Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch Motronic 7
Applies to
Bosch ME7.1, Bosch ME7.5
Tool groups
None
Manufacturers
Audi, Volkswagen

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

Scope and the air path

These diagnostic examples concern turbocharged VAG ME7.1/ME7.5 engines with a mass-air meter. Confirm the particular engine's ducting, pressure-sensor locations and valve arrangement: other ME7 installations differ. A loss of response, low measured airflow or a pressure-control fault can be caused by a leak, a restriction, a sensor or control problem, or more than one fault. Record fault codes and freeze-frame data before clearing anything.

Follow the physical path from air filter and MAF to compressor inlet, compressor outlet, intercooler, throttle and intake manifold, including the recirculating diverter-valve and ventilation branches. A leak after the MAF or a restriction upstream of the compressor does not have the same operating conditions as a split in a pressurised charge pipe. Its effect varies with engine load, actual pressure and flow direction. See MAF and lambda log review and diverter valves.

A hose can collapse only under flow

In a forum-reported modified Golf 4 GTI 1.8T/ME7.5 case, throttle intervention was initially described and calibration changes were tried. After it was suggested that the silicone turbo inlet might collapse, the inlet was reported to have collapsed and the problem resolved. The available discussion does not establish every intermediate sensor signal or prove that other cars with similar plots have the same fault.In a separate Audi A3 AUM 1.8T case, a torn turbo-inlet pipe was found. A temporary seal changed the reported MAF reading, and the initial limp-mode complaint was later reported to disappear after replacing both the inlet and MAF. That joint replacement does not isolate which part caused every symptom, and later posts still discuss other concerns. The symptom was initially associated with B_lambts; a concurrent enrichment status alone did not establish its cause.In a modified Golf 4 GTI 1.8T/ME7.5 NefMoto case, the owner initially described throttle intervention and tried calibration changes. After another participant suggested the silicone turbo inlet might collapse, the owner reported that it had collapsed and that the problem was resolved. The available discussion does not establish every intermediate sensor signal or prove that other cars with similar plots have the same fault.In a separate Audi A3 AUM 1.8T case, the owner found a torn turbo-inlet pipe. A temporary seal changed the reported MAF reading; the owner later reported that the initial limp-mode complaint disappeared after replacing both the inlet and MAF. That joint replacement does not isolate which part caused every symptom, and later posts still discuss other concerns. The owner initially associated the symptom with B_lambts; a concurrent enrichment status alone did not establish its cause.

Inspect condition and fit as well as logs. A pipe can look normal at rest, and a positive-pressure leak test does not reproduce the suction and airflow that may deform an inlet. If necessary, measure compressor-inlet pressure with suitable equipment at a correctly identified location under controlled, appropriate operating conditions; compare with the component maker's specifications. Do not use the charge-pressure sensor downstream of the compressor as though it were an inlet-vacuum gauge. Keep hands and equipment clear of moving and hot parts.

Garrett's compressor-mapping explanation illustrates why a filter or inlet-duct pressure drop lowers compressor inlet absolute pressure. At a given compressor-outlet absolute pressure this increases compressor pressure ratio; a boost gauge by itself does not measure the inlet depression.

Worked compressor pressure-ratio check

Garrett's compressor-map guide uses compressor outlet absolute pressure divided by compressor inlet absolute pressure. Manifold pressure alone omits both charge-path pressure drop and inlet depression. For illustration, suppose ambient pressure is 1000 mbar absolute, compressor-inlet pressure is 950 mbar absolute, manifold pressure is 2000 mbar absolute, and compressor-to-manifold loss is 100 mbar. Compressor outlet pressure is 2100 mbar absolute, so the compressor ratio is 2100 ÷ 950 ≈ 2.21. Using manifold pressure ÷ ambient would give 2.00 and miss both losses. These are invented values for explaining the calculation, not operating targets.

Measure pressures at identified locations under comparable conditions, with appropriately rated equipment. The actual compressor map may use corrected rather than uncorrected mass flow; check the map's units and correction convention before plotting a log. Compare a range of operating points, including low-flow spool and higher-flow operation, rather than one peak-pressure reading. BorgWarner's map explanation describes corrected flow, pressure ratio, efficiency islands, surge, choke and shaft-speed lines. A calculated operating point or noise alone does not prove surge or shaft speed; use the correct map and, where needed, direct speed measurement.

Same gauge boost at different ambient pressuresAltitude or weather changes the ambient pressure on which a gauge is referenced. Keeping the previous illustration's 50 mbar inlet depression and 100 mbar compressor-to-manifold pressure loss, consider the same 1000 mbar gauge manifold pressure at two ambient pressures. At 1000 mbar ambient, the compressor inlet and outlet are 950 and 2100 mbar absolute, giving a ratio of about 2.21. At 800 mbar ambient, the manifold is 1800 mbar absolute, the compressor inlet is 750 mbar, and the outlet is 1900 mbar: the ratio rises to about 2.53. These assumed pressures illustrate the calculation, not a safe target or a prediction of the actual losses. Garrett's compressor map guide explains the effects of both elevation and inlet depression on pressure ratio.Do not equate that measured hardware ratio with an ECU map value without tracing the model. The translated Audi 132 kW 1.8T ME7.1 function description, LDRLMX, describes KFLDHBN as a compressor pressure-ratio limit used with external pressure and converted to a cylinder-charge limit. It also refers to surge, turbo speed and poor-efficiency regions when establishing the limit. That documented calculation does not establish that the ECU directly measures compressor inlet and outlet pressures. Identify the software's model, pressure locations and compressor map; a higher limit chosen simply to obtain more boost can remove an intended constraint. See ME7 torque, load and boost control for the competing request limits.

Know what the pressure test actually covers

Identify the isolated test volume, pressure reference, connected branches and valve actuation state before interpreting the result. A test of a section can establish that section's external leakage at the test condition; it cannot establish the condition of an excluded hose, a valve under a different pressure difference, or an inlet that deforms under suction. Use the vehicle or component manufacturer's test method and pressure limits.

A forum-reported 1.8T AWW case recognised that pressurising the intake from the MAF connection could pressurise both sides of the recirculation path, masking an internal diverter-valve leak. A split coupler was later reported found and replaced: the car improved, but the original part-throttle issue remained, and a separate valve test reportedly passed. This is a lesson about test boundaries and multiple faults, not proof that the valve in that car failed.In a 1.8T AWW discussion, the owner recognised that pressurising the intake from the MAF connection could pressurise both sides of the recirculation path, masking an internal diverter-valve leak. Later, the owner reported finding and replacing a split coupler: the car improved, but the original part-throttle issue remained, and their separate valve test reportedly passed. This is a lesson about test boundaries and multiple faults, not proof that the valve in that car failed.

Compare measurements before changing the tune

Log pedal request and actual throttle angle, RPM, relevant fault and intervention states, MAF signal, boost request and measured charge pressure. Add final lambda request and actual lambda where available. Confirm signal definitions, sampling and sensor range. Compare like with like: on the cited VAG configurations, pvdks_w identifies pressure before the throttle, while ps_w can be a calculated manifold pressure. Throttle position and pressure losses can make them differ. Use an independently measured manifold pressure where required; do not treat either as compressor-inlet pressure. In a forum-reported modified BFB 1.8T case, changing model-related calibration improved agreement between reported pressure traces, yet drivability symptoms were still reported and the cause remained disputed. Agreement alone does not prove that the model is correct, that a leak is absent, or that compressor surge occurred.Log pedal request and actual throttle angle, RPM, relevant fault and intervention states, MAF signal, boost request and measured charge pressure. Add final lambda request and actual lambda where available. Confirm signal definitions, sampling and sensor range. Compare like with like: on the cited VAG configurations, pvdks_w identifies pressure before the throttle, while ps_w can be a calculated manifold pressure. Throttle position and pressure losses can make them differ. Use an independently measured manifold pressure where required; do not treat either as compressor-inlet pressure. In a modified BFB 1.8T case, changing model-related calibration improved agreement between reported pressure traces, yet the owner still reported drivability symptoms. Participants disputed the cause. Agreement alone does not prove that the model is correct, that a leak is absent, or that compressor surge occurred.

Motorservice notes that intake leaks, a blocked filter and other faults can contribute to a misleading air-mass signal; an air-mass fault code does not by itself prove the sensor is defective. See its air-mass sensor diagnostic guide. Continue with boost and load log review and pressure-sensor validation. Forum outcomes above are owner reports and have not been independently reproduced by this wiki.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: ME7 turbo inlet restriction and charge-air leak diagnosis

Scope and the air path

These diagnostic examples concern turbocharged VAG ME7.1/ME7.5 engines with a mass-air meter. Confirm the particular engine's ducting, pressure-sensor locations and valve arrangement: other ME7 installations differ. A loss of response, low measured airflow or a pressure-control fault can be caused by a leak, a restriction, a sensor or control problem, or more than one fault. Record fault codes and freeze-frame data before clearing anything.

Follow the physical path from air filter and MAF to compressor inlet, compressor outlet, intercooler, throttle and intake manifold, including the recirculating diverter-valve and ventilation branches. A leak after the MAF or a restriction upstream of the compressor does not have the same operating conditions as a split in a pressurised charge pipe. Its effect varies with engine load, actual pressure and flow direction. See MAF and lambda log review and diverter valves.

A hose can collapse only under flow

In a modified Golf 4 GTI 1.8T/ME7.5 NefMoto case, the owner initially described throttle intervention and tried calibration changes. After another participant suggested the silicone turbo inlet might collapse, the owner reported that it had collapsed and that the problem was resolved. The available discussion does not establish every intermediate sensor signal or prove that other cars with similar plots have the same fault.

In a separate Audi A3 AUM 1.8T case, the owner found a torn turbo-inlet pipe. A temporary seal changed the reported MAF reading; the owner later reported that the initial limp-mode complaint disappeared after replacing both the inlet and MAF. That joint replacement does not isolate which part caused every symptom, and later posts still discuss other concerns. The owner initially associated the symptom with B_lambts; a concurrent enrichment status alone did not establish its cause.

Inspect condition and fit as well as logs. A pipe can look normal at rest, and a positive-pressure leak test does not reproduce the suction and airflow that may deform an inlet. If necessary, measure compressor-inlet pressure with suitable equipment at a correctly identified location under controlled, appropriate operating conditions; compare with the component maker's specifications. Do not use the charge-pressure sensor downstream of the compressor as though it were an inlet-vacuum gauge. Keep hands and equipment clear of moving and hot parts.

Garrett's compressor-mapping explanation illustrates why a filter or inlet-duct pressure drop lowers compressor inlet absolute pressure. At a given compressor-outlet absolute pressure this increases compressor pressure ratio; a boost gauge by itself does not measure the inlet depression.

Worked compressor pressure-ratio check

Garrett's compressor-map guide uses compressor outlet absolute pressure divided by compressor inlet absolute pressure. Manifold pressure alone omits both charge-path pressure drop and inlet depression. For illustration, suppose ambient pressure is 1000 mbar absolute, compressor-inlet pressure is 950 mbar absolute, manifold pressure is 2000 mbar absolute, and compressor-to-manifold loss is 100 mbar. Compressor outlet pressure is 2100 mbar absolute, so the compressor ratio is 2100 ÷ 950 ≈ 2.21. Using manifold pressure ÷ ambient would give 2.00 and miss both losses. These are invented values for explaining the calculation, not operating targets.

Measure pressures at identified locations under comparable conditions, with appropriately rated equipment. The actual compressor map may use corrected rather than uncorrected mass flow; check the map's units and correction convention before plotting a log. Compare a range of operating points, including low-flow spool and higher-flow operation, rather than one peak-pressure reading. BorgWarner's map explanation describes corrected flow, pressure ratio, efficiency islands, surge, choke and shaft-speed lines. A calculated operating point or noise alone does not prove surge or shaft speed; use the correct map and, where needed, direct speed measurement.

Know what the pressure test actually covers

Identify the isolated test volume, pressure reference, connected branches and valve actuation state before interpreting the result. A test of a section can establish that section's external leakage at the test condition; it cannot establish the condition of an excluded hose, a valve under a different pressure difference, or an inlet that deforms under suction. Use the vehicle or component manufacturer's test method and pressure limits.

In a 1.8T AWW discussion, the owner recognised that pressurising the intake from the MAF connection could pressurise both sides of the recirculation path, masking an internal diverter-valve leak. Later, the owner reported finding and replacing a split coupler: the car improved, but the original part-throttle issue remained, and their separate valve test reportedly passed. This is a lesson about test boundaries and multiple faults, not proof that the valve in that car failed.

Compare measurements before changing the tune

  • Log pedal request and actual throttle angle, RPM, relevant fault and intervention states, MAF signal, boost request and measured charge pressure. Add final lambda request and actual lambda where available. Confirm signal definitions, sampling and sensor range.
  • Compare like with like: on the cited VAG configurations, pvdks_w identifies pressure before the throttle, while ps_w can be a calculated manifold pressure. Throttle position and pressure losses can make them differ. Use an independently measured manifold pressure where required; do not treat either as compressor-inlet pressure.
  • In a modified BFB 1.8T case, changing model-related calibration improved agreement between reported pressure traces, yet the owner still reported drivability symptoms. Participants disputed the cause. Agreement alone does not prove that the model is correct, that a leak is absent, or that compressor surge occurred.

Motorservice notes that intake leaks, a blocked filter and other faults can contribute to a misleading air-mass signal; an air-mass fault code does not by itself prove the sensor is defective. See its air-mass sensor diagnostic guide. Continue with boost and load log review and pressure-sensor validation. Forum outcomes above are owner reports and have not been independently reproduced by this wiki.

Revision 4: ME7 turbo inlet restriction and charge-air leak diagnosis

Scope and the air path

These diagnostic examples concern turbocharged VAG ME7.1/ME7.5 engines with a mass-air meter. Confirm the particular engine's ducting, pressure-sensor locations and valve arrangement: other ME7 installations differ. A loss of response, low measured airflow or a pressure-control fault can be caused by a leak, a restriction, a sensor or control problem, or more than one fault. Record fault codes and freeze-frame data before clearing anything.

Follow the physical path from air filter and MAF to compressor inlet, compressor outlet, intercooler, throttle and intake manifold, including the recirculating diverter-valve and ventilation branches. A leak after the MAF or a restriction upstream of the compressor does not have the same operating conditions as a split in a pressurised charge pipe. Its effect varies with engine load, actual pressure and flow direction. See MAF and lambda log review and diverter valves.

A hose can collapse only under flow

In a forum-reported modified Golf 4 GTI 1.8T/ME7.5 case, throttle intervention was initially described and calibration changes were tried. After it was suggested that the silicone turbo inlet might collapse, the inlet was reported to have collapsed and the problem resolved. The available discussion does not establish every intermediate sensor signal or prove that other cars with similar plots have the same fault.

In a separate Audi A3 AUM 1.8T case, a torn turbo-inlet pipe was found. A temporary seal changed the reported MAF reading, and the initial limp-mode complaint was later reported to disappear after replacing both the inlet and MAF. That joint replacement does not isolate which part caused every symptom, and later posts still discuss other concerns. The symptom was initially associated with B_lambts; a concurrent enrichment status alone did not establish its cause.

Inspect condition and fit as well as logs. A pipe can look normal at rest, and a positive-pressure leak test does not reproduce the suction and airflow that may deform an inlet. If necessary, measure compressor-inlet pressure with suitable equipment at a correctly identified location under controlled, appropriate operating conditions; compare with the component maker's specifications. Do not use the charge-pressure sensor downstream of the compressor as though it were an inlet-vacuum gauge. Keep hands and equipment clear of moving and hot parts.

Garrett's compressor-mapping explanation illustrates why a filter or inlet-duct pressure drop lowers compressor inlet absolute pressure. At a given compressor-outlet absolute pressure this increases compressor pressure ratio; a boost gauge by itself does not measure the inlet depression.

Worked compressor pressure-ratio check

Garrett's compressor-map guide uses compressor outlet absolute pressure divided by compressor inlet absolute pressure. Manifold pressure alone omits both charge-path pressure drop and inlet depression. For illustration, suppose ambient pressure is 1000 mbar absolute, compressor-inlet pressure is 950 mbar absolute, manifold pressure is 2000 mbar absolute, and compressor-to-manifold loss is 100 mbar. Compressor outlet pressure is 2100 mbar absolute, so the compressor ratio is 2100 ÷ 950 ≈ 2.21. Using manifold pressure ÷ ambient would give 2.00 and miss both losses. These are invented values for explaining the calculation, not operating targets.

Measure pressures at identified locations under comparable conditions, with appropriately rated equipment. The actual compressor map may use corrected rather than uncorrected mass flow; check the map's units and correction convention before plotting a log. Compare a range of operating points, including low-flow spool and higher-flow operation, rather than one peak-pressure reading. BorgWarner's map explanation describes corrected flow, pressure ratio, efficiency islands, surge, choke and shaft-speed lines. A calculated operating point or noise alone does not prove surge or shaft speed; use the correct map and, where needed, direct speed measurement.

Same gauge boost at different ambient pressures

Altitude or weather changes the ambient pressure on which a gauge is referenced. Keeping the previous illustration's 50 mbar inlet depression and 100 mbar compressor-to-manifold pressure loss, consider the same 1000 mbar gauge manifold pressure at two ambient pressures. At 1000 mbar ambient, the compressor inlet and outlet are 950 and 2100 mbar absolute, giving a ratio of about 2.21. At 800 mbar ambient, the manifold is 1800 mbar absolute, the compressor inlet is 750 mbar, and the outlet is 1900 mbar: the ratio rises to about 2.53. These assumed pressures illustrate the calculation, not a safe target or a prediction of the actual losses. Garrett's compressor map guide explains the effects of both elevation and inlet depression on pressure ratio.

Do not equate that measured hardware ratio with an ECU map value without tracing the model. The translated Audi 132 kW 1.8T ME7.1 function description, LDRLMX, describes KFLDHBN as a compressor pressure-ratio limit used with external pressure and converted to a cylinder-charge limit. It also refers to surge, turbo speed and poor-efficiency regions when establishing the limit. That documented calculation does not establish that the ECU directly measures compressor inlet and outlet pressures. Identify the software's model, pressure locations and compressor map; a higher limit chosen simply to obtain more boost can remove an intended constraint. See ME7 torque, load and boost control for the competing request limits.

Know what the pressure test actually covers

Identify the isolated test volume, pressure reference, connected branches and valve actuation state before interpreting the result. A test of a section can establish that section's external leakage at the test condition; it cannot establish the condition of an excluded hose, a valve under a different pressure difference, or an inlet that deforms under suction. Use the vehicle or component manufacturer's test method and pressure limits.

A forum-reported 1.8T AWW case recognised that pressurising the intake from the MAF connection could pressurise both sides of the recirculation path, masking an internal diverter-valve leak. A split coupler was later reported found and replaced: the car improved, but the original part-throttle issue remained, and a separate valve test reportedly passed. This is a lesson about test boundaries and multiple faults, not proof that the valve in that car failed.

Compare measurements before changing the tune

  • Log pedal request and actual throttle angle, RPM, relevant fault and intervention states, MAF signal, boost request and measured charge pressure. Add final lambda request and actual lambda where available. Confirm signal definitions, sampling and sensor range.
  • Compare like with like: on the cited VAG configurations, pvdks_w identifies pressure before the throttle, while ps_w can be a calculated manifold pressure. Throttle position and pressure losses can make them differ. Use an independently measured manifold pressure where required; do not treat either as compressor-inlet pressure.
  • In a forum-reported modified BFB 1.8T case, changing model-related calibration improved agreement between reported pressure traces, yet drivability symptoms were still reported and the cause remained disputed. Agreement alone does not prove that the model is correct, that a leak is absent, or that compressor surge occurred.

Motorservice notes that intake leaks, a blocked filter and other faults can contribute to a misleading air-mass signal; an air-mass fault code does not by itself prove the sensor is defective. See its air-mass sensor diagnostic guide. Continue with boost and load log review and pressure-sensor validation. Forum outcomes above are owner reports and have not been independently reproduced by this wiki.