Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Speeduino standalone ECUs
Applies to
Speeduino standalone ECUs
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

v0.4 board layout. Image: Speeduino project, reproduced with permission.

The v0.4 project board uses four injector channels, four ignition outputs, a 40-pin IDC I/O connector and a separate 12 V feed. It includes provision for an optional DRV8825 stepper idle driver, MAP sensor and VR conditioner. It was developed for a different integration approach from the screw-terminal v0.3.

40-pin IDC connections

Project v0.4 manual: confirm connector orientation, PCB revision, populated options and any modification. The 12 V supply is separate. Prototype pins 14–18 have the documented default assignments only from v0.4.4b onward and require matching configuration.

PinFunction1Injector 1 (1/2)2Injector 2 (1/2)3Injector 3 (1/2)4Injector 3 (2/2)5Injector 4 (1/2)6Injector 4 (2/2)7Ignition 18Ignition 49Ground10Ground11MAP 0–5 V12Ground135 V14Proto 1 (0.4.4b+ flex)15Proto 2 (0.4.4b+ fan)16Proto 3 (0.4.4b+ fuel pump)17Proto 4 (0.4.4b+ tachometer)18Proto 5 (0.4.4b+ clutch)19Coolant20Intake air temperature21Oxygen sensor22Throttle position23Ground24Cam / VR2+25Crank / VR1+26VR2−27VR1−285 V29Stepper 2B30Stepper 2A31Stepper 1A32Stepper 1B33Ignition 334Ignition 235Boost36Idle 237PWM idle38VVT39Injector 2 (2/2)40Injector 1 (2/2)

On versions 0.4.3c and earlier, component orientation differs from 0.4.3d and later; follow the exact revision’s assembly notes. Official revision files.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Speeduino v0.4

The v0.4 project board uses four injector channels, four ignition outputs, a 40-pin IDC I/O connector and a separate 12 V feed. It includes provision for an optional DRV8825 stepper idle driver, MAP sensor and VR conditioner. It was developed for a different integration approach from the screw-terminal v0.3.

40-pin IDC connections

Project v0.4 manual: confirm connector orientation, PCB revision, populated options and any modification. The 12 V supply is separate. Prototype pins 14–18 have the documented default assignments only from v0.4.4b onward and require matching configuration.

PinFunction
1Injector 1 (1/2)
2Injector 2 (1/2)
3Injector 3 (1/2)
4Injector 3 (2/2)
5Injector 4 (1/2)
6Injector 4 (2/2)
7Ignition 1
8Ignition 4
9Ground
10Ground
11MAP 0–5 V
12Ground
135 V
14Proto 1 (0.4.4b+ flex)
15Proto 2 (0.4.4b+ fan)
16Proto 3 (0.4.4b+ fuel pump)
17Proto 4 (0.4.4b+ tachometer)
18Proto 5 (0.4.4b+ clutch)
19Coolant
20Intake air temperature
21Oxygen sensor
22Throttle position
23Ground
24Cam / VR2+
25Crank / VR1+
26VR2−
27VR1−
285 V
29Stepper 2B
30Stepper 2A
31Stepper 1A
32Stepper 1B
33Ignition 3
34Ignition 2
35Boost
36Idle 2
37PWM idle
38VVT
39Injector 2 (2/2)
40Injector 1 (2/2)

On versions 0.4.3c and earlier, component orientation differs from 0.4.3d and later; follow the exact revision’s assembly notes. Official revision files.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.

Revision 2: Speeduino v0.4
Speeduino v0.4 board layout
v0.4 board layout. Image: Speeduino project, reproduced with permission.

The v0.4 project board uses four injector channels, four ignition outputs, a 40-pin IDC I/O connector and a separate 12 V feed. It includes provision for an optional DRV8825 stepper idle driver, MAP sensor and VR conditioner. It was developed for a different integration approach from the screw-terminal v0.3.

40-pin IDC connections

Project v0.4 manual: confirm connector orientation, PCB revision, populated options and any modification. The 12 V supply is separate. Prototype pins 14–18 have the documented default assignments only from v0.4.4b onward and require matching configuration.

PinFunction
1Injector 1 (1/2)
2Injector 2 (1/2)
3Injector 3 (1/2)
4Injector 3 (2/2)
5Injector 4 (1/2)
6Injector 4 (2/2)
7Ignition 1
8Ignition 4
9Ground
10Ground
11MAP 0–5 V
12Ground
135 V
14Proto 1 (0.4.4b+ flex)
15Proto 2 (0.4.4b+ fan)
16Proto 3 (0.4.4b+ fuel pump)
17Proto 4 (0.4.4b+ tachometer)
18Proto 5 (0.4.4b+ clutch)
19Coolant
20Intake air temperature
21Oxygen sensor
22Throttle position
23Ground
24Cam / VR2+
25Crank / VR1+
26VR2−
27VR1−
285 V
29Stepper 2B
30Stepper 2A
31Stepper 1A
32Stepper 1B
33Ignition 3
34Ignition 2
35Boost
36Idle 2
37PWM idle
38VVT
39Injector 2 (2/2)
40Injector 1 (2/2)

On versions 0.4.3c and earlier, component orientation differs from 0.4.3d and later; follow the exact revision’s assembly notes. Official revision files.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.