Camshafts · Four-stroke engines · Burnt valves
A four-stroke poppet valve is a disc on a stem. The face seals on a seat in the head, or, on a sidevalve, in the block. One valve lets the charge in. One lets the exhaust out. Everything else on this page is a way of arranging those two jobs: beside the bore or above it, and two, three, four or five valves sharing one cylinder. Where the camshaft sits, and how a pushrod or a cam lobe reaches the stem, is on camshafts.
What the valve is doing
The inlet valve is the door for air, and on a port-injected petrol engine for the fuel that was sprayed at the back of it. The exhaust valve is the door for the burnt gas, and it is the one that runs hot. It sheds that heat by sitting on its seat, which conducts into the head and the coolant. A face that does not sit burns through. That fault, and the leak-down test that finds it, is on burnt valves. On a direct-injection petrol engine the inlet valve is not washed by fuel, so it cokes instead of burning. That is carbon deposits, and a leak-down test does not hiss at the tailpipe because the back of an inlet valve is dirty.
More than two valves is there to breathe. Several smaller valves can give more open area than two large ones, each valve is lighter, and the plug can sit in the middle of the chamber. The cost is more parts, more stem seals, and a head that has to find room for the valves and, on a direct-injection engine, for the injector as well.
Side valves
A sidevalve puts both valves in the block, beside the cylinder. The chamber is a pocket to the side of the piston, above the valves, which is why the section looks like an inverted L and the layout is also called an L-head or a flathead. A T-head is the crossflow version, with inlet and exhaust on opposite sides of the bore. The Ford Model T, the Ford Model A, the Ford flathead V8 and the Morris Eight are sidevalves. The arrangement is simple and compact, and a valve that sticks open does not hit the piston. The breathing is poor, the long exhaust path puts heat into the block, and the chamber shape knocks if the compression ratio is pushed. It is a spark-ignition layout. A diesel chamber needs a compression ratio this shape will not give.
The F-head used in the 1950s by Willys, Rover, Land Rover and Rolls-Royce kept one sidevalve and put the other valve in the head. It is a halfway house, not a later overhead-valve engine with both valves overhead.
Overhead valves
Overhead valves sit in the cylinder head, above the chamber. That is the usual road engine. The cam can still be in the block, reaching the valves with pushrods and rockers, or it can be in the head. Both are overhead-valve engines in the literal sense. The name overhead valve, used alone, has come to mean the pushrod version. An overhead cam is the version with the cam in the head. The difference is the camshaft page, not a different kind of valve.
Two valves
Two valves per cylinder is one inlet and one exhaust. It is the usual pushrod petrol head, because the pushrods and the ports are competing for the same casting, and it is the usual early overhead-cam head. The valves are large, the plug is off to one side, and the rev limit is set by the mass of those two valves and by the train that opens them.
Three valves
Three valves is usually two smaller inlet valves and one large exhaust valve. The head breathes better than a two-valve head. The single exhaust valve is still large, so the rev limit does not move as far as it does with two small exhaust valves. The manufacturing cost can be kept down because one cam can do the job.
The 1975 Honda Civic introduced Honda’s 1.5-litre single-overhead-cam 12-valve four, which is three valves per cylinder. The Maserati Biturbo, from 1981, used three valves for most of its production and later moved to four. Nissan’s KA24E of 1988 to 1992 is a single overhead cam with two inlets and one exhaust. Toyota’s E-series, in some Tercels and Starlets, is the same count. Mercedes-Benz and Ford later used three-valve V6 and V8 engines. Ford’s reason, as the multi-valve account records it, was high-speed breathing without the cost of a second cam. General Motors’ Generation IV V8 did the three-valve count with pushrods and forked rockers, so the cam stayed in the block.
Four valves
Four valves is two inlet and two exhaust, the exhaust pair the same size as the inlets or a little smaller. It is the common multi-valve head. The exhaust valves are small enough to be run faster than one large exhaust valve, and the plug sits in the centre. A single overhead cam can operate them with rockers. The 1973 Triumph Dolomite Sprint is the case usually cited as the first widely available, popularly priced four-cylinder car with four valves per cylinder: a single overhead cam and sixteen valves. Earlier four-valve fours, including the Cosworth BDA in the Ford Escort RS1600 and the Lotus 907 in the 1972 Jensen-Healey, were made in much smaller numbers. A twin cam usually puts a bucket tappet on each valve and does not need a forked rocker.
Four valves does not require an overhead cam. Duramax V8 diesels, the Cummins B series, and the Ford 6.7-litre Power Stroke all use four valves per cylinder with pushrods. The Harley-Davidson Milwaukee-Eight, introduced in 2016, is four valves and a single cam in the block. On those diesels the extra valves are there for emissions and for low-speed torque, not for a motorcycle-style rev limit. A direct injector often sits in the middle of the four valves, which is the space the plug also wants. The 1993 Mercedes-Benz OM604 is recorded as the first four-valve diesel car engine.
Five valves
Five valves is three inlet and two exhaust, all of a similar size. On a simple equal-area comparison that ignores the plug and the injector, two valves cover about half the bore, three about 64 percent, and both four and five about 68 percent. Six is already back down, near 66 percent. Five therefore does not buy a larger geometric area than four. What it does buy is smaller valves, which can be run faster, and three inlet ports. Whether that is worth the extra parts has been argued for as long as the layout has been sold. Direct injection makes the argument harder, because the injector needs a place in a head that is already full.
Mitsubishi sold the first production car engine with five valves per cylinder, the 548 cc 3G81 in the 1989 Minica Dangan ZZ. Yamaha designed the five-valve head for Toyota’s 1.6-litre 4A-GE 20-valve, used in some Corollas in Japan and South Africa from 1991. Audi’s 1.8-litre 20-valve engines, including the turbo, are the same count, as are the later Ferrari Dino V8s and the Bugatti EB110. Yamaha also used five valves in Formula One and on the YZ250F and YZ450F, and then went back to four valves on its later Genesis motorcycle engines because four was cheaper. The five-valve head did not become the ordinary road head. Four did.
The count and the cam are separate
A pushrod engine can have two, three or four valves. A single overhead cam can have two, three or four. A twin cam can have four or five. Choosing a cam layout does not choose the valve count, and adding valves does not by itself move the cam into the head. The cam positions are on camshafts.
Sources
Wikipedia text is paraphrased from the cited articles under CC BY-SA 4.0. Accessed 2026-11-13.
- Multi-valve. Two, three, four and five valves, the equal-area comparison, the 1975 Honda Civic, the Maserati Biturbo, the Nissan KA24E, the Toyota E-series, Ford and Mercedes three-valve engines, the Triumph Dolomite Sprint, the pushrod four-valve diesels, the Milwaukee-Eight, the Mitsubishi 3G81, the Toyota 4A-GE 20-valve, the Audi 1.8 20-valve, and Yamaha’s return to four valves.
- Flathead engine. Sidevalve, L-head and T-head, the offset chamber, Ford and Morris applications, and the F-head.
- Overhead valve engine. Overhead valve as the name for valves in the head with the cam in the block, and the usual two-valve limit on a pushrod petrol engine.