Tuning Wiki
Browse TVR
Applies to

Check the hardware and software limits stated in this article.

Fuel-injected TVRs used five families of engine management:

  • Bosch K-Jetronic mechanical injection on the Ford Cologne 2.8 V6;
  • Ford electronic injection on the 2.9 V6;
  • Lucas flap-meter injection, then the Lucas 14CUX hot-wire system, on the Rover V8;
  • TVR-specific MBE (Management by Engineering) controllers on the AJP8 V8 and Speed Six engines;
  • a Cosworth calibration of the Ford Coyote V8 for the revived Griffith, which had not entered production by November 2026.

None of these cars has OBD-II diagnostics. The 14CUX and MBE units each use their own serial data link. The engines themselves are covered in TVR engines, and the cars in TVR: history and cars.

Summary by model

Model (years)EngineEngine managementEvidence
Tasmin 280i (1980–87), S / S1 (1986–88)Ford Cologne 2.8 V6Bosch K-Jetronic continuous mechanical injection, no fuelling ECUSpecialist engine reference; follows the Ford 2.8i donor
S2, S3/S3C, S4C (1988–94)Ford Cologne 2.9 V6Ford electronic injection with a vane airflow meter (Ford 86GB-12B529-AA / Bosch 0 280 200 047 on the S2) and Bosch injectors; probably Ford EEC-IVTVR Car Club parts list; ECU type not confirmed
350i, 390SE, 400SE, 420SE/SEAC, 450SE/SEAC (1983–91)Rover V8 3.5–4.5Lucas flap-meter injection, identified as the Lucas 4CU (a TVR-modified Range Rover unit); some late cars have the 14CUXOwner reports; TVR engineer's note on late 400s
V8S (1991–94), Griffith (1991–2002), Chimaera (1992–2003)Rover V8 4.0–5.0Lucas 14CUX hot-wire injection, fuel only, distributor ignitionTVR Engineering article; specialist and encyclopaedic sources agree
Cerbera 4.2 and 4.5 (1996–2003)AJP8 V8MBE, TVR-specific; dual 95/97 RON maps on the Red RoseSpecialist retailer; owner tools
Cerbera Speed Six, Tuscan, Tamora, T350, Sagaris, T400R/T440R, Typhon (1998–2006)Speed SixMBE, TVR-specificSpecialist; owner reports
Cerbera Speed 12Speed Twelve V12Not established—
Griffith (revealed 2017, not delivered)Ford 5.0 Coyote V8, Cosworth-developedDescribed by TVR as a "custom ECU" calibrated by Cosworth; hardware not identifiedManufacturer and press

Carburettor cars (up to 1979, plus the Tasmin 200) are outside this page. The 1976–79 Broadspeed Turbo M-series cars used a carburettor sealed in a pressurised box, not fuel injection.

Ford V6 cars

The Tasmin 280i and S1 used the Ford 2.8i Cologne V6 with Bosch K-Jetronic. This system meters fuel mechanically through an airflow sensor plate and fuel distributor, so there is no fuelling map to edit. Mixture changes are made through control pressure and distributor adjustment, as on other K-Jetronic cars. One owner reports that the injection hardware came from the Granada rather than the Capri, but this is unverified.

The S2 introduced the 2.9 V6 with electronic injection. TVR Car Club's parts list gives the S2 vane airflow meter as Ford 86GB-12B529-AA (Bosch 0 280 200 047) and Bosch 0 280 150-series injectors. It refers to the controller only as the Ford EEC module. European Ford 2.9 V6s generally used EEC-IV with L-Jetronic-type sensors, so EEC-IV is likely, but no TVR-specific designation has been found. A 2003 dynamometer report described one S3C fitted with a South African Ford Falcon 60-pin unit, and a piggy-back controller on that car raised output from 149.8 to 171.4 bhp. Whether the Falcon unit was original equipment is not established.

Rover V8 wedges: Lucas flap-meter injection

The 350i of 1983 used Lucas electronic injection with a vane ("flapper") airflow meter, as on the Rover SD1 Vitesse and the Range Rover of the period. Owners identify the controller as a Lucas 4CU-type unit modified by TVR; one TVR change reportedly removed a road-speed limiter. A part number of ETC4483 is reported by a single owner and is unverified. The larger 390SE, 420 and 450 engines used larger injectors and modified electronics. The SEAC cars are described as having TVR-modified injection.

The change from flap meter to 14CUX hot-wire injection did not happen at a single date. TVR's own engine engineer listed "late model 400s" among the cars that need a 14CUX idle-control update, yet at least one 1989-built 400SE is described with a flap meter. Identify the system on the car itself: a 14CUX car has a hot-wire airflow meter and a 40-pin ECU.

Lucas 14CUX on the Griffith, Chimaera and V8S

TVR's engine engineer wrote that the 14CUX was used by all later TVR Rover V8 models, and no evidence has been found of a factory change to another system on late Chimaeras or the Griffith 500. The 14CUX controls fuel only, using batch-fired injectors in two banks and a hot-wire airflow meter. Ignition is by distributor. The ECU uses a Motorola MC6803U4 processor with the calibration in a 27C128 or 27C256 EPROM. General operation, fault codes and connector details are covered on the Lucas 14CUX page; the points below are specific to TVR.

  • Socketed EPROM. According to TVR Engineering, all TVR 14CUX units have a socketed EPROM holder, unlike standard Range Rover units, so the calibration can be changed by swapping the chip. Land Rover parts data lists ECU AMR 2175 for the Morgan Plus 8 and TVR Chimaera (1991–2000) as the variant with an easily replaced EPROM.
  • Tune resistor. TVR used only two tune resistors: 470 Ω for non-catalyst and 3.9 kΩ for catalyst cars. This matches the Land Rover table, which also lists 910 Ω (Saudi) and 180 Ω (Australia and rest of the world). The resistor sits between ECU pins 5 and 27. If it is missing or out of range, the ECU logs fault code 21 and runs a default map, which is a catalyst map, so a non-catalyst car runs rich.
  • Chips. TVR supplied factory chips for every engine variant. Aftermarket chip sets for TVR and Morgan 14CUX applications are also sold. The calibration cannot be changed over the serial link. Any map change means burning a new EPROM, with a checksum byte that makes the ROM sum to 0x01.
  • Large engines. TVR scaled the airflow-meter input for engines of 4.5 litres and above. A tuner writing in the TVR club magazine advised moving the full-load enrichment switch point from 4.6 V to 3.6 V for 4.3–5.0-litre engines with large throttle bodies, and recalibrating the airflow meter on 5.0-litre engines.
  • Ignition timing. TVR Engineering reported peak power at 30–33° total advance on most TVR Rover V8s. Timing is set at the distributor, not by the ECU.

The 14CUX has a five-pin diagnostic connector carrying 7,812.5 baud inverted serial data. The open-source RoverGauge program, built on the libcomm14cux library, reads live data and fault codes and can write to RAM, but cannot change the stored maps. Engines heavily modified beyond the 14CUX's range are often converted to programmable management. Owners' guides mention Emerald, and an MBE-based system from Powers Performance, for the Chimaera.

MBE on the AJP8 and Speed Six

From the launch of the Cerbera V8 in 1996, TVR used controllers from MBE (Management by Engineering) with TVR-specific hardware and software. The same family covers every AJP8 and Speed Six car. Owners describe three hardware generations:

  • a blue anodised alloy case with one large connector;
  • a blue painted steel case with one connector;
  • a later silver wedge-shaped case with three connectors.

One Tuscan Mk1 unit is labelled "MBE 2F71B6". A TVR part number of E6500 for a Tuscan Mk1 4.0 ECU appears only in a sales listing. The base MBE model is not established. The developer of an owner diagnostic tool, who decoded the serial protocol, describes the unit as based on MBE's 941 but different, and a community reference calls it 9A4/967-style. No TVR unit has been found carrying a 9A4 or 967 label.

Memory and adaptive data

  • Program EPROM. Each ECU carries a socketed EPROM holding the program and maps. 32 KB and doubled 64 KB images exist. Chips are calibration-specific: separate chips are reported for the 3.6 (T350, Tamora), the 4.0 S and the Red Rose. One owner believes the S and Red Rose engines also use different injectors. TVR specialists list a replacement memory chip under part E6549 MC.
  • Adaptive memory. A Dallas DS1230AB non-volatile SRAM holds learned corrections and service settings. Its internal lithium cell lasts roughly ten years. When the cell fails, the learned values are lost at every start, causing poor starting and rough running. Replacing the chip is a known cure, reported on a 1998 Cerbera whose chip was renewed in 2025.

Control strategy and remapping

A specialist ECU repairer states that TVR's MBE calibrations run closed-loop lambda control at all times to a fixed λ = 1 target. Every sensor, including both lambda sensors, must therefore work. The same source says that, because the closed loop learns back towards λ = 1, map changes have little lasting effect, and that the memory storing lambda corrections wears out with age. Owners nevertheless report specialist remaps of the factory units, usually alongside hardware changes. One Cerbera remapped with new throttle bodies and injectors went from 313 to 343 bhp on a dynamometer and was cured of a misfire. Because the hardware changed at the same time, that result does not show what the remap alone achieved.

Injection firing is disputed. A Speed Six owner who converted to aftermarket management reports that the standard system fires six injectors from two drivers. A community transcription of the MBE pinout from a V8 loom also shows two bank injector drivers. A magazine specification lists the Tuscan S as having sequential injection. The two technical sources favour bank or batch firing on standard units, but the S and Red Rose calibrations have not been checked. Any differences between the Sagaris and Tuscan 2 ECUs are not established. A TVR specialist is reported to say that one chip and one ECU suit all late cars.

Diagnostics

The MBE units use an RS-232 serial link (receive, transmit and ground only). TVR's dealer diagnostic software circulates within the owner community and is reported to cover both the Speed Six and the AJP8. Owner-written tools include MBETool (from December 2013), which reads live data, clears fault logs, resets adaptive maps and the throttle, and logs to CSV, but cannot write maps. The RS-AJP Android app covers both engines. MBE's Easimap software is known to read locked MBE units on some other makes, but no source confirms that it works with TVR units.

Revived Griffith

The Griffith revealed in 2017 uses a Ford 5.0 Coyote V8 reworked by Cosworth with a dry sump and a lightened flywheel. TVR describes the engine management as a "custom ECU", and press coverage refers to Cosworth tuning the ECU. It has not been established whether this is a recalibrated Ford controller or Cosworth hardware. No customer cars had been delivered by November 2026.

Aftermarket replacements

SystemApplicationNotes
Syvecs S6GP (via Racing Green TVR)Speed Six and AJP8; Rover V8 suggestedAdds sequential injection, knock control and traction control. Listed at £4,497 ex VAT fitted, currently out of stock. One owner claims 349 bhp on MBE and 376 bhp on Syvecs for a Tuscan (single report).
Omex 710 (via Racing Green TVR)Speed Six cars from 2001Listed at £2,944 ex VAT; now shown as unavailable.
Emerald K6Reported on a 2001 Cerbera 4.5 AJP8; recommended by owners for the ChimaeraThe Cerbera fitment was reportedly made because MBE said parts for the TVR-specific unit were unlikely to be available. This rests on a single unverified article.
MBE-based system (Powers Performance)Rover V8 Chimaera and GriffithRecommended in a 2017 buyers' guide. Powers Performance also repairs TVR MBE units.

No TVR-specific application evidence was found for DTAFast, Canems, MoTeC or Life Racing systems, although such conversions may exist.

Cautions

  • Before changing anything on a Speed Six or AJP8 that runs badly, check the DS1230AB adaptive memory chip, both lambda sensors and the throttle-position calibration. The closed-loop strategy masks a faulty sensor until the corrections run out.
  • On 14CUX cars, confirm the tune resistor value and the socketed chip before diagnosing fuelling. A wrong or missing resistor gives a rich default map and fault 21.
  • Chips are calibration-specific. A Red Rose or S chip in a standard engine, or a non-catalyst chip in a catalyst car, gives incorrect fuelling.

Not established

  • The exact Ford ECU designation on the S2 to S4C.
  • The production date of the flap-meter to hot-wire change on the wedges.
  • The base MBE model, an official TVR/MBE part-number list, and whether any standard calibration fires sequentially.
  • Engine management on the Speed Twelve and the revived Griffith.

Sources