Page organisation in this revision
- Page type
- Technical article
- Subject
- Speeduino & standalone tuning
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 3 to revision 3
Removed text is struck through; added text is highlighted.
Ignition setup begins with a correctly interpreted engine position signal and a verified relationship between commanded and actual spark timing. Speeduino and MegaSquirt are separate ECU families: use the instructions for the installed hardware, firmware and trigger pattern.
Identify the hardware
Record crank and cam sensor types, trigger wheel or distributor pattern, coil and igniter type, firing order and ECU board revision. A variable-reluctance sensor and a Hall sensor do not necessarily use the same input circuit. Confirm the exact input conditioning, pull-up, polarity, shielding and earthing requirements in the relevant hardware manual. Never assume a connector pinout from a different board or revision.
Where the trigger or the high-tension distribution is still in a distributor, its centrifugal and vacuum advance must be locked and the rotor phased for the timing range the map will command. Without that, the trigger moves with rpm or the spark crossfires at one end of the range. The procedure is on Distributors with ECU-controlled timing: locking advance and rotor phasing.
Establish synchronisation
Choose the decoder and trigger edge specified for the actual engine and firmware. Configure the trigger pattern, missing teeth and cam input only as applicable to that installation.Check for a steady and plausible cranking RPM and review the available trigger or composite log. Lost synchronisation, noise or implausible readings must be resolved before tuning.Verify that the selected ignition output mode, firing order and coil-driver arrangement match the hardware. An incorrect output polarity or dwell setting can damage coils or ignition modules; use the coil and ECU documentation.
Verify timing with a light
Find and verify the engine's timing reference and top-dead-centre mark. Use the firmware's fixed-timing procedure and a suitable timing light to compare commanded timing with the crankshaft mark. Adjust the relevant trigger reference according to the matching manual, recheck over the specified operating range, then return the ECU to normal table control. The setting is specific to the engine, trigger and firmware; no universal trigger angle should be copied.
Calibrate the spark table
The spark table normally relates advance to engine speed and load. Corrections and operating modes can alter the actual command. Begin with a suitable validated starting calibration and verify the displayed timing, fuel quality, temperatures and sensor behaviour. Tune under controlled load with a capable operator and appropriate knock monitoring. Audible knock alone is not a reliable indicator that every operating point is safe. Avoid copying advance or dwell values between different engines or coils.
Common symptoms
No cranking RPM: investigate power, grounds, sensor wiring, conditioning and decoder selection.RPM present but sync lost: inspect the trigger log, sensor gap, signal quality, edge and wheel configuration.Timing mark disagrees: check the reference mark, cylinder, fixed-timing mode, trigger offset and any active corrections.Misfire or hot coils: stop and check output polarity, dwell, coil compatibility, wiring and firing order before further running.
Sources and further reading
Speeduino trigger setupSpeeduino hardware requirementsMS3 setup, hardware and TunerStudio manualsDIYAutoTune startup and timing checksCrankshaft and camshaft position sensors
For equipment and compatibility when checking ignition timing, see automotive timing lights.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Standalone ECU ignition and trigger setup
Ignition setup begins with a correctly interpreted engine position signal and a verified relationship between commanded and actual spark timing. Speeduino and MegaSquirt are separate ECU families: use the instructions for the installed hardware, firmware and trigger pattern.
Identify the hardware
Record crank and cam sensor types, trigger wheel or distributor pattern, coil and igniter type, firing order and ECU board revision. A variable-reluctance sensor and a Hall sensor do not necessarily use the same input circuit. Confirm the exact input conditioning, pull-up, polarity, shielding and earthing requirements in the relevant hardware manual. Never assume a connector pinout from a different board or revision.
Where the trigger or the high-tension distribution is still in a distributor, its centrifugal and vacuum advance must be locked and the rotor phased for the timing range the map will command. Without that, the trigger moves with rpm or the spark crossfires at one end of the range. The procedure is on Distributors with ECU-controlled timing: locking advance and rotor phasing.
Establish synchronisation
- Choose the decoder and trigger edge specified for the actual engine and firmware. Configure the trigger pattern, missing teeth and cam input only as applicable to that installation.
- Check for a steady and plausible cranking RPM and review the available trigger or composite log. Lost synchronisation, noise or implausible readings must be resolved before tuning.
- Verify that the selected ignition output mode, firing order and coil-driver arrangement match the hardware. An incorrect output polarity or dwell setting can damage coils or ignition modules; use the coil and ECU documentation.
Verify timing with a light
Find and verify the engine's timing reference and top-dead-centre mark. Use the firmware's fixed-timing procedure and a suitable timing light to compare commanded timing with the crankshaft mark. Adjust the relevant trigger reference according to the matching manual, recheck over the specified operating range, then return the ECU to normal table control. The setting is specific to the engine, trigger and firmware; no universal trigger angle should be copied.
Calibrate the spark table
The spark table normally relates advance to engine speed and load. Corrections and operating modes can alter the actual command. Begin with a suitable validated starting calibration and verify the displayed timing, fuel quality, temperatures and sensor behaviour. Tune under controlled load with a capable operator and appropriate knock monitoring. Audible knock alone is not a reliable indicator that every operating point is safe. Avoid copying advance or dwell values between different engines or coils.
Common symptoms
- No cranking RPM: investigate power, grounds, sensor wiring, conditioning and decoder selection.
- RPM present but sync lost: inspect the trigger log, sensor gap, signal quality, edge and wheel configuration.
- Timing mark disagrees: check the reference mark, cylinder, fixed-timing mode, trigger offset and any active corrections.
- Misfire or hot coils: stop and check output polarity, dwell, coil compatibility, wiring and firing order before further running.
Sources and further reading
For equipment and compatibility when checking ignition timing, see automotive timing lights.
Revision 3: Standalone ECU ignition and trigger setup
Ignition setup begins with a correctly interpreted engine position signal and a verified relationship between commanded and actual spark timing. Speeduino and MegaSquirt are separate ECU families: use the instructions for the installed hardware, firmware and trigger pattern.
Identify the hardware
Record crank and cam sensor types, trigger wheel or distributor pattern, coil and igniter type, firing order and ECU board revision. A variable-reluctance sensor and a Hall sensor do not necessarily use the same input circuit. Confirm the exact input conditioning, pull-up, polarity, shielding and earthing requirements in the relevant hardware manual. Never assume a connector pinout from a different board or revision.
Where the trigger or the high-tension distribution is still in a distributor, its centrifugal and vacuum advance must be locked and the rotor phased for the timing range the map will command. Without that, the trigger moves with rpm or the spark crossfires at one end of the range. The procedure is on Distributors with ECU-controlled timing: locking advance and rotor phasing.
Establish synchronisation
- Choose the decoder and trigger edge specified for the actual engine and firmware. Configure the trigger pattern, missing teeth and cam input only as applicable to that installation.
- Check for a steady and plausible cranking RPM and review the available trigger or composite log. Lost synchronisation, noise or implausible readings must be resolved before tuning.
- Verify that the selected ignition output mode, firing order and coil-driver arrangement match the hardware. An incorrect output polarity or dwell setting can damage coils or ignition modules; use the coil and ECU documentation.
Verify timing with a light
Find and verify the engine's timing reference and top-dead-centre mark. Use the firmware's fixed-timing procedure and a suitable timing light to compare commanded timing with the crankshaft mark. Adjust the relevant trigger reference according to the matching manual, recheck over the specified operating range, then return the ECU to normal table control. The setting is specific to the engine, trigger and firmware; no universal trigger angle should be copied.
Calibrate the spark table
The spark table normally relates advance to engine speed and load. Corrections and operating modes can alter the actual command. Begin with a suitable validated starting calibration and verify the displayed timing, fuel quality, temperatures and sensor behaviour. Tune under controlled load with a capable operator and appropriate knock monitoring. Audible knock alone is not a reliable indicator that every operating point is safe. Avoid copying advance or dwell values between different engines or coils.
Common symptoms
- No cranking RPM: investigate power, grounds, sensor wiring, conditioning and decoder selection.
- RPM present but sync lost: inspect the trigger log, sensor gap, signal quality, edge and wheel configuration.
- Timing mark disagrees: check the reference mark, cylinder, fixed-timing mode, trigger offset and any active corrections.
- Misfire or hot coils: stop and check output polarity, dwell, coil compatibility, wiring and firing order before further running.
Sources and further reading
For equipment and compatibility when checking ignition timing, see automotive timing lights.