Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Clutches
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

A clutch connects and disconnects rotating parts so that an engine can keep running while the vehicle stops, move the vehicle away smoothly and allow gears to change. This guide concentrates on friction clutches between an engine and transmission. Clutches also perform different jobs inside automatic transmissions and torque converters; identify the complete system before applying a diagnosis or buying parts.

Typical manual layouts: the clutch sits between the flywheel and gearbox. Components vary by application. Original diagram prepared for Tuning Wiki, CC BY 4.0.

How a friction clutch works

In a common dry manual clutch, the flywheel is attached to the crankshaft. A driven disc, splined to the gearbox input shaft, is clamped against the flywheel by the pressure plate and its spring. With sufficient clamp force and friction, the components turn together and transmit torque. When the release mechanism acts on the spring, clamp force falls and the disc can separate, interrupting drive.

During take-up the disc and flywheel turn at different speeds. Controlled slip allows a smooth start but converts energy to heat; extended slip under load can overheat the friction surfaces. The amount of torque a clutch can hold depends on the whole design, including clamp force, friction material, effective radius, number of friction surfaces, temperature and condition. See ZF: causes of clutch slip and flywheel construction.

Clutch layouts

TypeHow it is usedThings to consider Single-plate dry friction clutchA common manual-car layout uses one driven disc between flywheel and pressure plate.Disc, cover, flywheel, release mechanism and any torsional damping must be matched. Multi-plate clutchTwo or more driven discs provide additional friction interfaces in a package; designs may be dry or oil-cooled.More plates can increase torque capacity for a given overall diameter, but noise, release behaviour, heat capacity and packaging depend on the design. Wet clutchFriction plates operate with the manufacturer's specified oil, often in motorcycles, dual-clutch or automatic transmissions.Oil specification, cooling, condition and the control system matter; it is not interchangeable with a dry-clutch kit. Dual clutchTwo independently controlled clutches connect different gear paths in a dual-clutch transmission.Wet and dry arrangements exist; it is distinct from a single-clutch automated manual even when both have paddles.

These are different ways of describing the hardware: a twin-plate clutch is not automatically a dual-clutch transmission, and wet/dry describes the friction environment rather than how many gear paths exist. Schaeffler: wet and dry double-clutch systems; EXEDY: single- and multi-plate examples.

Manual and automated control

In a conventional manual car the driver operates the clutch pedal. A cable or hydraulic system moves the release mechanism; in a hydraulic design a master cylinder supplies a slave cylinder, which may operate a fork or be concentric with the gearbox input shaft. Pedal down normally releases the clutch; pedal up lets the pressure spring clamp it. The driver controls clutch engagement while selecting gears. ZF: hydraulic actuation.

An automated manual transmission retains a friction clutch and a geared transmission but uses actuators, governed by a control unit, to operate the clutch and select gears. It may offer automatic and driver-requested shifts, sometimes with steering-wheel paddles. The controller coordinates clutch movement and engine torque, but the exact strategy, hydraulic or electric actuator and diagnostics vary. A paddle shift does not by itself identify an automated manual, a dual-clutch or a torque-converter automatic. See automated manual clutch and gearshift control and F1-style automated manual gearbox examples.

Friction materials, damping and modifications

Road and performance clutches may use organic, cerametallic, sintered or carbon-based friction materials; the name alone does not define a particular operating temperature, pedal effort, torque rating or street suitability. A sprung disc hub can provide torsional damping; rigid hubs remove that feature, and the complete flywheel and driveline damping arrangement must be considered. Disc cushioning and pressure-plate design also affect engagement.

As a product-specific example, EXEDY describes its Stage 1 organic kit as having similar drivability to its original-equipment comparison and higher pedal effort, while its Stage 2 cerametallic kit engages more aggressively. Other products can behave differently: material labels or “stage” numbers are not universal ratings. EXEDY also offers both damped and rigid multi-plate designs. EXEDY: multi-plate example.

Choose by measured or anticipated engine torque, duty cycle, vehicle mass, grip and intended use; check the manufacturer's torque rating and conditions, flywheel and input spline, pressure-plate dimensions, release travel and service instructions. A higher clamp load can increase pedal force in a particular system and may increase stresses elsewhere. A clutch upgrade does not itself add engine power. See performance flywheel choices and fitment and balancing.

Symptoms and service

Slip: engine speed rises without a corresponding increase in road speed under load. Worn or contaminated linings, incorrect release adjustment, a faulty pressure plate or unsuitable parts are among possible causes; a new disc alone does not rule out a release-system fault. Drag or incomplete release: difficult gear engagement or a tendency to creep with the clutch commanded open can involve the release system, hydraulic air or leaks, a sticking input spline or pilot bearing, disc distortion or installation errors. Judder or noise: record whether the condition occurs during take-up, with the pedal up or down, hot or cold, and under load. Clutch, flywheel, bearings, mounts and uneven engine running can all be relevant; no single noise proves which part has failed.

Consult the exact vehicle's service procedure for inspection, adjustment, bleeding and any electronic clutch calibration or adaptation. Do not assume a generic bleed sequence, clutch wear value or adaptation reset applies across makes. For mechanical evidence see ZF: slipping, ZF: incomplete release and flywheel faults and noise.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Clutches

A clutch connects and disconnects rotating parts so that an engine can keep running while the vehicle stops, move the vehicle away smoothly and allow gears to change. This guide concentrates on friction clutches between an engine and transmission. Clutches also perform different jobs inside automatic transmissions and torque converters; identify the complete system before applying a diagnosis or buying parts.

Representative manual clutch layouts with single-mass and dual-mass flywheels
Typical manual layouts: the clutch sits between the flywheel and gearbox. Components vary by application. Original diagram prepared for Tuning Wiki, CC BY 4.0.

How a friction clutch works

In a common dry manual clutch, the flywheel is attached to the crankshaft. A driven disc, splined to the gearbox input shaft, is clamped against the flywheel by the pressure plate and its spring. With sufficient clamp force and friction, the components turn together and transmit torque. When the release mechanism acts on the spring, clamp force falls and the disc can separate, interrupting drive.

During take-up the disc and flywheel turn at different speeds. Controlled slip allows a smooth start but converts energy to heat; extended slip under load can overheat the friction surfaces. The amount of torque a clutch can hold depends on the whole design, including clamp force, friction material, effective radius, number of friction surfaces, temperature and condition. See ZF: causes of clutch slip and flywheel construction.

Clutch layouts

TypeHow it is usedThings to consider
Single-plate dry friction clutchA common manual-car layout uses one driven disc between flywheel and pressure plate.Disc, cover, flywheel, release mechanism and any torsional damping must be matched.
Multi-plate clutchTwo or more driven discs provide additional friction interfaces in a package; designs may be dry or oil-cooled.More plates can increase torque capacity for a given overall diameter, but noise, release behaviour, heat capacity and packaging depend on the design.
Wet clutchFriction plates operate with the manufacturer's specified oil, often in motorcycles, dual-clutch or automatic transmissions.Oil specification, cooling, condition and the control system matter; it is not interchangeable with a dry-clutch kit.
Dual clutchTwo independently controlled clutches connect different gear paths in a dual-clutch transmission.Wet and dry arrangements exist; it is distinct from a single-clutch automated manual even when both have paddles.

These are different ways of describing the hardware: a twin-plate clutch is not automatically a dual-clutch transmission, and wet/dry describes the friction environment rather than how many gear paths exist. Schaeffler: wet and dry double-clutch systems; EXEDY: single- and multi-plate examples.

Manual and automated control

In a conventional manual car the driver operates the clutch pedal. A cable or hydraulic system moves the release mechanism; in a hydraulic design a master cylinder supplies a slave cylinder, which may operate a fork or be concentric with the gearbox input shaft. Pedal down normally releases the clutch; pedal up lets the pressure spring clamp it. The driver controls clutch engagement while selecting gears. ZF: hydraulic actuation.

An automated manual transmission retains a friction clutch and a geared transmission but uses actuators, governed by a control unit, to operate the clutch and select gears. It may offer automatic and driver-requested shifts, sometimes with steering-wheel paddles. The controller coordinates clutch movement and engine torque, but the exact strategy, hydraulic or electric actuator and diagnostics vary. A paddle shift does not by itself identify an automated manual, a dual-clutch or a torque-converter automatic. See automated manual clutch and gearshift control and F1-style automated manual gearbox examples.

Friction materials, damping and modifications

Road and performance clutches may use organic, cerametallic, sintered or carbon-based friction materials; the name alone does not define a particular operating temperature, pedal effort, torque rating or street suitability. A sprung disc hub can provide torsional damping; rigid hubs remove that feature, and the complete flywheel and driveline damping arrangement must be considered. Disc cushioning and pressure-plate design also affect engagement.

As a product-specific example, EXEDY describes its Stage 1 organic kit as having similar drivability to its original-equipment comparison and higher pedal effort, while its Stage 2 cerametallic kit engages more aggressively. Other products can behave differently: material labels or “stage” numbers are not universal ratings. EXEDY also offers both damped and rigid multi-plate designs. EXEDY: multi-plate example.

Choose by measured or anticipated engine torque, duty cycle, vehicle mass, grip and intended use; check the manufacturer's torque rating and conditions, flywheel and input spline, pressure-plate dimensions, release travel and service instructions. A higher clamp load can increase pedal force in a particular system and may increase stresses elsewhere. A clutch upgrade does not itself add engine power. See performance flywheel choices and fitment and balancing.

Symptoms and service

  • Slip: engine speed rises without a corresponding increase in road speed under load. Worn or contaminated linings, incorrect release adjustment, a faulty pressure plate or unsuitable parts are among possible causes; a new disc alone does not rule out a release-system fault.
  • Drag or incomplete release: difficult gear engagement or a tendency to creep with the clutch commanded open can involve the release system, hydraulic air or leaks, a sticking input spline or pilot bearing, disc distortion or installation errors.
  • Judder or noise: record whether the condition occurs during take-up, with the pedal up or down, hot or cold, and under load. Clutch, flywheel, bearings, mounts and uneven engine running can all be relevant; no single noise proves which part has failed.

Consult the exact vehicle's service procedure for inspection, adjustment, bleeding and any electronic clutch calibration or adaptation. Do not assume a generic bleed sequence, clutch wear value or adaptation reset applies across makes. For mechanical evidence see ZF: slipping, ZF: incomplete release and flywheel faults and noise.

Revision 1: Clutches

A clutch connects and disconnects rotating parts so that an engine can keep running while the vehicle stops, move the vehicle away smoothly and allow gears to change. This guide concentrates on friction clutches between an engine and transmission. Clutches also perform different jobs inside automatic transmissions and torque converters; identify the complete system before applying a diagnosis or buying parts.

Representative manual clutch layouts with single-mass and dual-mass flywheels
Typical manual layouts: the clutch sits between the flywheel and gearbox. Components vary by application. Original diagram prepared for Tuning Wiki, CC BY 4.0.

How a friction clutch works

In a common dry manual clutch, the flywheel is attached to the crankshaft. A driven disc, splined to the gearbox input shaft, is clamped against the flywheel by the pressure plate and its spring. With sufficient clamp force and friction, the components turn together and transmit torque. When the release mechanism acts on the spring, clamp force falls and the disc can separate, interrupting drive.

During take-up the disc and flywheel turn at different speeds. Controlled slip allows a smooth start but converts energy to heat; extended slip under load can overheat the friction surfaces. The amount of torque a clutch can hold depends on the whole design, including clamp force, friction material, effective radius, number of friction surfaces, temperature and condition. See ZF: causes of clutch slip and flywheel construction.

Clutch layouts

TypeHow it is usedThings to consider
Single-plate dry friction clutchA common manual-car layout uses one driven disc between flywheel and pressure plate.Disc, cover, flywheel, release mechanism and any torsional damping must be matched.
Multi-plate clutchTwo or more driven discs provide additional friction interfaces in a package; designs may be dry or oil-cooled.More plates can increase torque capacity for a given overall diameter, but noise, release behaviour, heat capacity and packaging depend on the design.
Wet clutchFriction plates operate with the manufacturer's specified oil, often in motorcycles, dual-clutch or automatic transmissions.Oil specification, cooling, condition and the control system matter; it is not interchangeable with a dry-clutch kit.
Dual clutchTwo independently controlled clutches connect different gear paths in a dual-clutch transmission.Wet and dry arrangements exist; it is distinct from a single-clutch automated manual even when both have paddles.

These are different ways of describing the hardware: a twin-plate clutch is not automatically a dual-clutch transmission, and wet/dry describes the friction environment rather than how many gear paths exist. Schaeffler: wet and dry double-clutch systems; EXEDY: single- and multi-plate examples.

Manual and automated control

In a conventional manual car the driver operates the clutch pedal. A cable or hydraulic system moves the release mechanism; in a hydraulic design a master cylinder supplies a slave cylinder, which may operate a fork or be concentric with the gearbox input shaft. Pedal down normally releases the clutch; pedal up lets the pressure spring clamp it. The driver controls clutch engagement while selecting gears. ZF: hydraulic actuation.

An automated manual transmission retains a friction clutch and a geared transmission but uses actuators, governed by a control unit, to operate the clutch and select gears. It may offer automatic and driver-requested shifts, sometimes with steering-wheel paddles. The controller coordinates clutch movement and engine torque, but the exact strategy, hydraulic or electric actuator and diagnostics vary. A paddle shift does not by itself identify an automated manual, a dual-clutch or a torque-converter automatic. See automated manual clutch and gearshift control and F1-style automated manual gearbox examples.

Friction materials, damping and modifications

Road and performance clutches may use organic, cerametallic, sintered or carbon-based friction materials; the name alone does not define a particular operating temperature, pedal effort, torque rating or street suitability. A sprung disc hub can provide torsional damping; rigid hubs remove that feature, and the complete flywheel and driveline damping arrangement must be considered. Disc cushioning and pressure-plate design also affect engagement.

As a product-specific example, EXEDY describes its Stage 1 organic kit as having similar drivability to its original-equipment comparison and higher pedal effort, while its Stage 2 cerametallic kit engages more aggressively. Other products can behave differently: material labels or “stage” numbers are not universal ratings. EXEDY also offers both damped and rigid multi-plate designs. EXEDY: multi-plate example.

Choose by measured or anticipated engine torque, duty cycle, vehicle mass, grip and intended use; check the manufacturer's torque rating and conditions, flywheel and input spline, pressure-plate dimensions, release travel and service instructions. A higher clamp load can increase pedal force in a particular system and may increase stresses elsewhere. A clutch upgrade does not itself add engine power. See performance flywheel choices and fitment and balancing.

Symptoms and service

  • Slip: engine speed rises without a corresponding increase in road speed under load. Worn or contaminated linings, incorrect release adjustment, a faulty pressure plate or unsuitable parts are among possible causes; a new disc alone does not rule out a release-system fault.
  • Drag or incomplete release: difficult gear engagement or a tendency to creep with the clutch commanded open can involve the release system, hydraulic air or leaks, a sticking input spline or pilot bearing, disc distortion or installation errors.
  • Judder or noise: record whether the condition occurs during take-up, with the pedal up or down, hot or cold, and under load. Clutch, flywheel, bearings, mounts and uneven engine running can all be relevant; no single noise proves which part has failed.

Consult the exact vehicle's service procedure for inspection, adjustment, bleeding and any electronic clutch calibration or adaptation. Do not assume a generic bleed sequence, clutch wear value or adaptation reset applies across makes. For mechanical evidence see ZF: slipping, ZF: incomplete release and flywheel faults and noise.