Removed text is struck through; added text is highlighted.
GEMS EM112 product image. Source: GEMS Performance Electronics; used with permission.
GEMS EM112: An eight-cylinder engine-management system with dual wideband lambda, eight coil drivers, eight programmable peak-and-hold injector drivers, three CAN buses and 256 MB internal logging. Manufacturer source.
Hardware and control
GEMS lists 20 analogue inputs, two differential analogue inputs, twelve timing inputs, two knock inputs and a 112-position Molex connector. It supports electronic throttle, variable cam timing and gearshift control, subject to ECU configuration. GEMS model information.
GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.
Connector and pinout
The EM112 technical specification, 103715 rev 11 includes model-specific connector and pinout drawings. Establish connector view, hardware revision and current limits in that document. The EM112 datasheet's connector C ignition driver names and software codes are internally inconsistent at some positions. Do not resolve them by assumption; obtain a confirmed drawing for the actual build from GEMS before connecting ignition.
Source discrepancies: Rev 11 labels connector A H1 and connector C H1 both as ignition coil driver 4, and assigns repeated software codes to other coil and injector outputs. These values are reproduced as printed, not reconciled; ask GEMS for the confirmed drawing for the unit before wiring. The original diagram includes orientation, current limits and terminal information.
Connector A — black, 32 way
PinFunction in rev 11 sourceA1Wideband lambda B 4B1Wideband lambda B 3C1Wideband lambda B heaterD1PWM low-side driver 7E1PWM low-side driver 8F1Fuel injector driver 5G1Bridge driver A−H1Ignition coil driver 4 (O4)A2Wideband lambda B 2B2Wideband lambda B 1C2LIN busD2MAP inputE2Timing input 2F2Fuel injector driver 6 (O26)G2Bridge driver A+H2Ignition coil driver 3 (O3)A3Knock input B+B3Knock input B−C3Timing input 1D3Analogue ground 4E35 V sensor supply 3F3Fuel injector driver 7G3Analogue input 20H3Ignition coil driver 5A4Active throttle feedback 2B4Active throttle feedback 1C4Analogue ground 2D4Coolant temperature inputE4Air inlet temperature inputF4Fuel injector driver 8G4Power returnH4Ignition coil driver 6
GEMS EM112: An eight-cylinder engine-management system with dual wideband lambda, eight coil drivers, eight programmable peak-and-hold injector drivers, three CAN buses and 256 MB internal logging. Manufacturer source.
Hardware and control
GEMS lists 20 analogue inputs, two differential analogue inputs, twelve timing inputs, two knock inputs and a 112-position Molex connector. It supports electronic throttle, variable cam timing and gearshift control, subject to ECU configuration. GEMS model information.
GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.
Connector and pinout
The EM112 technical specification, 103715 rev 11 includes model-specific connector and pinout drawings. Establish connector view, hardware revision and current limits in that document. The EM112 datasheet's connector C ignition driver names and software codes are internally inconsistent at some positions. Do not resolve them by assumption; obtain a confirmed drawing for the actual build from GEMS before connecting ignition.
Source discrepancies: Rev 11 labels connector A H1 and connector C H1 both as ignition coil driver 4, and assigns repeated software codes to other coil and injector outputs. These values are reproduced as printed, not reconciled; ask GEMS for the confirmed drawing for the unit before wiring. The original diagram includes orientation, current limits and terminal information.
GEMS EM112: An eight-cylinder engine-management system with dual wideband lambda, eight coil drivers, eight programmable peak-and-hold injector drivers, three CAN buses and 256 MB internal logging. Manufacturer source.
Hardware and control
GEMS lists 20 analogue inputs, two differential analogue inputs, twelve timing inputs, two knock inputs and a 112-position Molex connector. It supports electronic throttle, variable cam timing and gearshift control, subject to ECU configuration. GEMS model information.
GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.
Connector and pinout
The EM112 technical specification, 103715 rev 11 includes model-specific connector and pinout drawings. Establish connector view, hardware revision and current limits in that document. The EM112 datasheet's connector C ignition driver names and software codes are internally inconsistent at some positions. Do not resolve them by assumption; obtain a confirmed drawing for the actual build from GEMS before connecting ignition.
Source discrepancies: Rev 11 labels connector A H1 and connector C H1 both as ignition coil driver 4, and assigns repeated software codes to other coil and injector outputs. These values are reproduced as printed, not reconciled; ask GEMS for the confirmed drawing for the unit before wiring. The original diagram includes orientation, current limits and terminal information.