Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Speeduino standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
The original Dropbear V1 is an eight-injector, eight-ignition-output Speeduino ECU based on Teensy 3.5. The project guide describes its logic pre-drivers, two 24-way connectors, internal VR conditioning and CAN. Outputs and software assignments depend on configuration.
Black 24-way connector
From the project Dropbear connector guide. Consult its connector face view, fusing, electrical ratings and switches.
PinFunctionA1Switched 12 VA2Power groundA35 V sensor referenceA4Not usedA5Spare digital input 2A6CAN LA7CAN HA8Power groundB1TachometerB2Crank primaryB3Crank negative (VR only)B4Cam primaryB5Cam negative (VR only)B6Spare digital input 1B7Clutch input (ground switching)B8Flex sensorC1Analog sensor groundC2Spare analog input 1C3Spare analog input 2C4Oxygen sensor inputC5Coolant sensorC6Intake air sensorC7Throttle positionC8External MAP input
Grey 24-way connector
PinFunctionA1Injector 1A2Injector 2A3Injector 3A4Injector 4A5Injector 5A6Injector 6A7Injector 7A8Injector 8B1Ignition 1B2Ignition 2B3Ignition 3B4Ignition 4B5Ignition 5B6Ignition 6B7Ignition 7B8Ignition 8C1BoostC2Fan relayC3Spare 2 / stepper B2C4Idle / stepper B1C5VVT / stepper A1C6Spare 1 / idle 2 / stepper A2C7Fuel pump relayC8Power ground
Generation-specific software pin numbers
The harness terminal names above are the same in the project guide. TunerStudio pin identifiers differ between generations, so select the actual hardware. Source: Speeduino Dropbear documentation.
Black terminalFunctionV1 software pinV2 software pinA5Spare digital 22234B6Spare digital 12335C2Spare analogue 1A17A16C3Spare analogue 2A18A17
See the Dropbear family page and Speeduino index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Speeduino Dropbear V1
The original Dropbear V1 is an eight-injector, eight-ignition-output Speeduino ECU based on Teensy 3.5. The project guide describes its logic pre-drivers, two 24-way connectors, internal VR conditioning and CAN. Outputs and software assignments depend on configuration.
Black 24-way connector
From the project Dropbear connector guide. Consult its connector face view, fusing, electrical ratings and switches.
| Pin | Function |
|---|
| A1 | Switched 12 V |
| A2 | Power ground |
| A3 | 5 V sensor reference |
| A4 | Not used |
| A5 | Spare digital input 2 |
| A6 | CAN L |
| A7 | CAN H |
| A8 | Power ground |
| B1 | Tachometer |
| B2 | Crank primary |
| B3 | Crank negative (VR only) |
| B4 | Cam primary |
| B5 | Cam negative (VR only) |
| B6 | Spare digital input 1 |
| B7 | Clutch input (ground switching) |
| B8 | Flex sensor |
| C1 | Analog sensor ground |
| C2 | Spare analog input 1 |
| C3 | Spare analog input 2 |
| C4 | Oxygen sensor input |
| C5 | Coolant sensor |
| C6 | Intake air sensor |
| C7 | Throttle position |
| C8 | External MAP input |
Grey 24-way connector
| Pin | Function |
|---|
| A1 | Injector 1 |
| A2 | Injector 2 |
| A3 | Injector 3 |
| A4 | Injector 4 |
| A5 | Injector 5 |
| A6 | Injector 6 |
| A7 | Injector 7 |
| A8 | Injector 8 |
| B1 | Ignition 1 |
| B2 | Ignition 2 |
| B3 | Ignition 3 |
| B4 | Ignition 4 |
| B5 | Ignition 5 |
| B6 | Ignition 6 |
| B7 | Ignition 7 |
| B8 | Ignition 8 |
| C1 | Boost |
| C2 | Fan relay |
| C3 | Spare 2 / stepper B2 |
| C4 | Idle / stepper B1 |
| C5 | VVT / stepper A1 |
| C6 | Spare 1 / idle 2 / stepper A2 |
| C7 | Fuel pump relay |
| C8 | Power ground |
Generation-specific software pin numbers
The harness terminal names above are the same in the project guide. TunerStudio pin identifiers differ between generations, so select the actual hardware. Source: Speeduino Dropbear documentation.
| Black terminal | Function | V1 software pin | V2 software pin |
|---|
| A5 | Spare digital 2 | 22 | 34 |
| B6 | Spare digital 1 | 23 | 35 |
| C2 | Spare analogue 1 | A17 | A16 |
| C3 | Spare analogue 2 | A18 | A17 |
See the Dropbear family page and Speeduino index.
Revision 1: Speeduino Dropbear V1
The original Dropbear V1 is an eight-injector, eight-ignition-output Speeduino ECU based on Teensy 3.5. The project guide describes its logic pre-drivers, two 24-way connectors, internal VR conditioning and CAN. Outputs and software assignments depend on configuration.
Black 24-way connector
From the project Dropbear connector guide. Consult its connector face view, fusing, electrical ratings and switches.
| Pin | Function |
|---|
| A1 | Switched 12 V |
| A2 | Power ground |
| A3 | 5 V sensor reference |
| A4 | Not used |
| A5 | Spare digital input 2 |
| A6 | CAN L |
| A7 | CAN H |
| A8 | Power ground |
| B1 | Tachometer |
| B2 | Crank primary |
| B3 | Crank negative (VR only) |
| B4 | Cam primary |
| B5 | Cam negative (VR only) |
| B6 | Spare digital input 1 |
| B7 | Clutch input (ground switching) |
| B8 | Flex sensor |
| C1 | Analog sensor ground |
| C2 | Spare analog input 1 |
| C3 | Spare analog input 2 |
| C4 | Oxygen sensor input |
| C5 | Coolant sensor |
| C6 | Intake air sensor |
| C7 | Throttle position |
| C8 | External MAP input |
Grey 24-way connector
| Pin | Function |
|---|
| A1 | Injector 1 |
| A2 | Injector 2 |
| A3 | Injector 3 |
| A4 | Injector 4 |
| A5 | Injector 5 |
| A6 | Injector 6 |
| A7 | Injector 7 |
| A8 | Injector 8 |
| B1 | Ignition 1 |
| B2 | Ignition 2 |
| B3 | Ignition 3 |
| B4 | Ignition 4 |
| B5 | Ignition 5 |
| B6 | Ignition 6 |
| B7 | Ignition 7 |
| B8 | Ignition 8 |
| C1 | Boost |
| C2 | Fan relay |
| C3 | Spare 2 / stepper B2 |
| C4 | Idle / stepper B1 |
| C5 | VVT / stepper A1 |
| C6 | Spare 1 / idle 2 / stepper A2 |
| C7 | Fuel pump relay |
| C8 | Power ground |
Generation-specific software pin numbers
The harness terminal names above are the same in the project guide. TunerStudio pin identifiers differ between generations, so select the actual hardware. Source: Speeduino Dropbear documentation.
| Black terminal | Function | V1 software pin | V2 software pin |
|---|
| A5 | Spare digital 2 | 22 | 34 |
| B6 | Spare digital 1 | 23 | 35 |
| C2 | Spare analogue 1 | A17 | A16 |
| C3 | Spare analogue 2 | A18 | A17 |
See the Dropbear family page and Speeduino index.