Identify the measurement
Use this guide for VAG ME7.1/ME7.5 examples after identifying the ECU, its pressure-sensor location, sensor part number, supply, calibration and logger definition. A sensor before the throttle measures a different location from a sensor in the intake manifold. Determine whether each pressure is absolute or gauge and whether a 5120-style representation or logger correction is already present.
The sensor's transfer describes how its output changes with pressure. Many automotive sensors are ratiometric to their supply, so the output must be interpreted with the specified reference voltage; this is not a promise that all sensors use the same endpoints. Bosch describes ratiometric output in its pressure-sensor technical information.
Relocation is more than a transfer-curve change. Moving a sensor from a charge pipe ahead of the throttle to the manifold changes the physical quantity presented to the ECU, especially when there is a pressure drop across the throttle. A forum relocation discussion established no complete single-table solution and raised throttle-related functions as a concern. Bosch's ME7.3.1H function description is a different application, but illustrates that sensor fitment and pre- versus post-throttle pressures feed multiple model functions. Check the exact VAG software, configuration, diagnostics and all signal consumers; sensor scaling alone does not establish correct control after a relocation.
Illustration of a linear transfer
Suppose a hypothetical sensor at its specified supply gives 0.5 V at 200 mbar absolute and 4.5 V at 3000 mbar absolute. Within that assumed linear range, the slope is (3000 − 200) ÷ (4.5 − 0.5) = 700 mbar/V, and the zero-volt intercept is −150 mbar. Thus the illustrative relationship is pressure = 700 × voltage − 150, with pressure in mbar and voltage in volts. At 1.65 V it gives 1005 mbar absolute.
The negative intercept is a property of the straight-line calculation; it is not a claim that the sensor reports a negative pressure at its valid lower endpoint. These are invented endpoints, not settings or a specification for any real sensor. The ECU may store gradient and offset in different units, scaled integers or a different sign convention. Check the matched function and definition before relating this physical equation to DSLGRAD, DSLOFS or another parameter.
Sensor conversion and diagnostic plausibility are separate checks
In Bentley's MY 2012 Continental 6.0 W12 turbo OBD strategy, section 15.13, the ME7.1.1 boost-pressure sensor monitor includes circuit, range and rationality checks. Its described plausibility bounds include a modelled minimum derived from atmospheric pressure and air-filter pressure loss and a modelled maximum involving engine speed. A value remaining outside a limit for the required time can produce a fault when monitoring conditions are met.
This is a separately documented W12 strategy, not proof of identical maps, thresholds or diagnostic logic in a VAG 1.8T or 2.7T. It illustrates why a changed sensor transfer and a plausible atmospheric reading do not alone establish that the complete diagnostic path remains appropriate. With an approved sensor installation, verify the signal at independently known pressures and review faults, readiness and relevant plausibility conditions in the exact application; an inactive or passed monitor does not by itself prove accuracy over the full range. Do not suppress diagnostics to conceal a pressure mismatch.
Validate more than one point
- With ignition on, engine stopped and the air path equalised, compare the appropriate absolute-pressure reading with a reliable local barometer. Confirm that the barometer and logger use the same units and that a 5120 correction has not been applied twice.
- Where the sensor and equipment permit, compare at a second independently known pressure within the sensor's specified range. A plausible atmospheric point alone cannot establish the slope, full range, dynamic response or fault behavior.
- Check sensor supply and ground, output, connector and reference against the manufacturer's data. Check the ECU input, conversion, signal filtering and logger separately. Investigate clipping or implausible steps before changing model or limit maps.
- After fitting a different sensor, verify the specific ECU's remaining pressure representations, diagnostic limits and affected models. Extending the sensor range does not itself extend every ECU function.
In a forum-reported 3-bar-sensor case, a second known-good sensor agreed with ambient using the same calculated coefficients, so a defective first sensor was inferred; its voltage had not been measured, so this was not a bench-confirmed diagnosis. The case also illustrates why a definition that appears unable to display an offset must be checked for its actual representation; do not copy its numeric constants to another file.
Related: ME7 5120 pressure scaling, high-load representation and boost and load log review.
Not established
The Bentley erWin page cited above could not be retrieved when last checked (17 November 2026), so its content is relied on as previously reported; availability may depend on access.