Tuning Wiki

A timing light is a stroboscope used to observe the relationship between an ignition event and crankshaft timing marks. It flashes in response to a trigger, making the moving mark appear stationary against a fixed pointer or scale. Timing lights are useful on distributor engines and for checking some programmable ECU installations when the engine has reliable timing marks and a suitable pickup connection.

How timing lights work

Many automotive lights use an inductive pickup around a spark-plug high-tension (HT) lead and a 12 V supply for the strobe. A basic light flashes at the detected event; the technician reads the crank mark against the engine's scale. A dial-back or digital-advance light delays the flash by a selected amount so a suitable reference mark can be aligned, with the selected angle shown on the tool. Additional functions on some models include engine speed, dwell or voltage, sometimes requiring separate connections.

The marks indicate crankshaft angle, usually in degrees before or after top dead centre (BTDC or ATDC). Confirm the correct cylinder, pointer, rotation, scale and true top-dead-centre reference: a slipped harmonic damper or incorrect pointer can make an otherwise stable reading wrong. The timing light does not directly measure combustion pressure or prove that ignition timing is safe for the engine.

Diagnostic uses

  • Base timing: check and, where the manufacturer provides an adjustment, set initial ignition timing under the specified speed, temperature and control-system conditions. Many factory ECU-controlled systems have no routine distributor adjustment.
  • Mechanical and vacuum advance: on a suitable distributor, observe how timing changes with engine speed or a specified vacuum input. A hand vacuum pump and gauge can be used where the vehicle procedure calls for it. A timing change is evidence for further checks, not proof of one failed part. Innova timing-light manual.
  • Programmable ECU synchronisation: where instructed by the ECU manufacturer, compare a suitable fixed commanded ignition angle with the crank mark and correct the trigger/TDC offset so commanded and observed timing agree. Disable timing lock after the check. This calibrates the reference; it is not a substitute for tuning the ignition map. Haltech: trigger and TDC offset.
  • Intermittent trigger indications: an irregular or missing flash can suggest a pickup or ignition-event issue, but it does not prove spark quality under cylinder pressure. Check the pickup, leads and the ignition system with the appropriate test equipment.

Compatibility and interpretation

A pickup designed for an HT lead may not clamp directly onto a coil-on-plug system. Use only a pickup or test adapter and connection method approved for the specific tool and ignition system. Check supply voltage and polarity, including older 6 V or positive-earth vehicles; many lights require 12 V negative earth. A diesel does not provide the usual spark-plug trigger: certain older mechanical-injection tests use a dedicated compatible diesel converter and procedure, not a standard petrol timing-light connection. Sealey TL95 diesel converter.

Wasted-spark, two-stroke and multi-spark systems can produce a different number of pulses per revolution or multiple sparks per event. The tool's RPM and advance calculations may be wrong even if it flashes. Select the correct supported mode and validate against the ignition and timing-light manufacturers' instructions. Innova states that its 5568a does not support multi-spark/MSD systems; Holley notes that dial-back lights can misread MSD multiple-spark ignition and recommends a non-adjustable light for troubleshooting. Innova 5568a; Holley MSD troubleshooting.

With a dial-back light, follow the exact tool and engine procedure: zero the dial when reading a graduated crank scale unless the procedure specifies otherwise, and do not add the dialled angle to a scale reading without understanding the reference. For some electronic systems Innova instructs users to set the advance display to zero and read the engine marks. Use a verified fixed-flash light and correct marks if compatibility is uncertain. Innova manual; Haltech: timing-light types.

Practical checks and safety

  1. Identify the vehicle, ignition system, required timing marks and service procedure. Inspect the pickup and leads and confirm the light's supply and ignition compatibility.
  2. With the engine stopped, connect the instrument as instructed and route leads clear of belts, fans, hot exhaust and high-voltage components. Prepare the specified test conditions and any required ECU service or timing-lock mode.
  3. Observe the mark at the specified operating condition. Compare actual timing with the applicable specification or commanded fixed angle. Do not assume that a flash proves the timing mark or damper is accurate.
  4. Make an adjustment only where the vehicle or ECU procedure specifies it, recheck, restore disconnected controls and remove any timing lock. Switch off before disconnecting equipment and account for all tools.

Keep hands, clothing and leads clear of moving parts and hot surfaces; ignition systems produce hazardous high voltage. Secure the vehicle, ventilate the area and follow the manufacturer’s instructions. Adjusting ignition timing can affect knock, emissions and engine durability; use the correct calibration and operating conditions. See ignition tuning and standalone ECU ignition and trigger setup.

Timing-light directory

Numbers identify the documented light or accessory, not a guarantee of compatibility with every engine. Specifications, ignition support and availability vary by version and market.

  • Innova 3551a / 3555a: 3551a is an inductive light and 3555a adds a 0–60° dial-back control. The manual distinguishes their controls; verify compatible ignition and power systems. Innova 3551/3555 manual.
  • Innova 3568a / 5568a: digital advance and tachometer lights; the 5568a adds dwell and voltage functions. Innova lists 5596 as a replacement inductive pickup/lead set for the 5568. Innova excludes multi-spark/MSD operation for the 5568a. 5568a; 3568a; 5596 listing.
  • Snap-on EETL500: digital tachometer, advance meter and timing light; the dealer listing specifies 0–180° advance and a 10–16 V DC supply. Snap-on dealer listing.
  • OTC 3363 / 3365 / 3367: 3363 is an inductive base-timing light, 3365 adds an advance knob and 3367 has digital RPM and advance functions. OTC lists detachable leads and xenon flashes; check replacement parts and system support. OTC timing-light brochure.
  • Gunson G4113 Timestrobe: 12 V inductive xenon timing light. Gunson lists replacement flash tube 77009 and different maximum flash/RPM limits for four-stroke, two-stroke and wasted-spark use. Gunson G4113 information.
  • Gunson G4123 Supastrobe: professional 12 V digital light with advance, RPM, dwell and voltage functions. Gunson lists replacement leads as G4123P; compatibility must be verified for the specific ignition. Gunson G4123 information.
  • Sealey TL93.V2: digital 12 V timing light with advance, tachometer, dwell and voltage modes; Sealey documents a two-stroke/distributorless setting. Sealey TL93.V2 manual.
  • MSD Timing Pro 8992: inductive light with detachable lead assembly; Holley lists replacement cable 89921. Its stated ignition compatibility and the engine-specific test procedure should be checked together. Holley MSD 8992.

Older and discontinued models

  • Snap-on MT2261AP: earlier digital tachometer/advance/timing light; a Honda dealer equipment listing marks it discontinued and superseded by EETL500. Verify accessories and specifications for each model separately. MT2261AP listing.
  • Bosch FIX 7527 / FIX 7529: Bosch documents the inductive FIX 7527 and the digital RPM/advance FIX 7529; Bosch marks the 7529 discontinued. Bosch brochure; FIX 7529 listing.
  • MSD 8990 / 8991: MSD's 2015 catalogue identifies the 8990 as the earlier light superseded by 8992. The separate 8991 is a self-powered inductive light using six AAA batteries according to its instructions. MSD historical catalogue; 8991 instructions.

For used lights, inspect the case, pickup cores, insulation and supply leads, and verify replacement lead, lamp and ignition compatibility. A correct-looking flash is only useful when the pickup, timing reference and operating conditions are valid.

See also on-board and off-board vehicle diagnostics.

See also: Automotive spark and ignition testers for spark-checking methods, diagnostic limitations and tool examples.