Four-stroke engines · Valves · Burnt valves · Crank and cam sensors
A camshaft is a shaft with one lobe for each valve it opens. The lobe lifts the valve off its seat. The spring shuts it. On a four-stroke the cam turns once for every two turns of the crank, because the valve events belong to one cycle, not to one revolution. How many valves share a cylinder, from two to five, is on valves. This page is where the cam sits and how it reaches them.
The layout is where the cam is
The names are about the cam, even when they sound like names for the valves. An overhead-cam engine and a pushrod engine both have their valves in the head. A sidevalve engine does not.
| Layout | Cam | Valves | What carries the motion |
|---|---|---|---|
| Sidevalve | Low in the block | In the block, beside the bore | A short tappet, sometimes with no pushrod |
| Pushrod, overhead valve | In the block | In the head | Lifter, pushrod and rocker |
| Single overhead cam | One cam in the head, per bank | In the head | A tappet, or a rocker |
| Twin cam | Two cams in the head, per bank | In the head | Usually a bucket tappet on each valve |
Sidevalve
A sidevalve, also called a flathead or an L-head, puts the poppet valves in the block. The camshaft sits low in the block and opens them through tappets and short pushrods, or through tappets alone. The usual arrangement has the valves side by side on one side of the cylinder. A T-head puts the inlet on one side and the exhaust on the other, so the head is a crossflow. The combustion chamber is not a space above the piston. It is a pocket beside the piston, above the valves.
The head can be a simple casting, and the engine is compact. The path in and out of the cylinder is a long way round, the chamber shape limits the compression ratio, and the breathing falls away as speed rises. Sidevalves were ordinary car engines from the late 1890s into the mid-1960s. The Ford Model T, the Ford Model A, the Ford flathead V8, the Morris Eight and the Morris Minor Series I are that layout. A seized sidevalve does not meet the piston, because the valve is beside the bore rather than above it. The same chamber shape is unsuitable for a diesel, which needs a high compression ratio to ignite.
One compromise of the 1950s kept a sidevalve and an overhead valve in the same cylinder. That F-head, or inlet-over-exhaust, was used by Willys, Rover, Land Rover and Rolls-Royce. It is neither a pure sidevalve nor a pushrod head with both valves overhead.
Pushrod
In the usage that stuck, an overhead-valve engine has the valves in the head and the camshaft in the block. A lifter follows the lobe, a pushrod climbs the block, and a rocker pushes the valve down. The head stays small, which is why the layout survived in some American V8s and in diesels that want a short, stiff engine. The train has more reciprocating parts than a cam in the head, so the valves are more willing to float as engine speed rises. The pushrods also occupy space in the head, which is why a pushrod petrol engine rarely has more than two valves per cylinder.
Rare is not the same as impossible. A forked rocker lets one pushrod open two valves. General Motors’ Generation IV small-block used that for a three-valve head. Duramax V8 diesels, the Cummins B series, and the Ford 6.7-litre Power Stroke use four valves per cylinder with the cam still in the block. The Harley-Davidson Milwaukee-Eight, from 2016, is four valves and one cam in the block. Those are on the valves page because the valve count is a separate choice from the cam position.
Two layouts sit between a pushrod engine and an overhead cam. The Ford CVH and the Opel CIH put the camshaft in the head, but below or beside the valves, so a rocker is still required. They are overhead-cam by the location of the shaft and overhead-valve by the way the valve is opened.
One cam in the head
A single overhead camshaft has one camshaft for each bank. A straight engine has one cam. A V or a flat engine has two, one above each bank. The cam opens the valves directly through a tappet, or through a rocker. Most of these heads have two valves per cylinder. Three and four exist: the 1975 Honda Civic’s 1.5-litre engine is a single overhead cam with three valves per cylinder, and the 1973 Triumph Dolomite Sprint is a single overhead cam with four.
Taking the pushrods out lowers the mass that has to be accelerated twice a cam revolution, so the valve gear can be run faster before it floats. The ports no longer have to dodge a row of pushrods. The drive up to the head is the new complication, and the cam timing has to be set again whenever the head comes off.
Two cams in the head
A twin cam, or double overhead cam, has two camshafts over each bank. One opens the inlet valves and the other opens the exhaust valves. A straight engine therefore has two camshafts. A V or a flat engine has four. A V8 advertised as a quad-cam is this layout: four camshafts in the engine, two per bank. Four per bank would be eight camshafts, which is a different and unusual machine.
The usual follower is a bucket tappet on the valve. The two rows of valves can sit at a wider angle than a single cam will comfortably allow, the spark plug can sit between them, and the inlet cam can be moved relative to the crank without moving the exhaust cam. That last point is why variable valve timing on a twin cam is often two mechanisms rather than one. Four valves per cylinder is the usual head. Five was used on some Audi and Volkswagen engines, and on the Yamaha-designed head of the later Toyota 4A-GE. The count, and why five did not replace four, is on the valves page.
How the crank turns the cam
The crank drives the cam at half speed. How the control unit reads that half-speed relationship is on crankshaft and camshaft position sensors. A toothed belt is quiet and does not need oil. It is a scheduled part: if it breaks on an interference engine, a valve can still be open when the piston arrives. A roller chain is noisier and is not usually changed at a fixed distance, though a worn chain and its tensioner still shift the timing. Heavy-truck diesels often use a gear train. Earlier overhead cams, including the Bentley 3 Litre and a long run of aircraft engines, used a shaft and bevel gears in a tower beside the block, so the drive could cope with the head growing as it got hot.
Whatever the drive, the lobe only decides when the valve opens and how far. Too little clearance, a collapsed hydraulic lifter or a worn lobe leaves the valve off its seat, and the face then burns. That failure is on burnt valves.
Sources
Wikipedia text is paraphrased from the cited articles under CC BY-SA 4.0. Accessed 2026-11-13.
- Flathead engine. Valves in the block, the L-head and T-head, the offset chamber, Ford and Morris applications, the unsuitability for diesel, and the 1950s F-head on Willys, Rover, Land Rover and Rolls-Royce.
- Overhead valve engine. Common usage of overhead valve for a cam in the block, pushrods and rockers, valve float from the extra mass, the usual two-valve limit, and the Ford CVH and Opel CIH cams that sit in the head but still below or beside the valves.
- Overhead camshaft engine. One cam per bank and two cams per bank, tappet or rocker against a bucket tappet, the quad-cam name on a V engine, belt and chain drive, and interference damage if a belt fails.
- Multi-valve. Pushrod three-valve and four-valve exceptions, the 1975 Honda Civic 12-valve, and the 1973 Triumph Dolomite Sprint.