Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Connector pinout

The Electromotive TECs has one sealed 23-pin AMP connector (blue) for all inputs and outputs and a separate sealed two-way Delphi main power connector (MP630). The manufacturer manual (sections 9.1 and 9.2) gives the function, wire colour, gauge and destination for every pin and shows the 23-pin face from the wire side: pins 1 to 8 on the top row, 9 to 15 on the offset middle row and 16 to 23 on the bottom row, with the latch above the top row. All 25 pins are listed here as manufacturer documentation.

Power is supplied through the two-way connector: pin A is switched battery +12 V (red, 12 TXL) and pin B is ground (black, 10 TXL). On the 23-pin connector, injector outputs are on pins 23 (injector 1), 6 (injector 2), 4 (injector or GPO 3) and 1 (injector or GPO 4); ignition coil drivers A and B are on pins 9 and 16 with the coil shield on pin 2. Crank sensor positive is pin 11 and crank negative with shield is pin 10; cam sensor is pin 12. Sensor ground is pin 18 and the +5 V reference pin 19; manifold pressure, throttle position, coolant temperature, manifold temperature, knock and EGO are on pins 20, 21, 13, 14, 17 and 22. Fuel pump relay is pin 3, tach output pin 15, and general-purpose I/O on pins 5, 7 and 8 (pin 8 also serves as the speed input).

The manual does not show the face of the power connector, so the A/B positions in the diagram are schematic. Confirm the connector, harness and configuration on the actual unit before wiring.

Electromotive TECs 23-pin connector face and two-way power connector
Electromotive TECs connectors; 23-pin face viewed from the wire side. Diagram redrawn by Tuning Wiki from the Electromotive TECs manual.

Sources

  • Electromotive TECs Manual (version 1.2 document; wiring section printed as version 1.0a), Electromotive, Inc.; sections 9.1 pinout information and 9.2 connector pin locations. Manufacturer documentation. Accessed 19 November 2026.

Connector pinout

Applicability

Electromotive TECs (up to four-cylinder engines). One sealed 23-pin AMP input/output connector (blue) and a sealed two-way Delphi main power connector (MP630), from the TECs manual sections 9.1 and 9.2; manufacturer documentation. The 23-pin face is drawn as the manual shows it, from the wire side. The power connector face is not shown in the manual, so its A/B positions are schematic. Notes give the manual's wire colour, gauge and destination.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

Blue 23-pin AMP connector

Redrawn connector face
View: Wire side of connector, as drawn in the manufacturer manual
Blue 23-pin AMP connector — Redrawn connector face. Wire side of connector, as drawn in the manufacturer manual

Select a pin in a photograph or the index to highlight it.

Blue 23-pin AMP connector — complete pin index
PinFunction / cavityConfidence / sourceNotes
Injector or GPO 4
Cavity: Populated
Confirmed

TECs manual s9.1

Yel/Blue, 18 TXL, to Load
Coil Shield
Cavity: Populated
Confirmed

TECs manual s9.1

Shield, 18 TXL, to Ignition Coils
Fuel Pump
Cavity: Populated
Confirmed

TECs manual s9.1

Lt. Green, 18 TXL, to Relay
Injector or GPO 3
Cavity: Populated
Confirmed

TECs manual s9.1

Yel/Grn, 18 TXL, to Load
GPIO1
Cavity: Populated
Confirmed

TECs manual s9.1

Wht/Blk, 18 TXL, to Load or Input
Injector 2
Cavity: Populated
Confirmed

TECs manual s9.1

Yel/Red, 18 TXL, to Load
GPIO2
Cavity: Populated
Confirmed

TECs manual s9.1

Wht/Red, 18 TXL, to Load or Input
GPO5/Speed
Cavity: Populated
Confirmed

TECs manual s9.1

Wht/Grn, 18 TXL, to Load or Input
Coil A
Cavity: Populated
Confirmed

TECs manual s9.1

Black, 16 TSP, to Ignition Coils
Crank Sensor - & Shield
Cavity: Populated
Confirmed

TECs manual s9.1

Blk&Shld, 22 TSP, to Sensor
Crank Sensor +
Cavity: Populated
Confirmed

TECs manual s9.1

Red, 22 TSP, to Sensor
CAM Sensor
Cavity: Populated
Confirmed

TECs manual s9.1

Tan, 18 TXL, to Sensor
Coolant Temp
Cavity: Populated
Confirmed

TECs manual s9.1

Gray, 18 TXL, to Sensor
Manifold Temp
Cavity: Populated
Confirmed

TECs manual s9.1

White, 18 TXL, to Sensor
Tach Out
Cavity: Populated
Confirmed

TECs manual s9.1

Brown, 18 TXL, to Tachometer
Coil B
Cavity: Populated
Confirmed

TECs manual s9.1

Red, 16 TSP, to Ignition Coils
Knock
Cavity: Populated
Confirmed

TECs manual s9.1

Orange, 18 TXL, to Sensor
Sensor Gnd
Cavity: Populated
Confirmed

TECs manual s9.1

Blk/Wht, 18 TXL, to Various Common
+5 Volts
Cavity: Populated
Confirmed

TECs manual s9.1

Gry/Red, 18 TXL, to Various +5V
Manifold Pressure
Cavity: Populated
Confirmed

TECs manual s9.1

D. Green, 18 TXL, to Sensor
Throttle Position
Cavity: Populated
Confirmed

TECs manual s9.1

D. Blue, 18 TXL, to Sensor
EGO +
Cavity: Populated
Confirmed

TECs manual s9.1

Purple, 18 TXL, to Sensor
Injector 1
Cavity: Populated
Confirmed

TECs manual s9.1

Yel/Blk, 18 TXL, to Load

Two-way main power connector (MP630)

Redrawn schematic
View: Schematic; face layout not shown in the source
Two-way main power connector (MP630) — Redrawn schematic. Schematic; face layout not shown in the source

Select a pin in a photograph or the index to highlight it.

Two-way main power connector (MP630) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Switched Battery 12V
Cavity: Populated
Confirmed

TECs manual s9.1

Red, 12 TXL
Ground
Cavity: Populated
Confirmed

TECs manual s9.1

Black, 10 TXL