Connector pinout
The Lucas GEMS engine control module is fitted with three connectors: C509 (18-pin, black), C507 (36-pin, red) and C505 (36-pin, black). The Morgan Plus 8 GEMS operations and maintenance manual (version 4.70, 15 July 2005) tabulates all 90 pins for North American Plus 8 cars of 1998-2004 with the 4.6 litre V8. C509 carries the coil drivers, crankshaft sensor, main-relay and ignition feeds and ECM grounds. C507 carries sensor inputs, knock sensors, oxygen sensors, the diagnostic K and L lines and the immobiliser link. C505 carries the eight injectors, the idle-air stepper, purge, fuel-pump relay, malfunction lamp and tachometer-type outputs.
Evidence grade: secondary. The table comes from a community-compiled, vehicle-specific manual, not from Land Rover documentation, so all pin functions are marked suspected. Range Rover, Discovery and other GEMS installations use their own pin lists and the pin numbers must not be assumed to carry across. The diagrams are numbered pin indexes; the source gives neither the cavity layout nor the viewing orientation.
See Lucas GEMS for the system overview.
Sources
- Morgan Plus 8, 1998-2004, Operations and Maintenance, Engine Management System (GEMS version 4.70), 15 July 2005, GEMSbyPoole.pdf. ECM interfaces, connectors C509, C507 and C505. Accessed 19 November 2026.
Connector pinout
Lucas GEMS ECM connectors C509, C507 and C505 as tabulated in the Morgan Plus 8 GEMS operations and maintenance manual (version 4.70, 15 July 2005) for North American 1998-2004 Plus 8 cars with the 4.6 litre V8. Community-compiled vehicle-specific manual; Range Rover and Discovery installations use their own pin lists and are not covered. Evidence: secondary.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
C509 (18-pin, black)
View: Orientation not stated in source; pin numbers only
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Coil driver - Cylinders 5 & 8 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Throttle Position Sensor Cavity: Populated |
Suspected | Output; 5V supply | |
| ECM to chassis ground Cavity: Populated |
Suspected | Ground; 0V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Main relay supply Cavity: Populated |
Suspected | Input; 0 - 12V | |
| Ignition sense Cavity: Populated |
Suspected | Input; 0 - 12V | |
| ECM to chassis ground Cavity: Populated |
Suspected | Ground; 0V | |
| ECM to chassis ground Cavity: Populated |
Suspected | Ground; 0V | |
| Crankshaft(CKP)sensor-ve Cavity: Populated |
Suspected | Ground; 0V | |
| Crankshaft (CKP) sensor +ve Cavity: Populated |
Suspected | Analogue input; 18V (average) at 480Hz | |
| Coil driver - Cylinders 2 & 3 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| Coil driver - Cylinders 1 & 6 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| Coil driver - Cylinders 4 & 7 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| ECM to chassis ground Cavity: Populated |
Suspected | Ground; 0V | |
| Main relay control Cavity: Populated |
Suspected | Output; Switched to ground | |
| No connection Cavity: Unused |
Suspected | Not used |
C507 (36-pin, red)
View: Orientation not stated in source; pin numbers only
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Rough road detected Cavity: Populated |
Suspected | Input; 0 -12V | |
| Camshaft position (CMP) sensor Cavity: Populated |
Suspected | Input (2 pulses per engine revolution); 12V (average) | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Transfer box (Low range detected) Cavity: Populated |
Suspected | Input; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Fuel level Cavity: Populated |
Suspected | Input (out of range and validity check only); 0 - 12V | |
| HO2S Bank B Upstream Cavity: Populated |
Suspected | Input; 0V (Rich) - 5V (Lean) | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Knock sensor ground Cavity: Populated |
Suspected | Ground; 0V | |
| Knock sensor A Cavity: Populated |
Suspected | Input; Voltage signal proportional to level of knock detected | |
| Knock sensor B Cavity: Populated |
Suspected | Input; Voltage signal proportional to level of knock detected | |
| Air temperature sensor Cavity: Populated |
Suspected | Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F) | |
| Coolant temperature sensor Cavity: Populated |
Suspected | Input; 4.7V at -30 C (-22 F) to 0.25V at 130 C (266 F); 2.0V at 40 C (104 F) | |
| Throttle position sensor Cavity: Populated |
Suspected | Input; 0 to 5V (0.6V at idle; 4.5V typical max.) | |
| Mass air flow (MAF) Sensor Cavity: Populated |
Suspected | Analogue input; 0 to 5V (1.4V at idle) | |
| HO2S sensor Bank A downstream Cavity: Populated |
Suspected | Input; 0V (Rich) - 5V (Lean) | |
| Park/Neutral Switch Cavity: Populated |
Suspected | Input; 0V (Park/Neutral) - 12V (Drive) | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Diagnostic L Line Cavity: Populated |
Suspected | Bi-directional; Serial 0 - 12V | |
| Heated front windshield Cavity: Populated |
Suspected | Output; 0V or 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Diagnostic K Line Cavity: Populated |
Suspected | Bi-directional; Serial 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Immobilization Cavity: Populated |
Suspected | Input; Serial 0 - 12V (366 baud) | |
| Vehicle speed Cavity: Populated |
Suspected | Input; PWM 0 - 12V (8000 pulses / mile) | |
| A/C request Cavity: Populated |
Suspected | Output; 0V or 12V | |
| Condenser cooling fan request Cavity: Populated |
Suspected | Input; 0V or 12V | |
| Fuel Pressure Sensor (from 97.5 MY) Cavity: Populated |
Suspected | Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F) | |
| Ignition Retard Request (EAT ECU) Cavity: Populated |
Suspected | Input; 12V PWM | |
| HO2S sensor Cavity: Populated |
Suspected | Ground; 0V | |
| HO2S sensor Bank B Downstream Cavity: Populated |
Suspected | Input; 0V (Rich) - 5V (Lean) | |
| HO2S sensor Bank A Upstream Cavity: Populated |
Suspected | Input; 0V (Rich) - 5V (Lean) | |
| Fuel temperature sensor Cavity: Populated |
Suspected | Input; 1 k-ohm to 1.3 k-ohm at 40 C (140 F) | |
| Sensor ground Cavity: Populated |
Suspected | Ground; 0V |
C505 (36-pin, black)
View: Orientation not stated in source; pin numbers only
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| A/C grant Cavity: Populated |
Suspected | Output; 0V or 12V | |
| Fuel used Cavity: Populated |
Suspected | Output; Serial 0 - 12V (12000 pulses per liter) | |
| Condenser cooling fan Cavity: Populated |
Suspected | Output drive; Switch to ground | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Canister vent solenoid (from 97.5 MY) Cavity: Populated |
Suspected | Output; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Injector - Cylinder 3 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Injector- Cylinder 1 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| IACV-D Stepper motor Cavity: Populated |
Suspected | Output; Stepped by sequentially changing voltage polarity | |
| IACV-B Stepper motor Cavity: Populated |
Suspected | Output; Stepped by sequentially changing voltage polarity | |
| Injector - Cylinder 6 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| Injector - Cylinder 8 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| Purge valve Cavity: Populated |
Suspected | Output; 0 - 12V (100 Hz) | |
| No connection Cavity: Unused |
Suspected | Not used | |
| HO2S sensor Upstream - Heater supply Cavity: Populated |
Suspected | Output; Heater resistance is 5.7 ohms | |
| Malfunction Indicator Lamp (MIL) Cavity: Populated |
Suspected | Output drive; Switch to ground | |
| Engine speed output Cavity: Populated |
Suspected | Output; 12V square wave (4 pulses per revolution) | |
| Fuel pump relay Cavity: Populated |
Suspected | Output drive; Switch to ground | |
| No connection Cavity: Unused |
Suspected | Not used | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Throttle position Cavity: Populated |
Suspected | Analogue input; 0 - 5V (1.4V at idle) | |
| HO2S sensor Upstream - Heater supply Cavity: Populated |
Suspected | Output; Heater resistance is 5.7 ohms | |
| Engine torque Cavity: Populated |
Suspected | Output; 12V PWM | |
| Injector - Cylinder 4 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| No connection Cavity: Unused |
Suspected | Not used | |
| Injector - Cylinder 7 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| Injector - Cylinder 5 Cavity: Populated |
Suspected | Output; 0 - 12V | |
| IACV-C Stepper motor Cavity: Populated |
Suspected | Output; Stepped by sequentially changing signal polarity | |
| IACV-A Stepper motor Cavity: Populated |
Suspected | Output; Stepped by sequentially changing signal polarity | |
| Injector - Cylinder 2 Cavity: Populated |
Suspected | Output; 0 - 12V |