Removed text is struck through; added text is highlighted.
The diesel control unit
Delphi's common-rail manual of September 2007, document DDGX200, calls the controller a DCU and then gives the three expansions it uses: electronic control unit, diesel control unit, and DCM, diesel control module. The same section says the unit reads sensors, drives actuators such as the fan, the EGR valve and the turbo position, runs the strategy, and talks to other controllers. It can manage the injection system, the engine, and functions of the vehicle.
The generations of that DCU are on Delphi DCM. The CRD name used on Mercedes and Jeep files is on Delphi CRD. Bosch and Siemens diesels of the same period are not these units.
What the 2007 system contains
The hydraulic parts in that manual are the DFP1 and DFP3 high-pressure pumps, an inlet metering valve on the pump, a rail, a rail-pressure sensor, and the DFI 1 injector. Rail-pressure sensors in the manual are specified up to 1,600, 1,800 and 2,000 bar. The DFI 1 injector is a solenoid. The coil opens a valve, the pressure above the needle falls, and the needle lifts. At a rail pressure of 1,600 bar the manual says the loss across the feed orifice to the needle exceeds 100 bar, so the pressure at the needle is below rail pressure. Valve travel is about 30 µm. The opening current is higher than the holding current.
A high-pressure valve on the rail, the HPV, is the later way to dump rail pressure. Where the system has no HPV, a short pulse can lift the injector valve and empty the rail to the return without lifting the needle. That pulse length is taken from the injector's own characteristic. An HPV system does not use that injector discharge. With both valves fitted, the manual allows three modes: HPV only with the inlet valve fully open, inlet valve only with the HPV shut, or both together. Inlet-valve current works backwards from a throttle: if rail pressure is below the demand, the current is reduced so the pump takes in more fuel.
C2I and C3I
C2I is Correction Individuelle Injecteur. The figure 2 stands for the two I letters. The manual's injectors can deliver from 0.5 to 100 mg per stroke at 150 to 1,800 bar. The same pulse on two injectors can differ by as much as 5 mg per stroke. The DCU stores a target, the mean characteristic of a batch. C2I is the correction from that target to the injector in the cylinder. The manufacturing test writes eight coefficients, pilot and main, at 200, 800, 1,200 and 1,600 bar. On the injector they appear as a data-matrix code and as characters.
The 2002 Delphi Diesel Systems manual, DDNX125, describes the aftersales form of that code: 16 hexadecimal characters, nine parameters and a checksum in eight bytes. The controller repeats the checksum. A wrong digit is rejected. That 2002 manual numbers cylinders from the timing-belt end for the system it describes. Do not apply that convention universally: Renault's DCM 1.2 diagnostic manual for program 4D and its listed Vdiag versions identifies cylinder 1 at the flywheel end. Use the engine manufacturer's numbering for the exact application. The code belongs to the cylinder the injector is fitted to. Replacing an injector loads the new code and clears the learned trim of the old one. Replacing the controller means loading the code of every injector, then the vehicle settings. The programming method after that download is the vehicle builder's, and the 2007 manual says it cannot be given as one generic procedure.
C3I, Correction Improved Individual Injector, is the next correction in the 2007 manual. C2I is one straight-line correction and 16 hexadecimal characters. C3I is a three-part straight-line correction and 20 alphanumeric characters. Delphi's later aftermarket note also lists C4I among the names used for an injector code. The 2007 manual stops at C3I. A C2I, a C3I and a Bosch IMA code are not interchangeable. The injector page on this wiki is common-rail diesel injectors.
Torque, in that manual
The 2007 strategy turns the pedal, the speed limiter and cruise into a torque request. Idle, the vehicle systems such as stability control, a limiter inside the DCU, and an additional-torque path then compete. The limiter includes the smoke limit, which reduces fuel from airflow and engine speed and is the path used at altitude, and a reduced-flow mode for a fault that could damage the engine. When the pedal is released, idle takes over at about 1,200 rpm. The final torque is the fuel quantity. That quantity is split into pilot, main and post injections. Post injection is there to heat the exhaust, and on a particle-filter engine the manual gives a regeneration temperature above 650 °C.
An accelerometer on the block resets the pilot. The strategy lengthens a pilot pulse, in steps of a few microseconds, until the pilot combusts. That pulse is the minimum drive pulse. The difference from the C2I value is stored. The manual allows two to six of those stored values per injector, selected by rail pressure. Cylinder balance compares the speed of one firing with the next and trims the main pulse. These are the strategies in DDGX200. A later DCM does not inherit them because it shares the Delphi name.
Sources
Delphi France SAS, Diesel Aftermarket, Common Rail Manual, Principles of Operation, DDGX200(EN), issue 1, September 2007. DCU and DCM, DFP pumps, DFI 1, C2I, C3I, HPV and the torque structure. Mirror: DDGX200. Accessed 2026-11-13.
Delphi Diesel Systems UK, DDNX125(EN), version of 8 January 2002. The 16-character C2I, the checksum, and cylinder numbering from the timing-belt end. DDNX125. Accessed 2026-11-13.
Delphi aftermarket, how to replace common-rail injectors. C2I and C4I listed among the names of an injector code. Delphi how-to. Accessed 2026-11-13.
Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C, page 13B-25: cylinder 1 at the flywheel end. Renault manual (mirror).
Open each version to inspect formatting, tables and photographs.
Revision 3: Delphi diesel
The diesel control unit
Delphi's common-rail manual of September 2007, document DDGX200, calls the controller a DCU and then gives the three expansions it uses: electronic control unit, diesel control unit, and DCM, diesel control module. The same section says the unit reads sensors, drives actuators such as the fan, the EGR valve and the turbo position, runs the strategy, and talks to other controllers. It can manage the injection system, the engine, and functions of the vehicle.
The generations of that DCU are on Delphi DCM. The CRD name used on Mercedes and Jeep files is on Delphi CRD. Bosch and Siemens diesels of the same period are not these units.
What the 2007 system contains
The hydraulic parts in that manual are the DFP1 and DFP3 high-pressure pumps, an inlet metering valve on the pump, a rail, a rail-pressure sensor, and the DFI 1 injector. Rail-pressure sensors in the manual are specified up to 1,600, 1,800 and 2,000 bar. The DFI 1 injector is a solenoid. The coil opens a valve, the pressure above the needle falls, and the needle lifts. At a rail pressure of 1,600 bar the manual says the loss across the feed orifice to the needle exceeds 100 bar, so the pressure at the needle is below rail pressure. Valve travel is about 30 µm. The opening current is higher than the holding current.
A high-pressure valve on the rail, the HPV, is the later way to dump rail pressure. Where the system has no HPV, a short pulse can lift the injector valve and empty the rail to the return without lifting the needle. That pulse length is taken from the injector's own characteristic. An HPV system does not use that injector discharge. With both valves fitted, the manual allows three modes: HPV only with the inlet valve fully open, inlet valve only with the HPV shut, or both together. Inlet-valve current works backwards from a throttle: if rail pressure is below the demand, the current is reduced so the pump takes in more fuel.
C2I and C3I
C2I is Correction Individuelle Injecteur. The figure 2 stands for the two I letters. The manual's injectors can deliver from 0.5 to 100 mg per stroke at 150 to 1,800 bar. The same pulse on two injectors can differ by as much as 5 mg per stroke. The DCU stores a target, the mean characteristic of a batch. C2I is the correction from that target to the injector in the cylinder. The manufacturing test writes eight coefficients, pilot and main, at 200, 800, 1,200 and 1,600 bar. On the injector they appear as a data-matrix code and as characters.
The 2002 Delphi Diesel Systems manual, DDNX125, describes the aftersales form of that code: 16 hexadecimal characters, nine parameters and a checksum in eight bytes. The controller repeats the checksum. A wrong digit is rejected. That 2002 manual numbers cylinders from the timing-belt end for the system it describes. Do not apply that convention universally: Renault's DCM 1.2 diagnostic manual for program 4D and its listed Vdiag versions identifies cylinder 1 at the flywheel end. Use the engine manufacturer's numbering for the exact application. The code belongs to the cylinder the injector is fitted to. Replacing an injector loads the new code and clears the learned trim of the old one. Replacing the controller means loading the code of every injector, then the vehicle settings. The programming method after that download is the vehicle builder's, and the 2007 manual says it cannot be given as one generic procedure.
C3I, Correction Improved Individual Injector, is the next correction in the 2007 manual. C2I is one straight-line correction and 16 hexadecimal characters. C3I is a three-part straight-line correction and 20 alphanumeric characters. Delphi's later aftermarket note also lists C4I among the names used for an injector code. The 2007 manual stops at C3I. A C2I, a C3I and a Bosch IMA code are not interchangeable. The injector page on this wiki is common-rail diesel injectors.
Torque, in that manual
The 2007 strategy turns the pedal, the speed limiter and cruise into a torque request. Idle, the vehicle systems such as stability control, a limiter inside the DCU, and an additional-torque path then compete. The limiter includes the smoke limit, which reduces fuel from airflow and engine speed and is the path used at altitude, and a reduced-flow mode for a fault that could damage the engine. When the pedal is released, idle takes over at about 1,200 rpm. The final torque is the fuel quantity. That quantity is split into pilot, main and post injections. Post injection is there to heat the exhaust, and on a particle-filter engine the manual gives a regeneration temperature above 650 °C.
An accelerometer on the block resets the pilot. The strategy lengthens a pilot pulse, in steps of a few microseconds, until the pilot combusts. That pulse is the minimum drive pulse. The difference from the C2I value is stored. The manual allows two to six of those stored values per injector, selected by rail pressure. Cylinder balance compares the speed of one firing with the next and trims the main pulse. These are the strategies in DDGX200. A later DCM does not inherit them because it shares the Delphi name.
Sources
- Delphi France SAS, Diesel Aftermarket, Common Rail Manual, Principles of Operation, DDGX200(EN), issue 1, September 2007. DCU and DCM, DFP pumps, DFI 1, C2I, C3I, HPV and the torque structure. Mirror: DDGX200. Accessed 2026-11-13.
- Delphi Diesel Systems UK, DDNX125(EN), version of 8 January 2002. The 16-character C2I, the checksum, and cylinder numbering from the timing-belt end. DDNX125. Accessed 2026-11-13.
- Delphi aftermarket, how to replace common-rail injectors. C2I and C4I listed among the names of an injector code. Delphi how-to. Accessed 2026-11-13.
- Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C, page 13B-25: cylinder 1 at the flywheel end. Renault manual (mirror).
Revision 3: Delphi diesel
The diesel control unit
Delphi's common-rail manual of September 2007, document DDGX200, calls the controller a DCU and then gives the three expansions it uses: electronic control unit, diesel control unit, and DCM, diesel control module. The same section says the unit reads sensors, drives actuators such as the fan, the EGR valve and the turbo position, runs the strategy, and talks to other controllers. It can manage the injection system, the engine, and functions of the vehicle.
The generations of that DCU are on Delphi DCM. The CRD name used on Mercedes and Jeep files is on Delphi CRD. Bosch and Siemens diesels of the same period are not these units.
What the 2007 system contains
The hydraulic parts in that manual are the DFP1 and DFP3 high-pressure pumps, an inlet metering valve on the pump, a rail, a rail-pressure sensor, and the DFI 1 injector. Rail-pressure sensors in the manual are specified up to 1,600, 1,800 and 2,000 bar. The DFI 1 injector is a solenoid. The coil opens a valve, the pressure above the needle falls, and the needle lifts. At a rail pressure of 1,600 bar the manual says the loss across the feed orifice to the needle exceeds 100 bar, so the pressure at the needle is below rail pressure. Valve travel is about 30 µm. The opening current is higher than the holding current.
A high-pressure valve on the rail, the HPV, is the later way to dump rail pressure. Where the system has no HPV, a short pulse can lift the injector valve and empty the rail to the return without lifting the needle. That pulse length is taken from the injector's own characteristic. An HPV system does not use that injector discharge. With both valves fitted, the manual allows three modes: HPV only with the inlet valve fully open, inlet valve only with the HPV shut, or both together. Inlet-valve current works backwards from a throttle: if rail pressure is below the demand, the current is reduced so the pump takes in more fuel.
C2I and C3I
C2I is Correction Individuelle Injecteur. The figure 2 stands for the two I letters. The manual's injectors can deliver from 0.5 to 100 mg per stroke at 150 to 1,800 bar. The same pulse on two injectors can differ by as much as 5 mg per stroke. The DCU stores a target, the mean characteristic of a batch. C2I is the correction from that target to the injector in the cylinder. The manufacturing test writes eight coefficients, pilot and main, at 200, 800, 1,200 and 1,600 bar. On the injector they appear as a data-matrix code and as characters.
The 2002 Delphi Diesel Systems manual, DDNX125, describes the aftersales form of that code: 16 hexadecimal characters, nine parameters and a checksum in eight bytes. The controller repeats the checksum. A wrong digit is rejected. That 2002 manual numbers cylinders from the timing-belt end for the system it describes. Do not apply that convention universally: Renault's DCM 1.2 diagnostic manual for program 4D and its listed Vdiag versions identifies cylinder 1 at the flywheel end. Use the engine manufacturer's numbering for the exact application. The code belongs to the cylinder the injector is fitted to. Replacing an injector loads the new code and clears the learned trim of the old one. Replacing the controller means loading the code of every injector, then the vehicle settings. The programming method after that download is the vehicle builder's, and the 2007 manual says it cannot be given as one generic procedure.
C3I, Correction Improved Individual Injector, is the next correction in the 2007 manual. C2I is one straight-line correction and 16 hexadecimal characters. C3I is a three-part straight-line correction and 20 alphanumeric characters. Delphi's later aftermarket note also lists C4I among the names used for an injector code. The 2007 manual stops at C3I. A C2I, a C3I and a Bosch IMA code are not interchangeable. The injector page on this wiki is common-rail diesel injectors.
Torque, in that manual
The 2007 strategy turns the pedal, the speed limiter and cruise into a torque request. Idle, the vehicle systems such as stability control, a limiter inside the DCU, and an additional-torque path then compete. The limiter includes the smoke limit, which reduces fuel from airflow and engine speed and is the path used at altitude, and a reduced-flow mode for a fault that could damage the engine. When the pedal is released, idle takes over at about 1,200 rpm. The final torque is the fuel quantity. That quantity is split into pilot, main and post injections. Post injection is there to heat the exhaust, and on a particle-filter engine the manual gives a regeneration temperature above 650 °C.
An accelerometer on the block resets the pilot. The strategy lengthens a pilot pulse, in steps of a few microseconds, until the pilot combusts. That pulse is the minimum drive pulse. The difference from the C2I value is stored. The manual allows two to six of those stored values per injector, selected by rail pressure. Cylinder balance compares the speed of one firing with the next and trims the main pulse. These are the strategies in DDGX200. A later DCM does not inherit them because it shares the Delphi name.
Sources
- Delphi France SAS, Diesel Aftermarket, Common Rail Manual, Principles of Operation, DDGX200(EN), issue 1, September 2007. DCU and DCM, DFP pumps, DFI 1, C2I, C3I, HPV and the torque structure. Mirror: DDGX200. Accessed 2026-11-13.
- Delphi Diesel Systems UK, DDNX125(EN), version of 8 January 2002. The 16-character C2I, the checksum, and cylinder numbering from the timing-belt end. DDNX125. Accessed 2026-11-13.
- Delphi aftermarket, how to replace common-rail injectors. C2I and C4I listed among the names of an injector code. Delphi how-to. Accessed 2026-11-13.
- Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C, page 13B-25: cylinder 1 at the flywheel end. Renault manual (mirror).