Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Dynamometer refurbishment restores or modernises the test equipment itself: its chassis, rollers or absorber, measurement system and controls. The work can range from a specific repair or calibration to a stripped, rebuilt and recommissioned machine. The following UK-based specialists publish evidence of dynamometer work, but do not all offer the same scope. Confirm current availability, geographic coverage, supported makes and the work included before commissioning a project. Part of the Dynamometers section.

Advanced Dyno Solutions

Advanced Dyno Solutions (ADS) is a specialist in chassis and hub dynamometers. It advertises dyno manufacture, repair, bespoke design, roller knurling, dynamic balancing and test-cell planning, as well as new, used and refurbished equipment. Its upgrades and accessories include Dastek controller upgrades and SportDevices accessories. The exact scope for an individual machine needs a quotation and inspection.

Red chassis and covers from a Dastek dynamometer refurbishment displayed in a workshop.
Chassis parts from a Dastek dyno refurbishment described by ADS in 2016. Photo: Advanced Dyno Solutions, used with permission.

In that documented Dastek example, ADS described surface treatment and repainting, replacement bearings and fasteners, and new control and data-acquisition electronics, wiring, sensors and computer. It is a historical example of a particular overhaul, not a promise that every refurbishment includes those parts. ADS also lists controller upgrades separately, so a controller retrofit should not be assumed to include a full mechanical rebuild.

Other UK services

SupplierPublished evidence of dyno workScope to confirm
Dynamometer World, WorcesterAdvertises major repairs and overhauls of eddy-current and hydraulic dynamometers, reconditioned equipment, parts and balancing. Its site names several engine and chassis dynamometer makes, including Froude, Schenck, Borghi & Saveri and Horiba.Ask whether the particular absorber, model and controller can be overhauled, what parts are included and whether removal and installation are offered.
Hatton SystemsAdvertises chassis dyno calibration, maintenance, repair and mechanical, electrical and control upgrades, including work on other manufacturers' equipment. It describes flywheel-to-electrical inertia simulation as an available conversion.Listed as a repair, calibration and upgrade service; agree whether the required job extends to a complete mechanical rebuild. Confirm the applicable calibration scope and certification.
Apexis Engineering, DerbyDescribes bespoke rolling-road engineering and case studies involving reverse engineering to support dyno retrofitting, relocation, refurbishment or modification.This is published engineering and design experience; confirm whether Apexis would undertake the physical overhaul, work with an installer, or provide engineering support for the specific project.

These are selected examples, not a complete directory or a ranking. Descriptions are based on the suppliers' own published information checked on 17 November 2026; check current service area, lead time and whether the company will accept the equipment directly.

What refurbishment can involve

A repair addresses a known fault, such as a failed sensor, damaged bearing or brake-control problem. A controller retrofit replaces or adapts data acquisition, sensors and load-control hardware while retaining suitable mechanical equipment. A full overhaul may involve dismantling, inspection, dimensional checks, replacement of worn parts, reassembly and testing. These terms are not a universal fixed specification: agree the actual scope rather than relying on a label.

Depending on the equipment and condition, a project can include roller and shaft inspection, bearings and seals, checking or balancing rotating parts, absorber electrical or fluid-system checks, guard and restraint inspection, surface treatment, rewiring, speed sensing and load-cell work. Where a new controller is fitted, confirm the brake interface, sensor scaling, inertia and loss configuration, emergency-stop behaviour and available test modes. Cosmetic refinishing alone does not demonstrate mechanical condition or measurement accuracy.

Questions to ask before ordering

  • Identify the machine: manufacturer, model, serial number, 2WD or 4WD arrangement, absorber type, current controller, fault symptoms and any available drawings or calibration records.
  • Define the work: who removes, transports, installs and commissions it; what is inspected, repaired, replaced or reused; and how additional defects are approved and priced.
  • Check capability: required axle load, roller speed, torque, continuous and peak power, braking duty, cooling and electrical supply. Confirm vehicle compatibility and whether the brake and controller can hold the intended test points.
  • Request evidence: inspection and parts list, balancing where relevant, torque and speed verification, calibration method and traceability, commissioning test results, operating instructions and warranty terms. A traceable instrument does not by itself establish that the supplier or the entire calibration is accredited; ask for the certificate and its scope if accreditation is required.
  • Plan operation: guarding, restraints, emergency stops, ventilation, exhaust extraction, operator training, software licences, spares and support. Agree a repeatable acceptance test appropriate to the machine and its intended use.

See Dynamometer control systems, measurement and interpreting results and test setup and safety for the underlying principles.