Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Vehicles
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Gilbern

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

The Gilbern Invader was the last production model from Gilbern of Llantwit Fardre. It was built from 1969 until the company closed in 1974. It developed the Genie into a stiffer, better-equipped four-seat GT, powered by the Ford 3.0-litre Essex V6. There were three marks of coupé and, from 1971, an estate. About 603 to 606 Invaders were made, the largest total of any Gilbern model. Mk I and Mk II cars were sold as kits or fully built. The Mk III was sold factory-built only.

1971 Gilbern Invader Mk II at Capesthorne Hall, 2013. Photo: SG2012, Wikimedia Commons, CC BY 2.0.

Versions

VersionIntroducedMain changesBuilt (one count) Mk I coupéJuly 1969Reworked Genie with a stronger chassis, larger brakes and MGC-derived front suspension. Electric windows and a walnut dashboard were standard.78 Mk II coupé1970 or October 1971 (sources disagree)Stiffer front chassis triangulation, engine set further back, reclining seats212 Mk II estateDeliveries from March 1971Estate body on the Mk II chassis; £150 more than the coupé104 Mk III coupéSeptember 1972Wider, lower body; track 4 in wider; wheel-arch extensions; smaller grille; indicators below the bumper. Ford Cortina Mk III front suspension and Capri 3000GT engine. Factory-built only.212

The split above totals 606 and comes from one detailed secondary source. The more widely repeated total is 603. Estimates for the estate range from 68 to 108. The Gilbern Owners Club's count is 104, and that figure is the best supported. The figure of 68, still repeated in some references, appears to count only part of estate production.

The Mk II's launch date is unresolved. A reference that cites Autocar of 21 October 1971 places it at the October 1971 London Motor Show. Another account places it at the 1970 show. Estate deliveries began in March 1971 on the Mk II chassis, which fits the earlier date better.

Engine and transmission

Engine: 2,994 cc Ford Essex V6 as used in the Zodiac Mk IV, with a single Weber carburettor on Mk I and Mk II cars. The Mk III used the higher-output Capri 3000GT version. Power: published figures vary with the rating standard used. A secondary source gives 141 bhp at 4,750 rpm and 181 lb ft at 3,000 rpm. A 1971 road test quotes 124 bhp for the standard engine. Tuning: the 1971 Motor Sport test car had a Piper-tuned engine rated at 148 bhp. Transmission: Zodiac-derived four-speed manual with overdrive, or a three-speed automatic. Amgueddfa Cymru – National Museum Wales holds a Mk III automatic.

See Ford Capri and Ford Cortina for the Mk III donor cars.

Dashboard of a 1971 Invader Mk II, New Canaan, Connecticut, 2023. Photo: Mr.choppers, Wikimedia Commons, CC BY-SA 3.0; resized.

Chassis, suspension and brakes

All Invaders use a tubular steel chassis with a glass-fibre body bonded to it. The Genie's frame had suffered cracked tubes, so the Mk II gained extra triangulation at the front. A late-1971 road-test car had the following:

Rear suspension: live axle on coil springs, located by twin trailing arms and a Panhard rod, with Spax adjustable dampers. Brakes: Girling 11½ in front discs and rear drums, with servo assistance. Wheelbase: 7 ft 9 in.

Mk I and Mk II cars use MGC-derived front suspension and an MGC-type rear axle. The Mk III changed to a Ford Cortina Mk III front subframe and steering rack, with a wider Ford rear axle located by trailing links and a Panhard rod.

Gilbern Invader estate, first registered August 1971. Photo: Charles01, Wikimedia Commons, CC BY-SA 3.0; resized.

Performance and prices

SourceCarPriceFigures Motor Sport, December 1971Invader with Piper-tuned 148 bhp engineKit £1,767; built and tax-paid £2,236Over 120 mph; 0–100 mph 24.8 s; 22–23 mpg Autocar, 14 September 1972 (via a secondary reference)Mk III at launch£2,693—

One secondary source gives the Mk III price as £2,493, but the figure cited from Autocar is better supported. At either price the Mk III competed with established saloons such as the Jaguar XJ6 2.8, which hurt sales as the kit-car tax advantage disappeared. In May 2022 Hagerty UK valued a 1971 Invader at £6,800 in condition 4 and £15,900 in condition 1.

Gilbern Invader Mk III, showing the wider body, wheel-arch extensions and smaller grille, at Capesthorne Hall, 2014. Photo: SG2012, Wikimedia Commons, CC BY 2.0; resized.

Prototypes and survivors

A four-door Invader prototype was built after a suggestion that the car could serve as a police vehicle. It did not reach production. Amgueddfa Cymru – National Museum Wales holds a green Invader Mk II and a purple Mk III automatic in its collection at Nantgarw. The Gilbern Owners Club has saved the Mk III body moulds.

Specialists and parts

The engine, gearbox and Mk III running gear are Ford parts, and Mk I and Mk II suspension is largely MG. The body, glass and much of the trim are specific to Gilbern. Chassis condition is the main concern in restoration.

Gilbern Owners Club (UK). Its spares department holds an extensive Invader range, sells to members only, owns the Mk III moulds and windscreen moulds, and keeps the car register. gilbern.co.uk. Philip Ivimey, the club archivist, is credited in sale listings with Invader Mk III chassis restoration, including work in 2006 at the Ivimey & Boniface garage. These credits come from third-party listings only, and no trading website has been found. Chris Smith Gilbern Garage, High Street Garage, Lutterworth, Leicestershire. Carried out a documented chassis-up restoration of a 1971 Invader Mk II estate, begun in 2008. Its current trading status could not be confirmed. Towcester Classic Cars, Towcester, Northamptonshire. Its website has a project page describing an Invader chassis and suspension rebuild. The page could not be loaded directly, and the firm's current status was not confirmed. towcesterclassiccars.co.uk. Sporting Classic Marques, Bancffosfelen, Llanelli. A glass-fibre and classic restoration business described in the classic-car press as a Gilbern specialist. sportingclassicmarques.co.uk. Mev Spares (UK, online). Gilbern Invader and Genie parts category, including Essex V6 core-plug sets. mevspares.co.uk. Vintage Tyres (UK). Lists 165R15 as the standard Invader (1969–74) tyre and 185/70R15 as an option. vintagetyres.com.

The Gilbern make page has the full list of specialists, insurers and books.

Not established

Whether the Mk II was introduced at the 1970 or the 1971 London Motor Show. The Mk III's standard wheel and tyre size. One account mentions 13 in Ford wheels, but the tyre-supplier listing gives a 15 in size for the Invader range. Kerb weights from a period road test. Whether a Mk IV or long-wheelbase Invader prototype was built. Both are reported only in sources that could not be checked.

Sources

The 1972 Gilbern Invader, Ben Branch, Silodrome (page dated 19 November 2026; production split, Mk III details). Accessed 19 November 2026. Road impressions: Gilbern Invader, Motor Sport, December 1971. Accessed 19 November 2026. Gilbern, English Wikipedia (cites Autocar of 14 August 1969, 21 October 1971 and 14 September 1972). Accessed 19 November 2026. Welsh rarebit: Gilbern Invader Estate hits the market, Jon Burgess, Hagerty UK, 12 May 2022. Accessed 19 November 2026. The Gilbern – too good to be a 'one-off', Amgueddfa Cymru – National Museum Wales, 30 July 2019. Accessed 19 November 2026. Buyer's brief: Gilbern Invader 1969–1973, Practical Classics, 6 November 2024 (the club's windscreen moulds). Accessed 19 November 2026. Spares, Gilbern Owners Club. The site's security certificate could not be verified, so the content was read from search-engine copies. Accessed 19 November 2026. Specialist evidence: Car & Classic auction 1974 Gilbern Invader Mk3; PistonHeads forum thread; Mev Spares core-plug set; Vintage Tyres Invader fitment. Accessed 19 November 2026. Photographs from Wikimedia Commons, credited in each caption. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Gilbern Invader: Mk I, Mk II, Mk III and estate

The Gilbern Invader was the last production model from Gilbern of Llantwit Fardre. It was built from 1969 until the company closed in 1974. It developed the Genie into a stiffer, better-equipped four-seat GT, powered by the Ford 3.0-litre Essex V6. There were three marks of coupé and, from 1971, an estate. About 603 to 606 Invaders were made, the largest total of any Gilbern model. Mk I and Mk II cars were sold as kits or fully built. The Mk III was sold factory-built only.

A red 1971 Gilbern Invader Mk II coupé with a black vinyl roof.
1971 Gilbern Invader Mk II at Capesthorne Hall, 2013. Photo: SG2012, Wikimedia Commons, CC BY 2.0.

Versions

VersionIntroducedMain changesBuilt (one count)
Mk I coupéJuly 1969Reworked Genie with a stronger chassis, larger brakes and MGC-derived front suspension. Electric windows and a walnut dashboard were standard.78
Mk II coupé1970 or October 1971 (sources disagree)Stiffer front chassis triangulation, engine set further back, reclining seats212
Mk II estateDeliveries from March 1971Estate body on the Mk II chassis; £150 more than the coupé104
Mk III coupéSeptember 1972Wider, lower body; track 4 in wider; wheel-arch extensions; smaller grille; indicators below the bumper. Ford Cortina Mk III front suspension and Capri 3000GT engine. Factory-built only.212

The split above totals 606 and comes from one detailed secondary source. The more widely repeated total is 603. Estimates for the estate range from 68 to 108. The Gilbern Owners Club's count is 104, and that figure is the best supported. The figure of 68, still repeated in some references, appears to count only part of estate production.

The Mk II's launch date is unresolved. A reference that cites Autocar of 21 October 1971 places it at the October 1971 London Motor Show. Another account places it at the 1970 show. Estate deliveries began in March 1971 on the Mk II chassis, which fits the earlier date better.

Engine and transmission

  • Engine: 2,994 cc Ford Essex V6 as used in the Zodiac Mk IV, with a single Weber carburettor on Mk I and Mk II cars. The Mk III used the higher-output Capri 3000GT version.
  • Power: published figures vary with the rating standard used. A secondary source gives 141 bhp at 4,750 rpm and 181 lb ft at 3,000 rpm. A 1971 road test quotes 124 bhp for the standard engine.
  • Tuning: the 1971 Motor Sport test car had a Piper-tuned engine rated at 148 bhp.
  • Transmission: Zodiac-derived four-speed manual with overdrive, or a three-speed automatic. Amgueddfa Cymru – National Museum Wales holds a Mk III automatic.

See Ford Capri and Ford Cortina for the Mk III donor cars.

Interior of a 1971 Gilbern Invader Mk II showing the wood-rim steering wheel, instrument panel and gear lever.
Dashboard of a 1971 Invader Mk II, New Canaan, Connecticut, 2023. Photo: Mr.choppers, Wikimedia Commons, CC BY-SA 3.0; resized.

Chassis, suspension and brakes

All Invaders use a tubular steel chassis with a glass-fibre body bonded to it. The Genie's frame had suffered cracked tubes, so the Mk II gained extra triangulation at the front. A late-1971 road-test car had the following:

  • Rear suspension: live axle on coil springs, located by twin trailing arms and a Panhard rod, with Spax adjustable dampers.
  • Brakes: Girling 11½ in front discs and rear drums, with servo assistance.
  • Wheelbase: 7 ft 9 in.

Mk I and Mk II cars use MGC-derived front suspension and an MGC-type rear axle. The Mk III changed to a Ford Cortina Mk III front subframe and steering rack, with a wider Ford rear axle located by trailing links and a Panhard rod.

A white 1971 Gilbern Invader estate with a black roof, rear three-quarter view.
Gilbern Invader estate, first registered August 1971. Photo: Charles01, Wikimedia Commons, CC BY-SA 3.0; resized.

Performance and prices

SourceCarPriceFigures
Motor Sport, December 1971Invader with Piper-tuned 148 bhp engineKit £1,767; built and tax-paid £2,236Over 120 mph; 0–100 mph 24.8 s; 22–23 mpg
Autocar, 14 September 1972 (via a secondary reference)Mk III at launch£2,693—

One secondary source gives the Mk III price as £2,493, but the figure cited from Autocar is better supported. At either price the Mk III competed with established saloons such as the Jaguar XJ6 2.8, which hurt sales as the kit-car tax advantage disappeared. In May 2022 Hagerty UK valued a 1971 Invader at £6,800 in condition 4 and £15,900 in condition 1.

A blue Gilbern Invader Mk III with widened wheel arches and a red dragon badge on the grille.
Gilbern Invader Mk III, showing the wider body, wheel-arch extensions and smaller grille, at Capesthorne Hall, 2014. Photo: SG2012, Wikimedia Commons, CC BY 2.0; resized.

Prototypes and survivors

A four-door Invader prototype was built after a suggestion that the car could serve as a police vehicle. It did not reach production. Amgueddfa Cymru – National Museum Wales holds a green Invader Mk II and a purple Mk III automatic in its collection at Nantgarw. The Gilbern Owners Club has saved the Mk III body moulds.

Specialists and parts

The engine, gearbox and Mk III running gear are Ford parts, and Mk I and Mk II suspension is largely MG. The body, glass and much of the trim are specific to Gilbern. Chassis condition is the main concern in restoration.

  • Gilbern Owners Club (UK). Its spares department holds an extensive Invader range, sells to members only, owns the Mk III moulds and windscreen moulds, and keeps the car register. gilbern.co.uk.
  • Philip Ivimey, the club archivist, is credited in sale listings with Invader Mk III chassis restoration, including work in 2006 at the Ivimey & Boniface garage. These credits come from third-party listings only, and no trading website has been found.
  • Chris Smith Gilbern Garage, High Street Garage, Lutterworth, Leicestershire. Carried out a documented chassis-up restoration of a 1971 Invader Mk II estate, begun in 2008. Its current trading status could not be confirmed.
  • Towcester Classic Cars, Towcester, Northamptonshire. Its website has a project page describing an Invader chassis and suspension rebuild. The page could not be loaded directly, and the firm's current status was not confirmed. towcesterclassiccars.co.uk.
  • Sporting Classic Marques, Bancffosfelen, Llanelli. A glass-fibre and classic restoration business described in the classic-car press as a Gilbern specialist. sportingclassicmarques.co.uk.
  • Mev Spares (UK, online). Gilbern Invader and Genie parts category, including Essex V6 core-plug sets. mevspares.co.uk.
  • Vintage Tyres (UK). Lists 165R15 as the standard Invader (1969–74) tyre and 185/70R15 as an option. vintagetyres.com.

The Gilbern make page has the full list of specialists, insurers and books.

Not established

  • Whether the Mk II was introduced at the 1970 or the 1971 London Motor Show.
  • The Mk III's standard wheel and tyre size. One account mentions 13 in Ford wheels, but the tyre-supplier listing gives a 15 in size for the Invader range.
  • Kerb weights from a period road test.
  • Whether a Mk IV or long-wheelbase Invader prototype was built. Both are reported only in sources that could not be checked.

Sources

Revision 1: Gilbern Invader: Mk I, Mk II, Mk III and estate

The Gilbern Invader was the last production model from Gilbern of Llantwit Fardre. It was built from 1969 until the company closed in 1974. It developed the Genie into a stiffer, better-equipped four-seat GT, powered by the Ford 3.0-litre Essex V6. There were three marks of coupé and, from 1971, an estate. About 603 to 606 Invaders were made, the largest total of any Gilbern model. Mk I and Mk II cars were sold as kits or fully built. The Mk III was sold factory-built only.

A red 1971 Gilbern Invader Mk II coupé with a black vinyl roof.
1971 Gilbern Invader Mk II at Capesthorne Hall, 2013. Photo: SG2012, Wikimedia Commons, CC BY 2.0.

Versions

VersionIntroducedMain changesBuilt (one count)
Mk I coupéJuly 1969Reworked Genie with a stronger chassis, larger brakes and MGC-derived front suspension. Electric windows and a walnut dashboard were standard.78
Mk II coupé1970 or October 1971 (sources disagree)Stiffer front chassis triangulation, engine set further back, reclining seats212
Mk II estateDeliveries from March 1971Estate body on the Mk II chassis; £150 more than the coupé104
Mk III coupéSeptember 1972Wider, lower body; track 4 in wider; wheel-arch extensions; smaller grille; indicators below the bumper. Ford Cortina Mk III front suspension and Capri 3000GT engine. Factory-built only.212

The split above totals 606 and comes from one detailed secondary source. The more widely repeated total is 603. Estimates for the estate range from 68 to 108. The Gilbern Owners Club's count is 104, and that figure is the best supported. The figure of 68, still repeated in some references, appears to count only part of estate production.

The Mk II's launch date is unresolved. A reference that cites Autocar of 21 October 1971 places it at the October 1971 London Motor Show. Another account places it at the 1970 show. Estate deliveries began in March 1971 on the Mk II chassis, which fits the earlier date better.

Engine and transmission

  • Engine: 2,994 cc Ford Essex V6 as used in the Zodiac Mk IV, with a single Weber carburettor on Mk I and Mk II cars. The Mk III used the higher-output Capri 3000GT version.
  • Power: published figures vary with the rating standard used. A secondary source gives 141 bhp at 4,750 rpm and 181 lb ft at 3,000 rpm. A 1971 road test quotes 124 bhp for the standard engine.
  • Tuning: the 1971 Motor Sport test car had a Piper-tuned engine rated at 148 bhp.
  • Transmission: Zodiac-derived four-speed manual with overdrive, or a three-speed automatic. Amgueddfa Cymru – National Museum Wales holds a Mk III automatic.

See Ford Capri and Ford Cortina for the Mk III donor cars.

Interior of a 1971 Gilbern Invader Mk II showing the wood-rim steering wheel, instrument panel and gear lever.
Dashboard of a 1971 Invader Mk II, New Canaan, Connecticut, 2023. Photo: Mr.choppers, Wikimedia Commons, CC BY-SA 3.0; resized.

Chassis, suspension and brakes

All Invaders use a tubular steel chassis with a glass-fibre body bonded to it. The Genie's frame had suffered cracked tubes, so the Mk II gained extra triangulation at the front. A late-1971 road-test car had the following:

  • Rear suspension: live axle on coil springs, located by twin trailing arms and a Panhard rod, with Spax adjustable dampers.
  • Brakes: Girling 11½ in front discs and rear drums, with servo assistance.
  • Wheelbase: 7 ft 9 in.

Mk I and Mk II cars use MGC-derived front suspension and an MGC-type rear axle. The Mk III changed to a Ford Cortina Mk III front subframe and steering rack, with a wider Ford rear axle located by trailing links and a Panhard rod.

A white 1971 Gilbern Invader estate with a black roof, rear three-quarter view.
Gilbern Invader estate, first registered August 1971. Photo: Charles01, Wikimedia Commons, CC BY-SA 3.0; resized.

Performance and prices

SourceCarPriceFigures
Motor Sport, December 1971Invader with Piper-tuned 148 bhp engineKit £1,767; built and tax-paid £2,236Over 120 mph; 0–100 mph 24.8 s; 22–23 mpg
Autocar, 14 September 1972 (via a secondary reference)Mk III at launch£2,693—

One secondary source gives the Mk III price as £2,493, but the figure cited from Autocar is better supported. At either price the Mk III competed with established saloons such as the Jaguar XJ6 2.8, which hurt sales as the kit-car tax advantage disappeared. In May 2022 Hagerty UK valued a 1971 Invader at £6,800 in condition 4 and £15,900 in condition 1.

A blue Gilbern Invader Mk III with widened wheel arches and a red dragon badge on the grille.
Gilbern Invader Mk III, showing the wider body, wheel-arch extensions and smaller grille, at Capesthorne Hall, 2014. Photo: SG2012, Wikimedia Commons, CC BY 2.0; resized.

Prototypes and survivors

A four-door Invader prototype was built after a suggestion that the car could serve as a police vehicle. It did not reach production. Amgueddfa Cymru – National Museum Wales holds a green Invader Mk II and a purple Mk III automatic in its collection at Nantgarw. The Gilbern Owners Club has saved the Mk III body moulds.

Specialists and parts

The engine, gearbox and Mk III running gear are Ford parts, and Mk I and Mk II suspension is largely MG. The body, glass and much of the trim are specific to Gilbern. Chassis condition is the main concern in restoration.

  • Gilbern Owners Club (UK). Its spares department holds an extensive Invader range, sells to members only, owns the Mk III moulds and windscreen moulds, and keeps the car register. gilbern.co.uk.
  • Philip Ivimey, the club archivist, is credited in sale listings with Invader Mk III chassis restoration, including work in 2006 at the Ivimey & Boniface garage. These credits come from third-party listings only, and no trading website has been found.
  • Chris Smith Gilbern Garage, High Street Garage, Lutterworth, Leicestershire. Carried out a documented chassis-up restoration of a 1971 Invader Mk II estate, begun in 2008. Its current trading status could not be confirmed.
  • Towcester Classic Cars, Towcester, Northamptonshire. Its website has a project page describing an Invader chassis and suspension rebuild. The page could not be loaded directly, and the firm's current status was not confirmed. towcesterclassiccars.co.uk.
  • Sporting Classic Marques, Bancffosfelen, Llanelli. A glass-fibre and classic restoration business described in the classic-car press as a Gilbern specialist. sportingclassicmarques.co.uk.
  • Mev Spares (UK, online). Gilbern Invader and Genie parts category, including Essex V6 core-plug sets. mevspares.co.uk.
  • Vintage Tyres (UK). Lists 165R15 as the standard Invader (1969–74) tyre and 185/70R15 as an option. vintagetyres.com.

The Gilbern make page has the full list of specialists, insurers and books.

Not established

  • Whether the Mk II was introduced at the 1970 or the 1971 London Motor Show.
  • The Mk III's standard wheel and tyre size. One account mentions 13 in Ford wheels, but the tyre-supplier listing gives a 15 in size for the Invader range.
  • Kerb weights from a period road test.
  • Whether a Mk IV or long-wheelbase Invader prototype was built. Both are reported only in sources that could not be checked.

Sources