturers directory.

PEREK DC2 dynamometer controller and connection terminals.
PEREK DC2 controller. Image: PEREK DC2 product page, used with permission.

History and role

Ronald Perek states that he founded PEREK in 2019 after mechatronics and electronics work at ECUMASTER. The company describes its work as dyno measurement and control, including upgrades of existing equipment from other makers. A conversion can retain the original frame and brake while changing controller components; the dyno's name does not necessarily identify the controller fitted today. PEREK: company and applications.

Systems and applications

PEREK describes its controller system for inertial and braked engine, chassis, hub and power-take-off dynos. Its peripheral guide specifies different speed-sensor counts for different layouts and identifies the separate absorber, load cell and brake supply needed for an absorption dyno. PEREK lists partner builders for complete machines; these are distinct companies, not PEREK dyno model names.

Controller and brake-interface models

  • DC1E4: an earlier controller identified by PEREK in documented retrofit examples, including a Bosch FLA206 upgrade.
  • DC2: an integrated computer and controller; the maker lists support for unsynchronised 4WD chassis and 4WD hub systems with appropriate peripherals.
  • DC2L: a lower-specification DC2-series variant for less complex applications, including mechanically synchronised 4WD chassis systems.
  • BD3.1: an eddy-current brake power interface. Its electrical supply and brake compatibility must be checked for the installation.

The DC2 specification distinguishes the two variants and identifies the DC2 as a development of the earlier DC1E4. Dyno2 software supplies test display, recording and analysis; exact operating modes depend on the complete configured system.

Checking a retrofit

Record brake model, torque and speed limits, controller, software, power supply, sensor scaling, calibration and interlock arrangements. A capable controller cannot make an absorber motor a shaft or operate safely beyond its own cooling and mechanical limits. See dynamometer control systems.

Details are based on the linked company documentation checked 17 November 2026; verify present configurations and support with the supplier.

Revision 5: PEREK dynamometer controllers

PEREK supplies dynamometer data acquisition, controllers and brake interfaces for new builds and retrofits. Its systems can be configured for engine, rolling-road and hub installations; the controller and power electronics must be matched to the existing dynamometer hardware. See Dynamometers and the manufacturers directory.

PEREK DC2 dynamometer controller and connection terminals.
PEREK DC2 controller. Image: PEREK DC2 product page, used with permission.

History and role

Ronald Perek states that he founded PEREK in 2019 after mechatronics and electronics work at ECUMASTER. The company describes its work as dyno measurement and control, including upgrades of existing equipment from other makers. A conversion can retain the original frame and brake while changing controller components; the dyno's name does not necessarily identify the controller fitted today. PEREK: company and applications.

Systems and applications

PEREK describes its controller system for inertial and braked engine, chassis, hub and power-take-off dynos. Its peripheral guide specifies different speed-sensor counts for different layouts and identifies the separate absorber, load cell and brake supply needed for an absorption dyno. PEREK lists partner builders for complete machines; these are distinct companies, not PEREK dyno model names.

Controller and brake-interface models

  • DC1E4: an earlier controller identified by PEREK in documented retrofit examples, including a Bosch FLA206 upgrade.
  • DC2: an integrated computer and controller; the maker lists support for unsynchronised 4WD chassis and 4WD hub systems with appropriate peripherals.
  • DC2L: a lower-specification DC2-series variant for less complex applications, including mechanically synchronised 4WD chassis systems.
  • BD3.1: an eddy-current brake power interface. Its electrical supply and brake compatibility must be checked for the installation.

The DC2 specification distinguishes the two variants and identifies the DC2 as a development of the earlier DC1E4. Dyno2 software supplies test display, recording and analysis; exact operating modes depend on the complete configured system.

Checking a retrofit

Record brake model, torque and speed limits, controller, software, power supply, sensor scaling, calibration and interlock arrangements. A capable controller cannot make an absorber motor a shaft or operate safely beyond its own cooling and mechanical limits. See dynamometer control systems.

DC2 and DC2L: hardware and applications

Both DC2-series controllers combine a computer and real-time acquisition/control hardware in one enclosure; a separate external PC is not required for normal local operation, although a screen and input devices are needed. PEREK identifies DC2 as an upgrade of the earlier DC1E4. Its full specification distinguishes the versions:

FeatureDC2LDC2
ConfigurationInertia or braked engine, motorcycle and 2WD chassis dynos; mechanically synchronised 4WD chassis dyno.Also supports unsynchronised 4WD chassis and two- or four-wheel hub dynos, with up to four absorber units as configured.
Load-cell inputsOne direct input with built-in amplifier.Four direct inputs with built-in amplifiers.
Frequency inputsOne frequency input plus one multi-sensor engine-speed input.Five frequency inputs plus one multi-sensor engine-speed input.
Analogue channelsOne fast 0–5 V input and four high-precision single-ended inputs, the latter also usable as two differential channels.Twelve fast 0–5 V inputs and eight high-precision single-ended inputs, the latter also usable as four differential channels.
Outputs and CANOne analogue output, two low-side PWM outputs, one relay and one CAN bus.Four analogue outputs, four low-side and four high-side PWM outputs, four relays and two CAN buses.

Input count is not the same as the number of complete dyno channels in every installation: a brake channel also requires a suitable speed pickup, load cell, appropriate power stage, wiring and configuration. The peripherals guide lists one speed sensor for a typical 2WD chassis or mechanically synchronised 4WD setup, two for an unsynchronised 4WD chassis or 2WD hub dyno, and four for a 4WD hub dyno.

Brake power and sensor interfaces

The controller sends a low-power demand signal; an eddy-current brake needs a correctly rated external power stage to supply its coil. PEREK's retrofit guide describes compatible PWM and configurable analogue commands and says an existing compatible power stage may be reusable. It identifies BD2 and BD3 interface families, and the manufacturer describes BD3.1 as a CAN-controlled eddy-brake supply with fast demagnetisation. Verify brake-coil voltage, current, supply and control compatibility rather than assuming any old unit will work.

The same retrofit guide distinguishes DC1-series load-cell signal amplification, which can use a suitable existing amplifier or an LCA1, from DC2's built-in programmable load-cell amplifiers. It describes Hall/toothed-wheel and encoder options; a variable-reluctance sensor may need the specified adapter when used on a general frequency input. Reuse depends on the sensor, signal and power specifications. A wideband oxygen probe normally needs its own compatible lambda controller before its signal is read by the dyno.

Dyno2 software and control

Dyno2 supports live plots, configurable sensor scaling, run comparisons, calibration tools, CSV export, CAN data and programmable auxiliary outputs. The manufacturer describes constant-power, RPM-lock, RPM-limit and sequence modes; the system overview additionally lists steady speed, ramp, programmable acceleration and road simulation. Available functions depend on the controller, firmware, peripherals and physical dyno. Correction factors use measured or entered ambient conditions; a calculated engine-power estimate remains distinct from directly measured hub or wheel output.

Example: Dynocom AWD retrofit

PEREK documents a Dynocom DYNO X AWD conversion using a DC1E4, two BD3 eddy-brake supplies, two replacement load cells with LCA1 amplifiers, and speed wheels and pickups. The account also describes load-cell and inertia calibration, PID setup, and fan and wheelbase control. This illustrates a particular installed conversion, not a guarantee that another Dynocom will have the same brake, wiring or reuse options.

Details are based on the linked company documentation checked 17 November 2026; verify present configurations and support with the supplier.

Additional output and sensor compatibility

Outputs can control compatible external power electronics or actuators using suitable PWM, 0–10 V or CAN commands; PEREK also specifies direct PWM up to 3 A where applicable. A high-current eddy-current absorber generally needs a matched brake power supply. The sensor requirement rises with independently rotating shafts: the peripheral guide lists two speed sensors for a 2WD hub setup and four for a 4WD hub setup. Electronic synchronisation has limits and must suit the vehicle and dyno.

BD3 and BD3.1 eddy-brake power supplies

The BD3/BD3.1 manual describes a separate mains-supplied eddy-current interface with closed-loop brake-current control, fast demagnetisation and CAN diagnostics such as current and power-stage temperature. PEREK lists single- or three-phase supply possibilities and different current ratings and duty limits; match the exact variant, supply, cooling and absorber coil rating. The brake and its power stage, not the DC controller alone, set the available loading.

BD3.1 differs from BD3 in its cooling and power-supply arrangement and removes the earlier PWM input; do not assume both variants accept the same control signals. The manual describes CAN control for BD3.1. Observe the manufacturer's isolation, capacitor-discharge, installation and emergency procedures.

Dyno2 control, logging and automation

Dyno2 supports calibration tools, graphs and run comparison, channels from compatible CAN and OBD equipment, configurable reports and CSV export. PEREK lists modes including RPM lock, constant power, RPM limit and test sequences; availability and usable control depend on the installed hardware and configuration. The run-tab guide also describes manual absorber demand and speed and acceleration control.

In a documented control architecture, the speed loop compares measured and desired speed; a torque loop can then use load-cell feedback to request brake output. A separate position loop can use analogue feedback for a water valve or throttle actuator. PEREK states that these real-time control loops run at 1,000 Hz, whereas an optional software function PID runs at 100 Hz; these are loop update rates, not a guarantee of complete machine response or accuracy. See control-loop documentation.

The manufacturer describes configurable CAN channels, remote-control inputs and test sequences. These features require correct signal, actuator and safety configuration. Dyno2 remote control; retrofitting guidance.

Related comparison: Compare factory and aftermarket dynamometer controllers.