Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Ford

Ford's 2013 model-year Fiesta DPS6 OBD system summary describes a six-speed dual-clutch transmission with manual-type gearing and electric actuators. It has two dry clutches and two gear paths; it is not the five-speed single-clutch Durashift EST described in the earlier Fiesta guide. Other transmissions sold as PowerShift can differ. Confirm the model, market, transmission code, controller and calibration before applying a test. Ford 2013 Fiesta OBD-II system operation summary, pp. 103–106.

Architecture and speed signals

In Ford's 2013 example, clutch A and input shaft 1 serve first, third and fifth; clutch B and input shaft 2 serve reverse, second, fourth and sixth. Two shift drums select the gear paths. The controller operates individual electric clutch and shift motors and uses motor position feedback. This two-path arrangement is different from a twin-plate single clutch and from a torque-converter automatic.

Ford describes input-speed sensors for each shaft and an output-speed sensor. Compare the applicable clutch/gear request and input speeds with the output speed, using the diagnostic tool's definitions, to investigate a shift or ratio complaint. A channel showing an unexpected speed can reflect signal, wiring, control or mechanical issues; it does not alone prove clutch slip. Source: Ford 2013 summary, pp. 103–105.

Ford calls this example a dry-clutch transmission, but its gearset still uses oil for splash lubrication. Its summary states that this DPS6 has no hydraulic pump, pressure-control solenoids or transmission-fluid temperature sensor; that description must not be transferred to other PowerShift variants or years.

Documented diagnostic examples

2013 Fiesta DPS6 monitorExample from FordInterpretation
Input 1 speedP0715 circuit, P0716 erratic, P0717 missingCheck the complete sensor and circuit test and related data; a speed code is not proof of a damaged gear.
Input 2 speedP2765 circuit, P2766 erratic, P2767 missingKeep the second gear path and its sensor distinct from input 1. Check the actual fault definition and conditions.
Clutch A actuatorP0900 open, P0902 short to ground, P0903 short to powerThese are Ford's electrical-monitor descriptions for this system; assess supply, wiring, control and actuator with its test plan.
Clutch B actuatorP090A open, P090C short to ground, P090D short to powerDo not treat an A-side code as a B-side diagnosis or infer a failed clutch assembly from a circuit label.

Source: Ford 2013 Fiesta OBD summary, pp. 105–106. These codes are scoped to the documented calibration and do not replace the current VIN-specific service test. Record any suffix, fault status and freeze-frame information, if provided.

Shudder and service information

Ford's historical TSB 16-0109 addresses excessive clutch shudder under light acceleration and possible fluid leakage on specified 2011–2015 Fiesta and 2012–2016 Focus vehicles with DPS6, subject to its detailed build criteria. It directs diagnosis by symptom and saving diagnostic data; a leak may or may not be present. It warns that service routines clear adaptive strategy and incomplete routines may cause erratic shifts. The bulletin is historical and Ford's current bulletin listing marks it superseded or deactivated; check the VIN and latest Ford service instructions rather than using it as an automatic repair or warranty entitlement.

A practical sequence

  1. Record the complaint, temperature and load, first or reverse engagement, whether it affects one gear path, warning, prior repairs and fluid history. Save transmission and engine codes and their operating conditions before clearing.
  2. Check battery and module supply, grounds and communications as directed by the exact vehicle's test plan. Compare the two input speeds, output speed, selected gear and relevant clutch/shift commands where available.
  3. Use Ford's symptom and electrical tests for the specific failure. Check for the documented form of shudder or fluid contamination when relevant; neither a shudder nor an actuator code proves that a particular part needs replacement.
  4. After a confirmed repair, use the current Ford instructions and approved equipment for any programming and learning functions. These routines have prerequisites and can move components. Do not clear adaptive values as a substitute for correcting a mechanical or electrical fault.

See automated clutch and shift control, dual-clutch flywheels and Ford Durashift EST.