Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Smart

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Daimler's training for the smart fortwo model series 451 describes a five-speed automated manual gearbox with a single-plate dry clutch operated by an electric clutch motor. A control unit coordinates the clutch and two electric shift actuators. This layout is not the same as the electrohydraulic Mercedes 716.6 SEQUENTRONIC, even though a Daimler bulletin calls the 451 system an automated manual / Sequentronic ASG. Confirm the exact vehicle, market, powertrain and service data; do not apply the example to every smart or electric-drive model. Daimler: Introduction of the smart fortwo 451, transmission control and clutch.

What the controller operates

The 451 training describes a transmission controller that checks the driver's shift request against signals including vehicle speed, engine speed and load. When conditions permit, it commands the clutch motor and the motors operating the two selector drums. The clutch motor moves an actuating plunger to release the clutch, so a single friction clutch remains present even though there is no clutch pedal. The exact functions and modes are application-specific. Daimler 451 training, printed pp. 57 and 63.

A documented no-shift case

Daimler XENTRY document LI26.60-P-055839, version 2, 5 March 2013 concerns a defined model-451 VIN range. It describes an occasional inability to engage a gear, with one or more warnings, three bars in the cluster, or P2802 and P0707 plus additional fault codes. In that documented case the reported cause is contact resistance at the shift-actuator connector. This does not establish that every three-bar warning, P2802 or P0707 is caused by that connector.

The bulletin directs inspection of the two shift-actuator motor connectors, their latches, wiring and cable covering, followed by its specific corrective and teach-in steps. It explicitly says not to use contact spray or grease in the connectors for that repair. Check the bulletin's VIN applicability and current repair data; inspect the circuit and diagnose the actual fault rather than replacing the shift or clutch motor from the display alone.

Transmission communication fault from an accessoryDaimler XENTRY LI54.30-P-054004, version 2 describes a model 451.3/4 case with a continuously illuminated engine warning and U0002 in the ME7_451 engine controller and/or U0122 in the TCU_451 transmission controller. Daimler identifies electrical feedback from certain battery-powered accessories as a possible cause, including equipment powered through the 12 V socket or connected directly to circuit 15. Check the actual vehicle and accessory history and follow the current diagnostic plan: the fault code is not proof of a failed transmission controller.The bulletin’s diode retrofit applies only to accessories operated through the 12 V socket; Daimler explicitly excludes accessories wired directly to circuit 15 from that particular remedy. Do not generalise this fix to every CAN communication fault, fit a diode without the prescribed procedure, or assume a particular vehicle has the described condition.

Diagnosis and repair boundaries

Save transmission and other relevant control-unit faults and their status before clearing anything. Record voltage, conditions, selector request, displayed and actual gear, brake input and when the concern occurs. Use the correct tool and test plan to compare requested gear, gear-position feedback, clutch actuation, transmission speed and motor command as supported by that vehicle. Check supply, grounds, connector integrity and wiring under appropriate conditions; the display is a symptom rather than a component verdict. Assess the mechanical clutch, release linkage and selector mechanism when evidence points there. The supplier SACHS clutch-actuator service note covers specified 451/454 and other applications and warns that the actuator can exert high force; follow the specific installation and handling instructions. After the repair, perform the manufacturer-required clutch and transmission teach-in only with the correct procedure and prerequisites, then confirm the complaint. Daimler includes teach-in in the specific connector bulletin; it is not proof that adaptation fixes every fault.

See Mercedes 716.6 Sequentronic and automated manual clutch and gearshift control.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Smart fortwo 451 automated manual clutch and shift diagnosis

Daimler's training for the smart fortwo model series 451 describes a five-speed automated manual gearbox with a single-plate dry clutch operated by an electric clutch motor. A control unit coordinates the clutch and two electric shift actuators. This layout is not the same as the electrohydraulic Mercedes 716.6 SEQUENTRONIC, even though a Daimler bulletin calls the 451 system an automated manual / Sequentronic ASG. Confirm the exact vehicle, market, powertrain and service data; do not apply the example to every smart or electric-drive model. Daimler: Introduction of the smart fortwo 451, transmission control and clutch.

What the controller operates

The 451 training describes a transmission controller that checks the driver's shift request against signals including vehicle speed, engine speed and load. When conditions permit, it commands the clutch motor and the motors operating the two selector drums. The clutch motor moves an actuating plunger to release the clutch, so a single friction clutch remains present even though there is no clutch pedal. The exact functions and modes are application-specific. Daimler 451 training, printed pp. 57 and 63.

A documented no-shift case

Daimler XENTRY document LI26.60-P-055839, version 2, 5 March 2013 concerns a defined model-451 VIN range. It describes an occasional inability to engage a gear, with one or more warnings, three bars in the cluster, or P2802 and P0707 plus additional fault codes. In that documented case the reported cause is contact resistance at the shift-actuator connector. This does not establish that every three-bar warning, P2802 or P0707 is caused by that connector.

The bulletin directs inspection of the two shift-actuator motor connectors, their latches, wiring and cable covering, followed by its specific corrective and teach-in steps. It explicitly says not to use contact spray or grease in the connectors for that repair. Check the bulletin's VIN applicability and current repair data; inspect the circuit and diagnose the actual fault rather than replacing the shift or clutch motor from the display alone.

Diagnosis and repair boundaries

  1. Save transmission and other relevant control-unit faults and their status before clearing anything. Record voltage, conditions, selector request, displayed and actual gear, brake input and when the concern occurs.
  2. Use the correct tool and test plan to compare requested gear, gear-position feedback, clutch actuation, transmission speed and motor command as supported by that vehicle. Check supply, grounds, connector integrity and wiring under appropriate conditions; the display is a symptom rather than a component verdict.
  3. Assess the mechanical clutch, release linkage and selector mechanism when evidence points there. The supplier SACHS clutch-actuator service note covers specified 451/454 and other applications and warns that the actuator can exert high force; follow the specific installation and handling instructions.
  4. After the repair, perform the manufacturer-required clutch and transmission teach-in only with the correct procedure and prerequisites, then confirm the complaint. Daimler includes teach-in in the specific connector bulletin; it is not proof that adaptation fixes every fault.

See Mercedes 716.6 Sequentronic and automated manual clutch and gearshift control.

Revision 2: Smart fortwo 451 automated manual clutch and shift diagnosis

Daimler's training for the smart fortwo model series 451 describes a five-speed automated manual gearbox with a single-plate dry clutch operated by an electric clutch motor. A control unit coordinates the clutch and two electric shift actuators. This layout is not the same as the electrohydraulic Mercedes 716.6 SEQUENTRONIC, even though a Daimler bulletin calls the 451 system an automated manual / Sequentronic ASG. Confirm the exact vehicle, market, powertrain and service data; do not apply the example to every smart or electric-drive model. Daimler: Introduction of the smart fortwo 451, transmission control and clutch.

What the controller operates

The 451 training describes a transmission controller that checks the driver's shift request against signals including vehicle speed, engine speed and load. When conditions permit, it commands the clutch motor and the motors operating the two selector drums. The clutch motor moves an actuating plunger to release the clutch, so a single friction clutch remains present even though there is no clutch pedal. The exact functions and modes are application-specific. Daimler 451 training, printed pp. 57 and 63.

A documented no-shift case

Daimler XENTRY document LI26.60-P-055839, version 2, 5 March 2013 concerns a defined model-451 VIN range. It describes an occasional inability to engage a gear, with one or more warnings, three bars in the cluster, or P2802 and P0707 plus additional fault codes. In that documented case the reported cause is contact resistance at the shift-actuator connector. This does not establish that every three-bar warning, P2802 or P0707 is caused by that connector.

The bulletin directs inspection of the two shift-actuator motor connectors, their latches, wiring and cable covering, followed by its specific corrective and teach-in steps. It explicitly says not to use contact spray or grease in the connectors for that repair. Check the bulletin's VIN applicability and current repair data; inspect the circuit and diagnose the actual fault rather than replacing the shift or clutch motor from the display alone.

Transmission communication fault from an accessory

Daimler XENTRY LI54.30-P-054004, version 2 describes a model 451.3/4 case with a continuously illuminated engine warning and U0002 in the ME7_451 engine controller and/or U0122 in the TCU_451 transmission controller. Daimler identifies electrical feedback from certain battery-powered accessories as a possible cause, including equipment powered through the 12 V socket or connected directly to circuit 15. Check the actual vehicle and accessory history and follow the current diagnostic plan: the fault code is not proof of a failed transmission controller.

The bulletin’s diode retrofit applies only to accessories operated through the 12 V socket; Daimler explicitly excludes accessories wired directly to circuit 15 from that particular remedy. Do not generalise this fix to every CAN communication fault, fit a diode without the prescribed procedure, or assume a particular vehicle has the described condition.

Diagnosis and repair boundaries

  1. Save transmission and other relevant control-unit faults and their status before clearing anything. Record voltage, conditions, selector request, displayed and actual gear, brake input and when the concern occurs.
  2. Use the correct tool and test plan to compare requested gear, gear-position feedback, clutch actuation, transmission speed and motor command as supported by that vehicle. Check supply, grounds, connector integrity and wiring under appropriate conditions; the display is a symptom rather than a component verdict.
  3. Assess the mechanical clutch, release linkage and selector mechanism when evidence points there. The supplier SACHS clutch-actuator service note covers specified 451/454 and other applications and warns that the actuator can exert high force; follow the specific installation and handling instructions.
  4. After the repair, perform the manufacturer-required clutch and transmission teach-in only with the correct procedure and prerequisites, then confirm the complaint. Daimler includes teach-in in the specific connector bulletin; it is not proof that adaptation fixes every fault.

See Mercedes 716.6 Sequentronic and automated manual clutch and gearshift control.