Connector pinout
The Electromotive TECs has one sealed 23-pin AMP connector (blue) for all inputs and outputs and a separate sealed two-way Delphi main power connector (MP630). The manufacturer manual (sections 9.1 and 9.2) gives the function, wire colour, gauge and destination for every pin and shows the 23-pin face from the wire side: pins 1 to 8 on the top row, 9 to 15 on the offset middle row and 16 to 23 on the bottom row, with the latch above the top row. All 25 pins are listed here as manufacturer documentation.
Power is supplied through the two-way connector: pin A is switched battery +12 V (red, 12 TXL) and pin B is ground (black, 10 TXL). On the 23-pin connector, injector outputs are on pins 23 (injector 1), 6 (injector 2), 4 (injector or GPO 3) and 1 (injector or GPO 4); ignition coil drivers A and B are on pins 9 and 16 with the coil shield on pin 2. Crank sensor positive is pin 11 and crank negative with shield is pin 10; cam sensor is pin 12. Sensor ground is pin 18 and the +5 V reference pin 19; manifold pressure, throttle position, coolant temperature, manifold temperature, knock and EGO are on pins 20, 21, 13, 14, 17 and 22. Fuel pump relay is pin 3, tach output pin 15, and general-purpose I/O on pins 5, 7 and 8 (pin 8 also serves as the speed input).
The manual does not show the face of the power connector, so the A/B positions in the diagram are schematic. Confirm the connector, harness and configuration on the actual unit before wiring.
Sources
- Electromotive TECs Manual (version 1.2 document; wiring section printed as version 1.0a), Electromotive, Inc.; sections 9.1 pinout information and 9.2 connector pin locations. Manufacturer documentation. Accessed 19 November 2026.
Connector pinout
Electromotive TECs (up to four-cylinder engines). One sealed 23-pin AMP input/output connector (blue) and a sealed two-way Delphi main power connector (MP630), from the TECs manual sections 9.1 and 9.2; manufacturer documentation. The 23-pin face is drawn as the manual shows it, from the wire side. The power connector face is not shown in the manual, so its A/B positions are schematic. Notes give the manual's wire colour, gauge and destination.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
Blue 23-pin AMP connector
View: Wire side of connector, as drawn in the manufacturer manual
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Injector or GPO 4 Cavity: Populated |
Confirmed TECs manual s9.1 |
Yel/Blue, 18 TXL, to Load | |
| Coil Shield Cavity: Populated |
Confirmed TECs manual s9.1 |
Shield, 18 TXL, to Ignition Coils | |
| Fuel Pump Cavity: Populated |
Confirmed TECs manual s9.1 |
Lt. Green, 18 TXL, to Relay | |
| Injector or GPO 3 Cavity: Populated |
Confirmed TECs manual s9.1 |
Yel/Grn, 18 TXL, to Load | |
| GPIO1 Cavity: Populated |
Confirmed TECs manual s9.1 |
Wht/Blk, 18 TXL, to Load or Input | |
| Injector 2 Cavity: Populated |
Confirmed TECs manual s9.1 |
Yel/Red, 18 TXL, to Load | |
| GPIO2 Cavity: Populated |
Confirmed TECs manual s9.1 |
Wht/Red, 18 TXL, to Load or Input | |
| GPO5/Speed Cavity: Populated |
Confirmed TECs manual s9.1 |
Wht/Grn, 18 TXL, to Load or Input | |
| Coil A Cavity: Populated |
Confirmed TECs manual s9.1 |
Black, 16 TSP, to Ignition Coils | |
| Crank Sensor - & Shield Cavity: Populated |
Confirmed TECs manual s9.1 |
Blk&Shld, 22 TSP, to Sensor | |
| Crank Sensor + Cavity: Populated |
Confirmed TECs manual s9.1 |
Red, 22 TSP, to Sensor | |
| CAM Sensor Cavity: Populated |
Confirmed TECs manual s9.1 |
Tan, 18 TXL, to Sensor | |
| Coolant Temp Cavity: Populated |
Confirmed TECs manual s9.1 |
Gray, 18 TXL, to Sensor | |
| Manifold Temp Cavity: Populated |
Confirmed TECs manual s9.1 |
White, 18 TXL, to Sensor | |
| Tach Out Cavity: Populated |
Confirmed TECs manual s9.1 |
Brown, 18 TXL, to Tachometer | |
| Coil B Cavity: Populated |
Confirmed TECs manual s9.1 |
Red, 16 TSP, to Ignition Coils | |
| Knock Cavity: Populated |
Confirmed TECs manual s9.1 |
Orange, 18 TXL, to Sensor | |
| Sensor Gnd Cavity: Populated |
Confirmed TECs manual s9.1 |
Blk/Wht, 18 TXL, to Various Common | |
| +5 Volts Cavity: Populated |
Confirmed TECs manual s9.1 |
Gry/Red, 18 TXL, to Various +5V | |
| Manifold Pressure Cavity: Populated |
Confirmed TECs manual s9.1 |
D. Green, 18 TXL, to Sensor | |
| Throttle Position Cavity: Populated |
Confirmed TECs manual s9.1 |
D. Blue, 18 TXL, to Sensor | |
| EGO + Cavity: Populated |
Confirmed TECs manual s9.1 |
Purple, 18 TXL, to Sensor | |
| Injector 1 Cavity: Populated |
Confirmed TECs manual s9.1 |
Yel/Blk, 18 TXL, to Load |
Two-way main power connector (MP630)
View: Schematic; face layout not shown in the source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Switched Battery 12V Cavity: Populated |
Confirmed TECs manual s9.1 |
Red, 12 TXL | |
| Ground Cavity: Populated |
Confirmed TECs manual s9.1 |
Black, 10 TXL |