Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Autronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 5 to revision 5

Removed text is struck through; added text is highlighted.

Autronic sm2 manufacturer product image: Autronic; reproduced with permission.

Autronic SM2 is a standalone or earlier programmable engine-management system. SM2 lists eight selectable peak-and-hold injector drivers and four ignition outputs; standard ignition does not have dwell control. It has separate J1/J2/J3 connector arrangements and RS232 communication. Model-specific information.

Identification and features

Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.

Processor

Autronic's product page (manufacturer documentation) gives the SM2 microcontroller as a 16-bit Intel part running at 16 MHz. The exact part number is not stated in the sources checked.

Engine applications

The SM2 is a universal unit rather than a vehicle-specific ECU. Per Autronic it suits port-injected spark-ignition engines without drive-by-wire throttle or feedback-controlled variable camshafts, including high-output supercharged or turbocharged engines, two-rotor rotary and two-stroke engines, and engines with uneven firing intervals such as two- and four-cylinder V motorcycle engines and V6 car engines. Selectable cylinder counts are 1 to 8, 10, 12, 14 and 16, with full sequential injection up to eight cylinders and semi-sequential operation above that. Autronic positions it for high-performance motorsport. No specific engine codes are listed by the manufacturer.

Hardware per Autronic: supply 6.2 to 23 V, eight injector drivers selectable 4 A/1 A or 2 A/0.5 A peak/hold, four 1 A open-collector ignition outputs, four on-off outputs, two high-side PWM outputs, RS232 serial, and a 52-way AMP connector made up of 10-way, 18-way and 24-way plugs.

Wiring and pinout

Consult the Autronic SM2 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.

SM2 standard loom connector assignments

Autronic's SM2 basic wiring, traction-control option, drawing SM2WR105 revision 001 identifies positions 1 to 10 as J1, 11 to 28 as J2 and 29 to 52 as J3. The complete function table for all 52 positions follows and is also on the Autronic SM2 connector pinout page with redrawn pin-index diagrams. Positions 21, 23, 42 and 43 are not labelled in the drawing, which does not declare them safe to use. J4 is the serial connection: RxD, TxD and ground are shown but physical pin numbers are not supplied. Diagram redrawn by Tuning Wiki from the Autronic drawing.

Connector / positionFunction in drawingJ1 1ECU +12 V supplyJ1 2Injector 8 outputJ1 3ECU +12 V supplyJ1 4Injector 7 outputJ1 5Injector 6 outputJ1 6Injector 5 outputJ1 7Injector 4 outputJ1 8Injector 3 outputJ1 9ECU groundJ1 10ECU groundJ2 11Injector 2 outputJ2 12PWM 1 output (idle control)J2 13Injector 1 outputJ2 14PWM 2 output (boost control)J2 15Ignition switch inputJ2 16Solenoid 3 output (spare)J2 17Analogue outputJ2 18Coolant temperature inputJ2 19Coolant temperature groundJ2 20O2 / EGT inputJ2 21Not labelled in sourceJ2 22Exhaust back pressure inputJ2 23Not labelled in sourceJ2 24Intake air temperature inputJ2 25Intake air groundJ2 26Throttle position inputJ2 27Throttle position groundJ2 28Throttle position supplyJ3 29Auxiliary 2 analogue inputJ3 30Auxiliary 4 analogue inputJ3 31Auxiliary 1 analogue inputJ3 32Auxiliary 3 analogue inputJ3 33Auxiliary analogue input groundJ3 34Trigger supplyJ3 35Trigger groundJ3 36Reference trigger inputJ3 37Cylinder pulse trigger inputJ3 38Spare speed input (turbo tachometer)J3 39Vehicle speed inputJ3 40Switch 1 input (A/C request / traction control enable)J3 41Switch 2 input (boost curve select)J3 42Not labelled in sourceJ3 43Not labelled in sourceJ3 44Ignition output groundJ3 45Relay 1 output (fuel pump)J3 46Ignition 1 outputJ3 47Relay 2 output (A/C request)J3 48Ignition 2 outputJ3 49Relay 3 output (main cooling fan)J3 50Ignition 3 outputJ3 51Relay 4 output (auxiliary cooling fan)J3 52Ignition 4 output

Further information

Autronic SM2 model informationWiring, manuals or technical archiveAutronic manufacturer index

Sources

Autronic SM2 product page. Manufacturer. Accessed 19 November 2026.SM2 wiring drawing SM2WR105 revision 001. Manufacturer. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 5: Autronic SM2
Autronic sm2 ECU
Autronic sm2 manufacturer product image: Autronic; reproduced with permission.

Autronic SM2 is a standalone or earlier programmable engine-management system. SM2 lists eight selectable peak-and-hold injector drivers and four ignition outputs; standard ignition does not have dwell control. It has separate J1/J2/J3 connector arrangements and RS232 communication. Model-specific information.

Identification and features

Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.

Processor

Autronic's product page (manufacturer documentation) gives the SM2 microcontroller as a 16-bit Intel part running at 16 MHz. The exact part number is not stated in the sources checked.

Engine applications

The SM2 is a universal unit rather than a vehicle-specific ECU. Per Autronic it suits port-injected spark-ignition engines without drive-by-wire throttle or feedback-controlled variable camshafts, including high-output supercharged or turbocharged engines, two-rotor rotary and two-stroke engines, and engines with uneven firing intervals such as two- and four-cylinder V motorcycle engines and V6 car engines. Selectable cylinder counts are 1 to 8, 10, 12, 14 and 16, with full sequential injection up to eight cylinders and semi-sequential operation above that. Autronic positions it for high-performance motorsport. No specific engine codes are listed by the manufacturer.

Hardware per Autronic: supply 6.2 to 23 V, eight injector drivers selectable 4 A/1 A or 2 A/0.5 A peak/hold, four 1 A open-collector ignition outputs, four on-off outputs, two high-side PWM outputs, RS232 serial, and a 52-way AMP connector made up of 10-way, 18-way and 24-way plugs.

Wiring and pinout

Consult the Autronic SM2 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.

SM2 standard loom connector assignments

Autronic's SM2 basic wiring, traction-control option, drawing SM2WR105 revision 001 identifies positions 1 to 10 as J1, 11 to 28 as J2 and 29 to 52 as J3. The complete function table for all 52 positions follows and is also on the Autronic SM2 connector pinout page with redrawn pin-index diagrams. Positions 21, 23, 42 and 43 are not labelled in the drawing, which does not declare them safe to use. J4 is the serial connection: RxD, TxD and ground are shown but physical pin numbers are not supplied. Diagram redrawn by Tuning Wiki from the Autronic drawing.

Connector / positionFunction in drawing
J1 1ECU +12 V supply
J1 2Injector 8 output
J1 3ECU +12 V supply
J1 4Injector 7 output
J1 5Injector 6 output
J1 6Injector 5 output
J1 7Injector 4 output
J1 8Injector 3 output
J1 9ECU ground
J1 10ECU ground
J2 11Injector 2 output
J2 12PWM 1 output (idle control)
J2 13Injector 1 output
J2 14PWM 2 output (boost control)
J2 15Ignition switch input
J2 16Solenoid 3 output (spare)
J2 17Analogue output
J2 18Coolant temperature input
J2 19Coolant temperature ground
J2 20O2 / EGT input
J2 21Not labelled in source
J2 22Exhaust back pressure input
J2 23Not labelled in source
J2 24Intake air temperature input
J2 25Intake air ground
J2 26Throttle position input
J2 27Throttle position ground
J2 28Throttle position supply
J3 29Auxiliary 2 analogue input
J3 30Auxiliary 4 analogue input
J3 31Auxiliary 1 analogue input
J3 32Auxiliary 3 analogue input
J3 33Auxiliary analogue input ground
J3 34Trigger supply
J3 35Trigger ground
J3 36Reference trigger input
J3 37Cylinder pulse trigger input
J3 38Spare speed input (turbo tachometer)
J3 39Vehicle speed input
J3 40Switch 1 input (A/C request / traction control enable)
J3 41Switch 2 input (boost curve select)
J3 42Not labelled in source
J3 43Not labelled in source
J3 44Ignition output ground
J3 45Relay 1 output (fuel pump)
J3 46Ignition 1 output
J3 47Relay 2 output (A/C request)
J3 48Ignition 2 output
J3 49Relay 3 output (main cooling fan)
J3 50Ignition 3 output
J3 51Relay 4 output (auxiliary cooling fan)
J3 52Ignition 4 output

Further information

Sources

Revision 5: Autronic SM2
Autronic sm2 ECU
Autronic sm2 manufacturer product image: Autronic; reproduced with permission.

Autronic SM2 is a standalone or earlier programmable engine-management system. SM2 lists eight selectable peak-and-hold injector drivers and four ignition outputs; standard ignition does not have dwell control. It has separate J1/J2/J3 connector arrangements and RS232 communication. Model-specific information.

Identification and features

Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.

Processor

Autronic's product page (manufacturer documentation) gives the SM2 microcontroller as a 16-bit Intel part running at 16 MHz. The exact part number is not stated in the sources checked.

Engine applications

The SM2 is a universal unit rather than a vehicle-specific ECU. Per Autronic it suits port-injected spark-ignition engines without drive-by-wire throttle or feedback-controlled variable camshafts, including high-output supercharged or turbocharged engines, two-rotor rotary and two-stroke engines, and engines with uneven firing intervals such as two- and four-cylinder V motorcycle engines and V6 car engines. Selectable cylinder counts are 1 to 8, 10, 12, 14 and 16, with full sequential injection up to eight cylinders and semi-sequential operation above that. Autronic positions it for high-performance motorsport. No specific engine codes are listed by the manufacturer.

Hardware per Autronic: supply 6.2 to 23 V, eight injector drivers selectable 4 A/1 A or 2 A/0.5 A peak/hold, four 1 A open-collector ignition outputs, four on-off outputs, two high-side PWM outputs, RS232 serial, and a 52-way AMP connector made up of 10-way, 18-way and 24-way plugs.

Wiring and pinout

Consult the Autronic SM2 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.

SM2 standard loom connector assignments

Autronic's SM2 basic wiring, traction-control option, drawing SM2WR105 revision 001 identifies positions 1 to 10 as J1, 11 to 28 as J2 and 29 to 52 as J3. The complete function table for all 52 positions follows and is also on the Autronic SM2 connector pinout page with redrawn pin-index diagrams. Positions 21, 23, 42 and 43 are not labelled in the drawing, which does not declare them safe to use. J4 is the serial connection: RxD, TxD and ground are shown but physical pin numbers are not supplied. Diagram redrawn by Tuning Wiki from the Autronic drawing.

Connector / positionFunction in drawing
J1 1ECU +12 V supply
J1 2Injector 8 output
J1 3ECU +12 V supply
J1 4Injector 7 output
J1 5Injector 6 output
J1 6Injector 5 output
J1 7Injector 4 output
J1 8Injector 3 output
J1 9ECU ground
J1 10ECU ground
J2 11Injector 2 output
J2 12PWM 1 output (idle control)
J2 13Injector 1 output
J2 14PWM 2 output (boost control)
J2 15Ignition switch input
J2 16Solenoid 3 output (spare)
J2 17Analogue output
J2 18Coolant temperature input
J2 19Coolant temperature ground
J2 20O2 / EGT input
J2 21Not labelled in source
J2 22Exhaust back pressure input
J2 23Not labelled in source
J2 24Intake air temperature input
J2 25Intake air ground
J2 26Throttle position input
J2 27Throttle position ground
J2 28Throttle position supply
J3 29Auxiliary 2 analogue input
J3 30Auxiliary 4 analogue input
J3 31Auxiliary 1 analogue input
J3 32Auxiliary 3 analogue input
J3 33Auxiliary analogue input ground
J3 34Trigger supply
J3 35Trigger ground
J3 36Reference trigger input
J3 37Cylinder pulse trigger input
J3 38Spare speed input (turbo tachometer)
J3 39Vehicle speed input
J3 40Switch 1 input (A/C request / traction control enable)
J3 41Switch 2 input (boost curve select)
J3 42Not labelled in source
J3 43Not labelled in source
J3 44Ignition output ground
J3 45Relay 1 output (fuel pump)
J3 46Ignition 1 output
J3 47Relay 2 output (A/C request)
J3 48Ignition 2 output
J3 49Relay 3 output (main cooling fan)
J3 50Ignition 3 output
J3 51Relay 4 output (auxiliary cooling fan)
J3 52Ignition 4 output

Further information

Sources