Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Siemens MS
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

MSV70 is the Siemens/VDO controller for the first Valvetronic BMW six, the N52. The name is Siemens motor control with Valvetronic. This is the first time that system is used on a six-cylinder BMW. The engine and the rest of the petrol generations are on BMW petrol engine management. The N52 itself is on N51 and N52.

What it is responsible for

Ignition, injection, Valvetronic II, the lightened double VANOS, the mapped thermostat, the electric coolant pump, knock control, lambda control, tank ventilation, the request that allows the air-conditioning compressor to load the engine, the three-stage intake, the electric fuel pump, cruise control, the alternator, the heated crankcase ventilation, oil condition and oil level, the intelligent battery sensor, monitoring of its inputs and outputs, substitute values, and self-diagnosis. On the N52 it is the controller that meets the 2006 ULEV II diagnosis rules.

The module

The housing is aluminium. Two main connectors split into seven modules and 146 possible pins: modules of 26, 26 and 6 pins on one connector, and 6, 44, 12 and 26 pins on the other. The processor clock is 60 MHz, raised to cover the Valvetronic work. Ambient temperature and ambient pressure are read by sensors inside the unit. Battery, ignition and ground feed it in the usual way, through a main relay and the engine fuses. The workshop bus is PT-CAN.

Air

Load is set by intake-valve lift, not by the throttle plate alone. Valvetronic has its own relay, its own motor and an eccentric-shaft sensor, which is the feedback for the lift. The electronic throttle and the pedal module are still fitted. A hot-film meter measures the air. A differential-pressure sensor is part of the same air picture. Two actuators run the three-stage intake: idle and low speed, the middle of the range, and the top of the range. Crankcase ventilation is heated through its own relay. Secondary air has a pump, a relay and a meter of its own.

The rest of the inputs

Two knock sensors cover cylinders 1 to 3 and 4 to 6. Intake and exhaust camshaft sensors and a crankshaft sensor time the engine. Four oxygen-sensor paths are shown. Coolant temperature is read at the engine and at the radiator outlet. The pedal module, a sport button, the brake-light switch, the clutch switch, the access system and the stability controller are on the same overview. One air-flap magnet is marked as not fitted for the US cars. The electric coolant pump, the oil-condition sensor, the intelligent battery sensor and the alternator are outputs and sensed devices on that same diagram, not later additions.

The following N52KP uses MSV80. The jobs above are the MSV70 list, not a claim that every one of them is wired the same way on MSV80.

Processor

The AutoTuner compatibility list (tool compatibility listing, 28 October 2026) names the Freescale MPC563 as the microcontroller its tool addresses for MSV70, and AutoTuner's MSS70/MSV70 release article (19 June 2025) lists the same device. This is a tool vendor's statement; the BMW material above gives only the 60 MHz clock.

Engine applications

The Alientech KESS and K-TAG vehicle list associates MSV70 with the N52 six-cylinder in several BMW lines: the N52B25 (codes N52B25O0, N52B25O1, N52B25U0) and N52B30 (N52B30O0, N52B30U0) in the 3 Series, 5 Series, 6 Series, 7 Series and Z4. This is a tool compatibility listing, not a complete fitment record. Later N52 variants use MSV80.

Bench connection pinout

Bench-connection pins for this unit, with all 146 connector cavities drawn, are on Siemens MSV70 bench connection pinout.

Sources

AutoTuner compatibility list, export dated 28 October 2026. MCU column for MSV70 (MPC563). Accessed 19 November 2026.AutoTuner: Siemens MSS70 / MSV70, 19 June 2025. Accessed 19 November 2026.Alientech KESS and K-TAG vehicle list, undated PDF. MSV70 engine-code entries. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Siemens MSV70

MSV70 is the Siemens/VDO controller for the first Valvetronic BMW six, the N52. The name is Siemens motor control with Valvetronic. This is the first time that system is used on a six-cylinder BMW. The engine and the rest of the petrol generations are on BMW petrol engine management. The N52 itself is on N51 and N52.

What it is responsible for

Ignition, injection, Valvetronic II, the lightened double VANOS, the mapped thermostat, the electric coolant pump, knock control, lambda control, tank ventilation, the request that allows the air-conditioning compressor to load the engine, the three-stage intake, the electric fuel pump, cruise control, the alternator, the heated crankcase ventilation, oil condition and oil level, the intelligent battery sensor, monitoring of its inputs and outputs, substitute values, and self-diagnosis. On the N52 it is the controller that meets the 2006 ULEV II diagnosis rules.

The module

The housing is aluminium. Two main connectors split into seven modules and 146 possible pins: modules of 26, 26 and 6 pins on one connector, and 6, 44, 12 and 26 pins on the other. The processor clock is 60 MHz, raised to cover the Valvetronic work. Ambient temperature and ambient pressure are read by sensors inside the unit. Battery, ignition and ground feed it in the usual way, through a main relay and the engine fuses. The workshop bus is PT-CAN.

Air

Load is set by intake-valve lift, not by the throttle plate alone. Valvetronic has its own relay, its own motor and an eccentric-shaft sensor, which is the feedback for the lift. The electronic throttle and the pedal module are still fitted. A hot-film meter measures the air. A differential-pressure sensor is part of the same air picture. Two actuators run the three-stage intake: idle and low speed, the middle of the range, and the top of the range. Crankcase ventilation is heated through its own relay. Secondary air has a pump, a relay and a meter of its own.

The rest of the inputs

Two knock sensors cover cylinders 1 to 3 and 4 to 6. Intake and exhaust camshaft sensors and a crankshaft sensor time the engine. Four oxygen-sensor paths are shown. Coolant temperature is read at the engine and at the radiator outlet. The pedal module, a sport button, the brake-light switch, the clutch switch, the access system and the stability controller are on the same overview. One air-flap magnet is marked as not fitted for the US cars. The electric coolant pump, the oil-condition sensor, the intelligent battery sensor and the alternator are outputs and sensed devices on that same diagram, not later additions.

The following N52KP uses MSV80. The jobs above are the MSV70 list, not a claim that every one of them is wired the same way on MSV80.

Processor

The AutoTuner compatibility list (tool compatibility listing, 28 October 2026) names the Freescale MPC563 as the microcontroller its tool addresses for MSV70, and AutoTuner's MSS70/MSV70 release article (19 June 2025) lists the same device. This is a tool vendor's statement; the BMW material above gives only the 60 MHz clock.

Engine applications

The Alientech KESS and K-TAG vehicle list associates MSV70 with the N52 six-cylinder in several BMW lines: the N52B25 (codes N52B25O0, N52B25O1, N52B25U0) and N52B30 (N52B30O0, N52B30U0) in the 3 Series, 5 Series, 6 Series, 7 Series and Z4. This is a tool compatibility listing, not a complete fitment record. Later N52 variants use MSV80.

Bench connection pinout

Bench-connection pins for this unit, with all 146 connector cavities drawn, are on Siemens MSV70 bench connection pinout.

Sources

Revision 3: Siemens MSV70

MSV70 is the Siemens/VDO controller for the first Valvetronic BMW six, the N52. The name is Siemens motor control with Valvetronic. This is the first time that system is used on a six-cylinder BMW. The engine and the rest of the petrol generations are on BMW petrol engine management. The N52 itself is on N51 and N52.

What it is responsible for

Ignition, injection, Valvetronic II, the lightened double VANOS, the mapped thermostat, the electric coolant pump, knock control, lambda control, tank ventilation, the request that allows the air-conditioning compressor to load the engine, the three-stage intake, the electric fuel pump, cruise control, the alternator, the heated crankcase ventilation, oil condition and oil level, the intelligent battery sensor, monitoring of its inputs and outputs, substitute values, and self-diagnosis. On the N52 it is the controller that meets the 2006 ULEV II diagnosis rules.

The module

The housing is aluminium. Two main connectors split into seven modules and 146 possible pins: modules of 26, 26 and 6 pins on one connector, and 6, 44, 12 and 26 pins on the other. The processor clock is 60 MHz, raised to cover the Valvetronic work. Ambient temperature and ambient pressure are read by sensors inside the unit. Battery, ignition and ground feed it in the usual way, through a main relay and the engine fuses. The workshop bus is PT-CAN.

Air

Load is set by intake-valve lift, not by the throttle plate alone. Valvetronic has its own relay, its own motor and an eccentric-shaft sensor, which is the feedback for the lift. The electronic throttle and the pedal module are still fitted. A hot-film meter measures the air. A differential-pressure sensor is part of the same air picture. Two actuators run the three-stage intake: idle and low speed, the middle of the range, and the top of the range. Crankcase ventilation is heated through its own relay. Secondary air has a pump, a relay and a meter of its own.

The rest of the inputs

Two knock sensors cover cylinders 1 to 3 and 4 to 6. Intake and exhaust camshaft sensors and a crankshaft sensor time the engine. Four oxygen-sensor paths are shown. Coolant temperature is read at the engine and at the radiator outlet. The pedal module, a sport button, the brake-light switch, the clutch switch, the access system and the stability controller are on the same overview. One air-flap magnet is marked as not fitted for the US cars. The electric coolant pump, the oil-condition sensor, the intelligent battery sensor and the alternator are outputs and sensed devices on that same diagram, not later additions.

The following N52KP uses MSV80. The jobs above are the MSV70 list, not a claim that every one of them is wired the same way on MSV80.

Processor

The AutoTuner compatibility list (tool compatibility listing, 28 October 2026) names the Freescale MPC563 as the microcontroller its tool addresses for MSV70, and AutoTuner's MSS70/MSV70 release article (19 June 2025) lists the same device. This is a tool vendor's statement; the BMW material above gives only the 60 MHz clock.

Engine applications

The Alientech KESS and K-TAG vehicle list associates MSV70 with the N52 six-cylinder in several BMW lines: the N52B25 (codes N52B25O0, N52B25O1, N52B25U0) and N52B30 (N52B30O0, N52B30U0) in the 3 Series, 5 Series, 6 Series, 7 Series and Z4. This is a tool compatibility listing, not a complete fitment record. Later N52 variants use MSV80.

Bench connection pinout

Bench-connection pins for this unit, with all 146 connector cavities drawn, are on Siemens MSV70 bench connection pinout.

Sources