Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
TVR

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

For most of its history TVR bought its engines from other manufacturers: Ford, BMC, Triumph and, from 1983, Rover. Between 1996 and 2006 it built its own: the AJP8 V8, sold as the "Speed Eight", the Speed Six straight six, and the Speed Twelve V12 for its GT racing programme. Before that, its Coventry subsidiary TVR Power enlarged and developed the Rover V8 used in the Griffith, Chimaera and wedge cars. The in-house engines made very high specific outputs (the Speed Six reached about 100 bhp per litre in 4.0-litre S form), but early engines were not durable. Most surviving engines have since been rebuilt to address valvetrain and lubrication faults. For the cars and the company see TVR: history and cars; for injection systems and ECUs see TVR engine management and ECUs.

Origins of the AJP engines

The name AJP comes from the first names of the three people behind the design: Al Melling, whose consultancy MCD did the design work; John Ravenscroft, TVR's engine engineer; and Peter Wheeler, TVR's owner. The V8 was announced in 1994 and went into production in the Cerbera in 1996. A one-off 1994 Griffith was fitted with an AJP V8, but the engine never reached the Griffith or Chimaera in production. A six-cylinder version, developed as the AJP6, became the Speed Six and was first sold in the Cerbera Speed Six from about 1998. Two six-cylinder banks on one crankshaft formed the 7.7-litre Speed Twelve.

AJP8 V8 ("Speed Eight")

ItemAJP8 4.2AJP8 4.54.5 Red Rose Layout75° V8, all-alloy, flat-plane crankshaft, one overhead camshaft per bank, two valves per cylinder Capacity, bore × stroke4,185 cc, 88 × 86 mm4,475 cc, 91 × 86 mm4,475 cc Compression ratio10:110:110.75:1 Power360 bhp at 6,500 rpm420 bhp at 6,750 rpm440 bhp at 7,250 rpm Torque320 lb ft at 4,500 rpm380 lb ft at 5,500 rpm402 lb ft at 5,500 rpm (390 and 406 lb ft also quoted) ApplicationsCerbera 4.2 (1996–2003)Cerbera 4.5 (1997/98–2003); late Tuscan Challenge race carsCerbera 4.5 Red Rose option

Power, torque, capacity and the 75° angle come from TVR's 2005 brochure. Bore, stroke and compression ratios come from secondary references, though the bore and stroke agree with the stated capacities. TVR quoted the engine's weight as 121 kg. A 2025 magazine figure of about 150 kg is unsupported, and the manufacturer figure is preferred. Road tests suggest the claimed outputs are optimistic: evo gave the launch figures as 350 bhp (4.2) and 400 bhp (4.5), and buyers' guides report dynamometer results below the brochure numbers.

The Red Rose specification had reshaped ports, higher compression and two switchable fuel and ignition maps, for 95 and 97 RON petrol. The higher map was selected by an unmarked dashboard button and needs at least 97 RON. TVR Power also sold a "Red Rose Spec" retrofit in 2004, priced at £3,000 plus VAT for the AJP8.

Known problems

Early engines had serious reliability problems, and most have now been rebuilt (buyers' guides, 2017 and 2025). Valve clearances need checking about every 12,000 miles. Early 4.2 crankshaft failures are said to have been cured by enlarging the journals from 2.3 to 2.5 inches. This is a single unverified forum report. Not established: the camshaft drive (chain or belt) and whether road engines are wet- or dry-sumped. The derived Melling V8 was wet-sump for road and dry-sump for racing.

Speed Six straight six

The Speed Six is an all-aluminium straight six with thin-wall cylinder liners. It has twin chain-driven overhead camshafts, four valves per cylinder and finger-follower valve actuation. It is dry-sumped and installed canted over by 15°. It has forged steel connecting rods, slipper pistons, a fully counterweighted nodular-iron crankshaft, and one throttle body and injector per cylinder. The 3.6 revs to 8,000 rpm. Compression ratios of 11.0, 11.8 and 12.2:1 are quoted for different versions, but which ratio belongs to which version has not been documented.

VersionCapacity, bore × strokePowerTorqueApplications 3.63,605 cc, 96 × 83 mm350 bhp at 7,200 rpm290 lb ft at 5,500 rpmTuscan 3.6, Tamora, T350C/T350T 4.0, Cerbera3,996 cc, 96 × 92 mm350 bhp at 6,800 rpm330 lb ft at 5,000 rpmCerbera Speed Six (1998–2003) 4.0, Tuscan3,996 cc360 bhp310 lb ftTuscan Mk1 4.0, Tuscan Convertible 4.0 Red Rose3,996 cc380 bhp310 lb ftTuscan Red Rose, Tuscan Mk2 4.0 4.0 S3,996 cc390 bhp at 7,000 rpm; 400 bhp from 2003310–315 lb ftTuscan S, Tuscan Mk2 S, Sagaris, T400R road car T440RAbout 4.2 litres (brochure text and secondary sources; the brochure table says 3,996 cc)440 bhp at 7,600 rpm350 lb ft at 6,000 rpmT440R Typhon3,996 ccAbout 400 bhp naturally aspirated; 500–585 bhp claimed for the supercharged car—Typhon (three cars)

The Sagaris was listed by TVR at 400 bhp and 310 lb ft. A widely repeated 406 bhp and 349 lb ft comes from a specification database. A press report says TVR's own dynamometer figure for the Sagaris fell from 406 to 386 and then 375 bhp during development, so the true output of production cars is uncertain. Supercharging of the Typhon was dropped because of cooling problems; only one supercharged car is reported, and the other cars used the naturally aspirated 4.0.

Known problems and rebuild practice

Valvetrain oiling. Oil drillings that fed the cam lobes from the camshaft centres were left out of production engines, starving the cams and followers. This is the root cause usually given for poor early durability. An independent study commissioned in 2006 found most failures in the cylinder head and valvetrain. It also reported failures of the half-time bearing from oil starvation. Finger followers. Worn followers cause a poor hot idle, and oily soot at the exhaust tailpipes is a common sign. Mk1 Tuscan engines are reported as the worst affected. The usual repair is steel followers with matching camshafts. Rebuild packages. Several rebuild packages have been offered: Autocraft SVE and MCD: an MCD-approved head, valvetrain and cam-oiling package (2005). Wilder Engineering: revised pressure and scavenge pumps and oil galleries, its own cams and followers, H-beam rods, and lower compression for 95 RON. It kept the standard TVR ECU (2008). Melling Sportscars: a "return to original AJP6 specification" rebuild with the oil galleries reinstated, billet camshafts, a re-machined head, Colsibro valve guides, and optional 4.5 and 4.7-litre versions (2009). Its claimed 516 and 550 bhp are vendor figures. TVR Power: rebuilds with a three-year warranty and 4.3 and 4.5-litre stroker builds of up to about 450 bhp. Other fixes. Harder cam lobes and followers, revised guides, softer valve springs and thicker valve stems are also used. Real-world output. Dynamometer results for individual cars are often below the brochure figures. One owner reported 349 bhp for a Tuscan on its original ECU. A Cerbera Speed Six measured 338 bhp after a 2025 recalibration on a replacement ECU. These are single-car reports; see TVR engine management and ECUs.

Speed Twelve V12

The Speed Twelve is a 7.7-litre V12 (7,730 cc) with a fabricated steel block, built for the Cerbera Speed 12 (also called Project 7/12 and Speed Twelve) shown in 1996. It is generally described as two Speed Six cylinder banks on one crankshaft. One source gives a bore and stroke of 96 × 89 mm, which agrees with the capacity, but whether the heads are Speed Six parts is not established. Five blocks are reported to have been made. TVR claimed 800 bhp or more for the road car. Each bank produced about 480 bhp when tested separately, but the complete engine was never measured, because the dynamometer input shaft broke. The race engines ran with intake restrictors at about 660–675 bhp in British GT from 1998. TVR cancelled the road car, priced at £245,000, after Peter Wheeler judged it undriveable on the road.

Rover V8 engines developed by TVR Power

From the 350i of 1983 to the last Chimaera and Griffith in 2003, TVR's V8 cars used the aluminium Rover V8, a 90° pushrod engine with two valves per cylinder and distributor ignition. TVR Power, in Coventry, enlarged it with longer-stroke crankshafts and larger bores. The capacities quoted by TVR are nominal, and several differ slightly from the bore × stroke arithmetic.

EngineCapacity, bore × strokeQuoted outputUsed in 3.53,528 cc, 88.9 × 71.1 mm190 bhp, later 197 bhp350i 3.9 (390SE)3,905 cc, 93.5 × 71.1 mm275 bhp, 270 lb ft390SE 4.24,228 cc, 93.5 × 77 mmAbout 300 bhp420SE, 420 SEAC 4.5 (SEAC)4,441 cc, 94 × 80 mm324 bhp, 310 lb ft450SE, 450 SEAC 4.03,950 cc nominal, 94 × 71.1 mm240 bhp, 270 lb ft (255 bhp option)400SE, V8S, Griffith 4.0, Chimaera 400 4.0 HC3,950 cc275 bhp (250 bhp in one club source)Griffith and Chimaera 4.0 HC 4.34,280 cc nominal, 94 × 77 mm280 bhp, 305 lb ft; "BV" engines about 300 bhp430SE, Griffith 4.3, Chimaera 430 4.5 (Chimaera)4,546 cc, 94 × 82 mm (4,495 cc also quoted)285 bhp, 310 lb ftChimaera 450, a few Griffiths 5.04,988 cc nominal, 94 × 90 mm340 bhp, 350 lb ft; 320 bhp from 1997 and with catalystsGriffith 500, Chimaera 500

The 5.0 used a 90 mm-stroke crankshaft supplied by TVR Power. It was retuned to 320 bhp in 1997 to improve idle and driveability. A revised "Serpentine" engine with a single-belt accessory drive arrived in 1994. Common faults on these engines are camshaft wear at around 50,000 miles, cam chain stretch at around 100,000 miles, sludged hydraulic lifters, head-gasket failure, cracked exhaust manifolds, heat-soaked starter motors and dirty idle stepper motors. See also Land Rover Rover V8 petrol tuning guide for the shared engine family.

Bought-in engines

All other TVR engines were bought in. The model tables on the main TVR page give each fitment; in outline:

1949–1966: Ford sidevalve 1172 cc; Coventry Climax FWA and FWE; BMC B-series from the MGA and MGB; Ford 105E and 109E Kent; Ford 289 Windsor V8 in the Griffith 200 and 400. 1967–1979: Ford 289 and 302 V8 (Tuscan V8); Ford Kent 1600 crossflow (Vixen, 1600M); Triumph 1300 and 2.5 straight six (Vixen 1300 and 2500, 2500M); Ford Essex 3.0 V6 (Tuscan V6, 3000M, Taimar, 3000S), with a Broadspeed turbocharged version from 1976. 1980–1994: Ford Cologne 2.8 V6 (Tasmin 280i, S1) and 2.9 V6 (S2–S4C); Ford Pinto 2.0 (Tasmin 200). Revived Griffith (revealed 2017): Ford 5.0 Coyote V8, developed by Cosworth with a dry sump, a lightened flywheel and its own calibration. About 500 bhp was expected, but this was never confirmed.

Not established

Cam drive and sump arrangement of the road AJP8. Which compression ratio belongs to which Speed Six version, and a measured oil-consumption figure. Speed Twelve head design and engine-management system. The exact capacity of the 4.5-litre Rover V8 fitted to the Chimaera 450. Production outputs of the Sagaris as delivered.

Sources

TVR 2005 brochure and price list (Tamora, T350, Tuscan, Cerbera, Sagaris, T400R, T440R, Typhon), TVR Motor Company, 2005, hosted by the TVR Car Club (manufacturer document). Accessed 19 November 2026. Ravenscroft, J. (TVR Engineering) and Adams, M., engine tuning articles from Sprint, TVR Car Club magazine, about 1997, reproduced on The TVR SEAC Pages. Accessed 19 November 2026. Wikipedia, TVR Speed Six engine, TVR Speed Eight engine, TVR Cerbera Speed 12, TVR Cerbera, TVR Chimaera and TVR Griffith. Accessed 19 November 2026. Hayward, M., TVR Cerbera 4.5 Red Rose Lightweight, Octane, 30 April 2025. Accessed 19 November 2026. Vivian, D., Birth of an icon: TVR Speed 12, evo, 19 February 2010; and TVR Cerbera (1996–2004) review, evo, updated 2 November 2026. Accessed 19 November 2026. Badree, A., TVR's Speed Six made almost 100 hp per liter, Jalopnik, 20 June 2026. Accessed 19 November 2026. PistonHeads: TVR Tuscan buying guide: powertrain, 31 May 2013; TVR Griffith buying guide: powertrain, 13 April 2011; TVR Chimaera buying guide: powertrain, 3 January 2017; TVR Speed Six gets reliability package, 22 June 2005; New engines based on Speed Six, 8 January 2008; Speed Six engine conversion makes 550bhp, 6 May 2009; Engine upgrades for TVRs, 10 May 2004. Accessed 19 November 2026. TVR Cerbera revived: 338bhp after 15 years without an update, Garage Whifbitz, 14 November 2025. Accessed 19 November 2026. TVR 390 SE, Motor Sport, May 1985; Rover V8 capacity table, Seight.com. Accessed 19 November 2026. TVR returns with V8-powered Griffith, GoAuto, 11 September 2017. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: TVR engines: AJP8, Speed Six, Speed Twelve and Rover V8

For most of its history TVR bought its engines from other manufacturers: Ford, BMC, Triumph and, from 1983, Rover. Between 1996 and 2006 it built its own: the AJP8 V8, sold as the "Speed Eight", the Speed Six straight six, and the Speed Twelve V12 for its GT racing programme. Before that, its Coventry subsidiary TVR Power enlarged and developed the Rover V8 used in the Griffith, Chimaera and wedge cars. The in-house engines made very high specific outputs (the Speed Six reached about 100 bhp per litre in 4.0-litre S form), but early engines were not durable. Most surviving engines have since been rebuilt to address valvetrain and lubrication faults. For the cars and the company see TVR: history and cars; for injection systems and ECUs see TVR engine management and ECUs.

Origins of the AJP engines

The name AJP comes from the first names of the three people behind the design: Al Melling, whose consultancy MCD did the design work; John Ravenscroft, TVR's engine engineer; and Peter Wheeler, TVR's owner. The V8 was announced in 1994 and went into production in the Cerbera in 1996. A one-off 1994 Griffith was fitted with an AJP V8, but the engine never reached the Griffith or Chimaera in production. A six-cylinder version, developed as the AJP6, became the Speed Six and was first sold in the Cerbera Speed Six from about 1998. Two six-cylinder banks on one crankshaft formed the 7.7-litre Speed Twelve.

AJP8 V8 ("Speed Eight")

ItemAJP8 4.2AJP8 4.54.5 Red Rose
Layout75° V8, all-alloy, flat-plane crankshaft, one overhead camshaft per bank, two valves per cylinder
Capacity, bore × stroke4,185 cc, 88 × 86 mm4,475 cc, 91 × 86 mm4,475 cc
Compression ratio10:110:110.75:1
Power360 bhp at 6,500 rpm420 bhp at 6,750 rpm440 bhp at 7,250 rpm
Torque320 lb ft at 4,500 rpm380 lb ft at 5,500 rpm402 lb ft at 5,500 rpm (390 and 406 lb ft also quoted)
ApplicationsCerbera 4.2 (1996–2003)Cerbera 4.5 (1997/98–2003); late Tuscan Challenge race carsCerbera 4.5 Red Rose option

Power, torque, capacity and the 75° angle come from TVR's 2005 brochure. Bore, stroke and compression ratios come from secondary references, though the bore and stroke agree with the stated capacities. TVR quoted the engine's weight as 121 kg. A 2025 magazine figure of about 150 kg is unsupported, and the manufacturer figure is preferred. Road tests suggest the claimed outputs are optimistic: evo gave the launch figures as 350 bhp (4.2) and 400 bhp (4.5), and buyers' guides report dynamometer results below the brochure numbers.

The Red Rose specification had reshaped ports, higher compression and two switchable fuel and ignition maps, for 95 and 97 RON petrol. The higher map was selected by an unmarked dashboard button and needs at least 97 RON. TVR Power also sold a "Red Rose Spec" retrofit in 2004, priced at £3,000 plus VAT for the AJP8.

Known problems

  • Early engines had serious reliability problems, and most have now been rebuilt (buyers' guides, 2017 and 2025).
  • Valve clearances need checking about every 12,000 miles.
  • Early 4.2 crankshaft failures are said to have been cured by enlarging the journals from 2.3 to 2.5 inches. This is a single unverified forum report.
  • Not established: the camshaft drive (chain or belt) and whether road engines are wet- or dry-sumped. The derived Melling V8 was wet-sump for road and dry-sump for racing.

Speed Six straight six

The Speed Six is an all-aluminium straight six with thin-wall cylinder liners. It has twin chain-driven overhead camshafts, four valves per cylinder and finger-follower valve actuation. It is dry-sumped and installed canted over by 15°. It has forged steel connecting rods, slipper pistons, a fully counterweighted nodular-iron crankshaft, and one throttle body and injector per cylinder. The 3.6 revs to 8,000 rpm. Compression ratios of 11.0, 11.8 and 12.2:1 are quoted for different versions, but which ratio belongs to which version has not been documented.

VersionCapacity, bore × strokePowerTorqueApplications
3.63,605 cc, 96 × 83 mm350 bhp at 7,200 rpm290 lb ft at 5,500 rpmTuscan 3.6, Tamora, T350C/T350T
4.0, Cerbera3,996 cc, 96 × 92 mm350 bhp at 6,800 rpm330 lb ft at 5,000 rpmCerbera Speed Six (1998–2003)
4.0, Tuscan3,996 cc360 bhp310 lb ftTuscan Mk1 4.0, Tuscan Convertible
4.0 Red Rose3,996 cc380 bhp310 lb ftTuscan Red Rose, Tuscan Mk2 4.0
4.0 S3,996 cc390 bhp at 7,000 rpm; 400 bhp from 2003310–315 lb ftTuscan S, Tuscan Mk2 S, Sagaris, T400R road car
T440RAbout 4.2 litres (brochure text and secondary sources; the brochure table says 3,996 cc)440 bhp at 7,600 rpm350 lb ft at 6,000 rpmT440R
Typhon3,996 ccAbout 400 bhp naturally aspirated; 500–585 bhp claimed for the supercharged car—Typhon (three cars)

The Sagaris was listed by TVR at 400 bhp and 310 lb ft. A widely repeated 406 bhp and 349 lb ft comes from a specification database. A press report says TVR's own dynamometer figure for the Sagaris fell from 406 to 386 and then 375 bhp during development, so the true output of production cars is uncertain. Supercharging of the Typhon was dropped because of cooling problems; only one supercharged car is reported, and the other cars used the naturally aspirated 4.0.

Known problems and rebuild practice

  • Valvetrain oiling. Oil drillings that fed the cam lobes from the camshaft centres were left out of production engines, starving the cams and followers. This is the root cause usually given for poor early durability. An independent study commissioned in 2006 found most failures in the cylinder head and valvetrain. It also reported failures of the half-time bearing from oil starvation.
  • Finger followers. Worn followers cause a poor hot idle, and oily soot at the exhaust tailpipes is a common sign. Mk1 Tuscan engines are reported as the worst affected. The usual repair is steel followers with matching camshafts.
  • Rebuild packages. Several rebuild packages have been offered:
    • Autocraft SVE and MCD: an MCD-approved head, valvetrain and cam-oiling package (2005).
    • Wilder Engineering: revised pressure and scavenge pumps and oil galleries, its own cams and followers, H-beam rods, and lower compression for 95 RON. It kept the standard TVR ECU (2008).
    • Melling Sportscars: a "return to original AJP6 specification" rebuild with the oil galleries reinstated, billet camshafts, a re-machined head, Colsibro valve guides, and optional 4.5 and 4.7-litre versions (2009). Its claimed 516 and 550 bhp are vendor figures.
    • TVR Power: rebuilds with a three-year warranty and 4.3 and 4.5-litre stroker builds of up to about 450 bhp.
  • Other fixes. Harder cam lobes and followers, revised guides, softer valve springs and thicker valve stems are also used.
  • Real-world output. Dynamometer results for individual cars are often below the brochure figures. One owner reported 349 bhp for a Tuscan on its original ECU. A Cerbera Speed Six measured 338 bhp after a 2025 recalibration on a replacement ECU. These are single-car reports; see TVR engine management and ECUs.

Speed Twelve V12

The Speed Twelve is a 7.7-litre V12 (7,730 cc) with a fabricated steel block, built for the Cerbera Speed 12 (also called Project 7/12 and Speed Twelve) shown in 1996. It is generally described as two Speed Six cylinder banks on one crankshaft. One source gives a bore and stroke of 96 × 89 mm, which agrees with the capacity, but whether the heads are Speed Six parts is not established. Five blocks are reported to have been made. TVR claimed 800 bhp or more for the road car. Each bank produced about 480 bhp when tested separately, but the complete engine was never measured, because the dynamometer input shaft broke. The race engines ran with intake restrictors at about 660–675 bhp in British GT from 1998. TVR cancelled the road car, priced at £245,000, after Peter Wheeler judged it undriveable on the road.

Rover V8 engines developed by TVR Power

From the 350i of 1983 to the last Chimaera and Griffith in 2003, TVR's V8 cars used the aluminium Rover V8, a 90° pushrod engine with two valves per cylinder and distributor ignition. TVR Power, in Coventry, enlarged it with longer-stroke crankshafts and larger bores. The capacities quoted by TVR are nominal, and several differ slightly from the bore × stroke arithmetic.

EngineCapacity, bore × strokeQuoted outputUsed in
3.53,528 cc, 88.9 × 71.1 mm190 bhp, later 197 bhp350i
3.9 (390SE)3,905 cc, 93.5 × 71.1 mm275 bhp, 270 lb ft390SE
4.24,228 cc, 93.5 × 77 mmAbout 300 bhp420SE, 420 SEAC
4.5 (SEAC)4,441 cc, 94 × 80 mm324 bhp, 310 lb ft450SE, 450 SEAC
4.03,950 cc nominal, 94 × 71.1 mm240 bhp, 270 lb ft (255 bhp option)400SE, V8S, Griffith 4.0, Chimaera 400
4.0 HC3,950 cc275 bhp (250 bhp in one club source)Griffith and Chimaera 4.0 HC
4.34,280 cc nominal, 94 × 77 mm280 bhp, 305 lb ft; "BV" engines about 300 bhp430SE, Griffith 4.3, Chimaera 430
4.5 (Chimaera)4,546 cc, 94 × 82 mm (4,495 cc also quoted)285 bhp, 310 lb ftChimaera 450, a few Griffiths
5.04,988 cc nominal, 94 × 90 mm340 bhp, 350 lb ft; 320 bhp from 1997 and with catalystsGriffith 500, Chimaera 500

The 5.0 used a 90 mm-stroke crankshaft supplied by TVR Power. It was retuned to 320 bhp in 1997 to improve idle and driveability. A revised "Serpentine" engine with a single-belt accessory drive arrived in 1994. Common faults on these engines are camshaft wear at around 50,000 miles, cam chain stretch at around 100,000 miles, sludged hydraulic lifters, head-gasket failure, cracked exhaust manifolds, heat-soaked starter motors and dirty idle stepper motors. See also Land Rover Rover V8 petrol tuning guide for the shared engine family.

Bought-in engines

All other TVR engines were bought in. The model tables on the main TVR page give each fitment; in outline:

  • 1949–1966: Ford sidevalve 1172 cc; Coventry Climax FWA and FWE; BMC B-series from the MGA and MGB; Ford 105E and 109E Kent; Ford 289 Windsor V8 in the Griffith 200 and 400.
  • 1967–1979: Ford 289 and 302 V8 (Tuscan V8); Ford Kent 1600 crossflow (Vixen, 1600M); Triumph 1300 and 2.5 straight six (Vixen 1300 and 2500, 2500M); Ford Essex 3.0 V6 (Tuscan V6, 3000M, Taimar, 3000S), with a Broadspeed turbocharged version from 1976.
  • 1980–1994: Ford Cologne 2.8 V6 (Tasmin 280i, S1) and 2.9 V6 (S2–S4C); Ford Pinto 2.0 (Tasmin 200).
  • Revived Griffith (revealed 2017): Ford 5.0 Coyote V8, developed by Cosworth with a dry sump, a lightened flywheel and its own calibration. About 500 bhp was expected, but this was never confirmed.

Not established

  • Cam drive and sump arrangement of the road AJP8.
  • Which compression ratio belongs to which Speed Six version, and a measured oil-consumption figure.
  • Speed Twelve head design and engine-management system.
  • The exact capacity of the 4.5-litre Rover V8 fitted to the Chimaera 450.
  • Production outputs of the Sagaris as delivered.

Sources

Revision 1: TVR engines: AJP8, Speed Six, Speed Twelve and Rover V8

For most of its history TVR bought its engines from other manufacturers: Ford, BMC, Triumph and, from 1983, Rover. Between 1996 and 2006 it built its own: the AJP8 V8, sold as the "Speed Eight", the Speed Six straight six, and the Speed Twelve V12 for its GT racing programme. Before that, its Coventry subsidiary TVR Power enlarged and developed the Rover V8 used in the Griffith, Chimaera and wedge cars. The in-house engines made very high specific outputs (the Speed Six reached about 100 bhp per litre in 4.0-litre S form), but early engines were not durable. Most surviving engines have since been rebuilt to address valvetrain and lubrication faults. For the cars and the company see TVR: history and cars; for injection systems and ECUs see TVR engine management and ECUs.

Origins of the AJP engines

The name AJP comes from the first names of the three people behind the design: Al Melling, whose consultancy MCD did the design work; John Ravenscroft, TVR's engine engineer; and Peter Wheeler, TVR's owner. The V8 was announced in 1994 and went into production in the Cerbera in 1996. A one-off 1994 Griffith was fitted with an AJP V8, but the engine never reached the Griffith or Chimaera in production. A six-cylinder version, developed as the AJP6, became the Speed Six and was first sold in the Cerbera Speed Six from about 1998. Two six-cylinder banks on one crankshaft formed the 7.7-litre Speed Twelve.

AJP8 V8 ("Speed Eight")

ItemAJP8 4.2AJP8 4.54.5 Red Rose
Layout75° V8, all-alloy, flat-plane crankshaft, one overhead camshaft per bank, two valves per cylinder
Capacity, bore × stroke4,185 cc, 88 × 86 mm4,475 cc, 91 × 86 mm4,475 cc
Compression ratio10:110:110.75:1
Power360 bhp at 6,500 rpm420 bhp at 6,750 rpm440 bhp at 7,250 rpm
Torque320 lb ft at 4,500 rpm380 lb ft at 5,500 rpm402 lb ft at 5,500 rpm (390 and 406 lb ft also quoted)
ApplicationsCerbera 4.2 (1996–2003)Cerbera 4.5 (1997/98–2003); late Tuscan Challenge race carsCerbera 4.5 Red Rose option

Power, torque, capacity and the 75° angle come from TVR's 2005 brochure. Bore, stroke and compression ratios come from secondary references, though the bore and stroke agree with the stated capacities. TVR quoted the engine's weight as 121 kg. A 2025 magazine figure of about 150 kg is unsupported, and the manufacturer figure is preferred. Road tests suggest the claimed outputs are optimistic: evo gave the launch figures as 350 bhp (4.2) and 400 bhp (4.5), and buyers' guides report dynamometer results below the brochure numbers.

The Red Rose specification had reshaped ports, higher compression and two switchable fuel and ignition maps, for 95 and 97 RON petrol. The higher map was selected by an unmarked dashboard button and needs at least 97 RON. TVR Power also sold a "Red Rose Spec" retrofit in 2004, priced at £3,000 plus VAT for the AJP8.

Known problems

  • Early engines had serious reliability problems, and most have now been rebuilt (buyers' guides, 2017 and 2025).
  • Valve clearances need checking about every 12,000 miles.
  • Early 4.2 crankshaft failures are said to have been cured by enlarging the journals from 2.3 to 2.5 inches. This is a single unverified forum report.
  • Not established: the camshaft drive (chain or belt) and whether road engines are wet- or dry-sumped. The derived Melling V8 was wet-sump for road and dry-sump for racing.

Speed Six straight six

The Speed Six is an all-aluminium straight six with thin-wall cylinder liners. It has twin chain-driven overhead camshafts, four valves per cylinder and finger-follower valve actuation. It is dry-sumped and installed canted over by 15°. It has forged steel connecting rods, slipper pistons, a fully counterweighted nodular-iron crankshaft, and one throttle body and injector per cylinder. The 3.6 revs to 8,000 rpm. Compression ratios of 11.0, 11.8 and 12.2:1 are quoted for different versions, but which ratio belongs to which version has not been documented.

VersionCapacity, bore × strokePowerTorqueApplications
3.63,605 cc, 96 × 83 mm350 bhp at 7,200 rpm290 lb ft at 5,500 rpmTuscan 3.6, Tamora, T350C/T350T
4.0, Cerbera3,996 cc, 96 × 92 mm350 bhp at 6,800 rpm330 lb ft at 5,000 rpmCerbera Speed Six (1998–2003)
4.0, Tuscan3,996 cc360 bhp310 lb ftTuscan Mk1 4.0, Tuscan Convertible
4.0 Red Rose3,996 cc380 bhp310 lb ftTuscan Red Rose, Tuscan Mk2 4.0
4.0 S3,996 cc390 bhp at 7,000 rpm; 400 bhp from 2003310–315 lb ftTuscan S, Tuscan Mk2 S, Sagaris, T400R road car
T440RAbout 4.2 litres (brochure text and secondary sources; the brochure table says 3,996 cc)440 bhp at 7,600 rpm350 lb ft at 6,000 rpmT440R
Typhon3,996 ccAbout 400 bhp naturally aspirated; 500–585 bhp claimed for the supercharged car—Typhon (three cars)

The Sagaris was listed by TVR at 400 bhp and 310 lb ft. A widely repeated 406 bhp and 349 lb ft comes from a specification database. A press report says TVR's own dynamometer figure for the Sagaris fell from 406 to 386 and then 375 bhp during development, so the true output of production cars is uncertain. Supercharging of the Typhon was dropped because of cooling problems; only one supercharged car is reported, and the other cars used the naturally aspirated 4.0.

Known problems and rebuild practice

  • Valvetrain oiling. Oil drillings that fed the cam lobes from the camshaft centres were left out of production engines, starving the cams and followers. This is the root cause usually given for poor early durability. An independent study commissioned in 2006 found most failures in the cylinder head and valvetrain. It also reported failures of the half-time bearing from oil starvation.
  • Finger followers. Worn followers cause a poor hot idle, and oily soot at the exhaust tailpipes is a common sign. Mk1 Tuscan engines are reported as the worst affected. The usual repair is steel followers with matching camshafts.
  • Rebuild packages. Several rebuild packages have been offered:
    • Autocraft SVE and MCD: an MCD-approved head, valvetrain and cam-oiling package (2005).
    • Wilder Engineering: revised pressure and scavenge pumps and oil galleries, its own cams and followers, H-beam rods, and lower compression for 95 RON. It kept the standard TVR ECU (2008).
    • Melling Sportscars: a "return to original AJP6 specification" rebuild with the oil galleries reinstated, billet camshafts, a re-machined head, Colsibro valve guides, and optional 4.5 and 4.7-litre versions (2009). Its claimed 516 and 550 bhp are vendor figures.
    • TVR Power: rebuilds with a three-year warranty and 4.3 and 4.5-litre stroker builds of up to about 450 bhp.
  • Other fixes. Harder cam lobes and followers, revised guides, softer valve springs and thicker valve stems are also used.
  • Real-world output. Dynamometer results for individual cars are often below the brochure figures. One owner reported 349 bhp for a Tuscan on its original ECU. A Cerbera Speed Six measured 338 bhp after a 2025 recalibration on a replacement ECU. These are single-car reports; see TVR engine management and ECUs.

Speed Twelve V12

The Speed Twelve is a 7.7-litre V12 (7,730 cc) with a fabricated steel block, built for the Cerbera Speed 12 (also called Project 7/12 and Speed Twelve) shown in 1996. It is generally described as two Speed Six cylinder banks on one crankshaft. One source gives a bore and stroke of 96 × 89 mm, which agrees with the capacity, but whether the heads are Speed Six parts is not established. Five blocks are reported to have been made. TVR claimed 800 bhp or more for the road car. Each bank produced about 480 bhp when tested separately, but the complete engine was never measured, because the dynamometer input shaft broke. The race engines ran with intake restrictors at about 660–675 bhp in British GT from 1998. TVR cancelled the road car, priced at £245,000, after Peter Wheeler judged it undriveable on the road.

Rover V8 engines developed by TVR Power

From the 350i of 1983 to the last Chimaera and Griffith in 2003, TVR's V8 cars used the aluminium Rover V8, a 90° pushrod engine with two valves per cylinder and distributor ignition. TVR Power, in Coventry, enlarged it with longer-stroke crankshafts and larger bores. The capacities quoted by TVR are nominal, and several differ slightly from the bore × stroke arithmetic.

EngineCapacity, bore × strokeQuoted outputUsed in
3.53,528 cc, 88.9 × 71.1 mm190 bhp, later 197 bhp350i
3.9 (390SE)3,905 cc, 93.5 × 71.1 mm275 bhp, 270 lb ft390SE
4.24,228 cc, 93.5 × 77 mmAbout 300 bhp420SE, 420 SEAC
4.5 (SEAC)4,441 cc, 94 × 80 mm324 bhp, 310 lb ft450SE, 450 SEAC
4.03,950 cc nominal, 94 × 71.1 mm240 bhp, 270 lb ft (255 bhp option)400SE, V8S, Griffith 4.0, Chimaera 400
4.0 HC3,950 cc275 bhp (250 bhp in one club source)Griffith and Chimaera 4.0 HC
4.34,280 cc nominal, 94 × 77 mm280 bhp, 305 lb ft; "BV" engines about 300 bhp430SE, Griffith 4.3, Chimaera 430
4.5 (Chimaera)4,546 cc, 94 × 82 mm (4,495 cc also quoted)285 bhp, 310 lb ftChimaera 450, a few Griffiths
5.04,988 cc nominal, 94 × 90 mm340 bhp, 350 lb ft; 320 bhp from 1997 and with catalystsGriffith 500, Chimaera 500

The 5.0 used a 90 mm-stroke crankshaft supplied by TVR Power. It was retuned to 320 bhp in 1997 to improve idle and driveability. A revised "Serpentine" engine with a single-belt accessory drive arrived in 1994. Common faults on these engines are camshaft wear at around 50,000 miles, cam chain stretch at around 100,000 miles, sludged hydraulic lifters, head-gasket failure, cracked exhaust manifolds, heat-soaked starter motors and dirty idle stepper motors. See also Land Rover Rover V8 petrol tuning guide for the shared engine family.

Bought-in engines

All other TVR engines were bought in. The model tables on the main TVR page give each fitment; in outline:

  • 1949–1966: Ford sidevalve 1172 cc; Coventry Climax FWA and FWE; BMC B-series from the MGA and MGB; Ford 105E and 109E Kent; Ford 289 Windsor V8 in the Griffith 200 and 400.
  • 1967–1979: Ford 289 and 302 V8 (Tuscan V8); Ford Kent 1600 crossflow (Vixen, 1600M); Triumph 1300 and 2.5 straight six (Vixen 1300 and 2500, 2500M); Ford Essex 3.0 V6 (Tuscan V6, 3000M, Taimar, 3000S), with a Broadspeed turbocharged version from 1976.
  • 1980–1994: Ford Cologne 2.8 V6 (Tasmin 280i, S1) and 2.9 V6 (S2–S4C); Ford Pinto 2.0 (Tasmin 200).
  • Revived Griffith (revealed 2017): Ford 5.0 Coyote V8, developed by Cosworth with a dry sump, a lightened flywheel and its own calibration. About 500 bhp was expected, but this was never confirmed.

Not established

  • Cam drive and sump arrangement of the road AJP8.
  • Which compression ratio belongs to which Speed Six version, and a measured oil-consumption figure.
  • Speed Twelve head design and engine-management system.
  • The exact capacity of the 4.5-litre Rover V8 fitted to the Chimaera 450.
  • Production outputs of the Sagaris as delivered.

Sources