Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Dynamometer testing combines rotating machinery, a restrained vehicle or engine, heat, noise and exhaust gases. A test setup must suit the particular dynamometer, vehicle and test cell; the machine manufacturer’s instructions, a competent operator and the site risk assessment take precedence over a generic checklist. See the dynamometers overview and measurement and interpreting results.

Conceptual rolling-road test area showing a restrained vehicle, rollers, cooling airflow, exhaust extraction, exclusion zone and operator controls.
Conceptual rolling-road setup showing the main safety provisions. Actual layout and restraints must follow the vehicle and equipment manufacturers' instructions. Diagram: original illustration created for Tuning Wiki.

Before the vehicle is run

  1. Check compatibility and capacity. Confirm vehicle mass, driven axles, wheelbase, tyre speed rating, power, torque and expected speed are within the dyno, restraint and test-cell limits. An AWD vehicle may require linked rollers or a specific test procedure. Verify the manufacturer’s instructions for the vehicle’s transmission, differential, stability and hybrid systems; do not assume a two-wheel-drive test is safe.
  2. Inspect the machine and vehicle. Check guards, emergency stop, brake, extraction and cooling, and look for leaks, loose parts, damaged tyres and unsafe mechanical condition. Check fluid levels, tyre condition and pressure; remove debris from tread. Arrange leads and hoses away from heat and moving parts. The Dynojet Model 224 installation and operation guide gives a model-specific pre-run inspection.
  3. Position and restrain. Align driven wheels as directed, use rated restraints and designated anchorage points in the arrangement specified for the machine and vehicle, and check tension. Protect straps from abrasion and hot or rotating parts. Chock only where the specific manufacturer’s instructions call for it. Hub and engine installations need correctly rated, properly fitted adapters, fasteners, couplings and supports rather than tyre straps alone.
  4. Prepare the room. Connect suitable exhaust extraction before starting and discharge it to a safe outdoor position; provide adequate replacement air and separate cooling airflow. HSE warns that exhaust fumes can rapidly reach harmful concentrations and that open doors alone are not a reliable control. See HSE vehicle exhaust emissions and HSE SR14 guidance. A cooling fan aimed at the radiator or intercooler is not a substitute for exhaust extraction.

People and operating area

Limit access, communicate the test and stop procedure, and position people outside the machine’s danger zones. The Dynojet Model 224 guide says only the operator should be near the vehicle during operation and nobody should stand behind it. Keep hands, clothing, cables and tools clear of rollers, tyres, shafts, couplings and fan blades. Fit guards and use appropriate hearing and eye protection. Verify the emergency stop and operator’s safe access before the run. The site’s risk assessment should cover fire, fuel, hot surfaces, ejected objects, noise, electrical hazards and the stored energy in a spinning roller. Dynojet Model 224 guide; Dynojet safety warnings.

During and after a test

Begin with a controlled low-load check for alignment, movement, vibration, smoke, leaks, abnormal noise and believable speed signals. Stop the test if anything is abnormal, if restraint or extraction fails, or if operating limits are approached. Keep cooling and extraction effective through the test and cooldown. Do not approach or adjust moving parts while they coast down; wait until rotation has stopped and isolate equipment as required before servicing or removing guards. Follow the manufacturer’s shutdown and unloading sequence.

Engine and hub installations

An engine cell needs suitable mounts, a guarded coupling, services for fuel, cooling and exhaust, and controls for both the engine and absorber. Torque reactions and vibration must be carried by the designed supports. Hub dynos remove tyre slip but still require secure adapters, correct fasteners and restraint, with the vehicle supported according to the equipment maker’s procedure. Neither layout removes the need for an exclusion zone, emergency shutdown, extraction or cooling.

Recording a repeatable setup

Once safe, record the dyno and vehicle configuration, restraint and tyre setup, fuel, test gear, test mode, sweep rate, cooling and temperatures, and the correction method. Use consistent warm-up and cooldown, and investigate wheel slip or changes in boost, temperature or electronic intervention before attributing a curve change to a modification. Manufacturer-specific procedures and the site’s safety arrangements determine the details. See SuperFlow: dynamometer testing oversights.