Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Lucas GEMS
Applies to
Lucas GEMS
Tool groups
None
Manufacturers
Land Rover, Morgan

Connector pinout

The Lucas GEMS engine control module is fitted with three connectors: C509 (18-pin, black), C507 (36-pin, red) and C505 (36-pin, black). The Morgan Plus 8 GEMS operations and maintenance manual (version 4.70, 15 July 2005) tabulates all 90 pins for North American Plus 8 cars of 1998-2004 with the 4.6 litre V8. C509 carries the coil drivers, crankshaft sensor, main-relay and ignition feeds and ECM grounds. C507 carries sensor inputs, knock sensors, oxygen sensors, the diagnostic K and L lines and the immobiliser link. C505 carries the eight injectors, the idle-air stepper, purge, fuel-pump relay, malfunction lamp and tachometer-type outputs.

Evidence grade: secondary. The table comes from a community-compiled, vehicle-specific manual, not from Land Rover documentation, so all pin functions are marked suspected. Range Rover, Discovery and other GEMS installations use their own pin lists and the pin numbers must not be assumed to carry across. The diagrams are numbered pin indexes; the source gives neither the cavity layout nor the viewing orientation.

Pin index of Lucas GEMS connector C509, 18 pins
C509 pin index. Redrawn by Tuning Wiki from the Morgan Plus 8 GEMS manual.
Pin index of Lucas GEMS connector C507, 36 pins
C507 pin index.
Pin index of Lucas GEMS connector C505, 36 pins
C505 pin index.

See Lucas GEMS for the system overview.

Sources

  • Morgan Plus 8, 1998-2004, Operations and Maintenance, Engine Management System (GEMS version 4.70), 15 July 2005, GEMSbyPoole.pdf. ECM interfaces, connectors C509, C507 and C505. Accessed 19 November 2026.

Connector pinout

Applicability

Lucas GEMS ECM connectors C509, C507 and C505 as tabulated in the Morgan Plus 8 GEMS operations and maintenance manual (version 4.70, 15 July 2005) for North American 1998-2004 Plus 8 cars with the 4.6 litre V8. Community-compiled vehicle-specific manual; Range Rover and Discovery installations use their own pin lists and are not covered. Evidence: secondary.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

C509 (18-pin, black)

Redrawn pin index
View: Orientation not stated in source; pin numbers only
C509 (18-pin, black) — Redrawn pin index. Orientation not stated in source; pin numbers only

Select a pin in a photograph or the index to highlight it.

C509 (18-pin, black) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Coil driver - Cylinders 5 & 8
Cavity: Populated
Suspected Output; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Throttle Position Sensor
Cavity: Populated
Suspected Output; 5V supply
ECM to chassis ground
Cavity: Populated
Suspected Ground; 0V
No connection
Cavity: Unused
Suspected Not used
Main relay supply
Cavity: Populated
Suspected Input; 0 - 12V
Ignition sense
Cavity: Populated
Suspected Input; 0 - 12V
ECM to chassis ground
Cavity: Populated
Suspected Ground; 0V
ECM to chassis ground
Cavity: Populated
Suspected Ground; 0V
Crankshaft(CKP)sensor-ve
Cavity: Populated
Suspected Ground; 0V
Crankshaft (CKP) sensor +ve
Cavity: Populated
Suspected Analogue input; 18V (average) at 480Hz
Coil driver - Cylinders 2 & 3
Cavity: Populated
Suspected Output; 0 - 12V
Coil driver - Cylinders 1 & 6
Cavity: Populated
Suspected Output; 0 - 12V
Coil driver - Cylinders 4 & 7
Cavity: Populated
Suspected Output; 0 - 12V
ECM to chassis ground
Cavity: Populated
Suspected Ground; 0V
Main relay control
Cavity: Populated
Suspected Output; Switched to ground
No connection
Cavity: Unused
Suspected Not used

C507 (36-pin, red)

Redrawn pin index
View: Orientation not stated in source; pin numbers only
C507 (36-pin, red) — Redrawn pin index. Orientation not stated in source; pin numbers only

Select a pin in a photograph or the index to highlight it.

C507 (36-pin, red) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Rough road detected
Cavity: Populated
Suspected Input; 0 -12V
Camshaft position (CMP) sensor
Cavity: Populated
Suspected Input (2 pulses per engine revolution); 12V (average)
No connection
Cavity: Unused
Suspected Not used
Transfer box (Low range detected)
Cavity: Populated
Suspected Input; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Fuel level
Cavity: Populated
Suspected Input (out of range and validity check only); 0 - 12V
HO2S Bank B Upstream
Cavity: Populated
Suspected Input; 0V (Rich) - 5V (Lean)
No connection
Cavity: Unused
Suspected Not used
Knock sensor ground
Cavity: Populated
Suspected Ground; 0V
Knock sensor A
Cavity: Populated
Suspected Input; Voltage signal proportional to level of knock detected
Knock sensor B
Cavity: Populated
Suspected Input; Voltage signal proportional to level of knock detected
Air temperature sensor
Cavity: Populated
Suspected Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F)
Coolant temperature sensor
Cavity: Populated
Suspected Input; 4.7V at -30 C (-22 F) to 0.25V at 130 C (266 F); 2.0V at 40 C (104 F)
Throttle position sensor
Cavity: Populated
Suspected Input; 0 to 5V (0.6V at idle; 4.5V typical max.)
Mass air flow (MAF) Sensor
Cavity: Populated
Suspected Analogue input; 0 to 5V (1.4V at idle)
HO2S sensor Bank A downstream
Cavity: Populated
Suspected Input; 0V (Rich) - 5V (Lean)
Park/Neutral Switch
Cavity: Populated
Suspected Input; 0V (Park/Neutral) - 12V (Drive)
No connection
Cavity: Unused
Suspected Not used
Diagnostic L Line
Cavity: Populated
Suspected Bi-directional; Serial 0 - 12V
Heated front windshield
Cavity: Populated
Suspected Output; 0V or 12V
No connection
Cavity: Unused
Suspected Not used
Diagnostic K Line
Cavity: Populated
Suspected Bi-directional; Serial 0 - 12V
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Immobilization
Cavity: Populated
Suspected Input; Serial 0 - 12V (366 baud)
Vehicle speed
Cavity: Populated
Suspected Input; PWM 0 - 12V (8000 pulses / mile)
A/C request
Cavity: Populated
Suspected Output; 0V or 12V
Condenser cooling fan request
Cavity: Populated
Suspected Input; 0V or 12V
Fuel Pressure Sensor (from 97.5 MY)
Cavity: Populated
Suspected Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F)
Ignition Retard Request (EAT ECU)
Cavity: Populated
Suspected Input; 12V PWM
HO2S sensor
Cavity: Populated
Suspected Ground; 0V
HO2S sensor Bank B Downstream
Cavity: Populated
Suspected Input; 0V (Rich) - 5V (Lean)
HO2S sensor Bank A Upstream
Cavity: Populated
Suspected Input; 0V (Rich) - 5V (Lean)
Fuel temperature sensor
Cavity: Populated
Suspected Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F)
Sensor ground
Cavity: Populated
Suspected Ground; 0V

C505 (36-pin, black)

Redrawn pin index
View: Orientation not stated in source; pin numbers only
C505 (36-pin, black) — Redrawn pin index. Orientation not stated in source; pin numbers only

Select a pin in a photograph or the index to highlight it.

C505 (36-pin, black) — complete pin index
PinFunction / cavityConfidence / sourceNotes
A/C grant
Cavity: Populated
Suspected Output; 0V or 12V
Fuel used
Cavity: Populated
Suspected Output; Serial 0 - 12V (12000 pulses per liter)
Condenser cooling fan
Cavity: Populated
Suspected Output drive; Switch to ground
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Canister vent solenoid (from 97.5 MY)
Cavity: Populated
Suspected Output; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Injector - Cylinder 3
Cavity: Populated
Suspected Output; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
Injector- Cylinder 1
Cavity: Populated
Suspected Output; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
IACV-D Stepper motor
Cavity: Populated
Suspected Output; Stepped by sequentially changing voltage polarity
IACV-B Stepper motor
Cavity: Populated
Suspected Output; Stepped by sequentially changing voltage polarity
Injector - Cylinder 6
Cavity: Populated
Suspected Output; 0 - 12V
Injector - Cylinder 8
Cavity: Populated
Suspected Output; 0 - 12V
Purge valve
Cavity: Populated
Suspected Output; 0 - 12V (100 Hz)
No connection
Cavity: Unused
Suspected Not used
HO2S sensor Upstream - Heater supply
Cavity: Populated
Suspected Output; Heater resistance is 5.7 ohms
Malfunction Indicator Lamp (MIL)
Cavity: Populated
Suspected Output drive; Switch to ground
Engine speed output
Cavity: Populated
Suspected Output; 12V square wave (4 pulses per revolution)
Fuel pump relay
Cavity: Populated
Suspected Output drive; Switch to ground
No connection
Cavity: Unused
Suspected Not used
No connection
Cavity: Unused
Suspected Not used
Throttle position
Cavity: Populated
Suspected Analogue input; 0 - 5V (1.4V at idle)
HO2S sensor Upstream - Heater supply
Cavity: Populated
Suspected Output; Heater resistance is 5.7 ohms
Engine torque
Cavity: Populated
Suspected Output; 12V PWM
Injector - Cylinder 4
Cavity: Populated
Suspected Output; 0 - 12V
No connection
Cavity: Unused
Suspected Not used
Injector - Cylinder 7
Cavity: Populated
Suspected Output; 0 - 12V
Injector - Cylinder 5
Cavity: Populated
Suspected Output; 0 - 12V
IACV-C Stepper motor
Cavity: Populated
Suspected Output; Stepped by sequentially changing signal polarity
IACV-A Stepper motor
Cavity: Populated
Suspected Output; Stepped by sequentially changing signal polarity
Injector - Cylinder 2
Cavity: Populated
Suspected Output; 0 - 12V