Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Delphi diesel
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 7 to revision 7

Removed text is struck through; added text is highlighted.

DCM is the generation

In Delphi's September 2007 common-rail manual, DCM means diesel control module. The generation number is the hardware generation. DCU 1.1 and the DCM 1.1 on a label are the same series of names. The manual's table gives the path count, the electronics, the emissions standard and the applications as Delphi stated them then. A later car can carry a number from this table on a different engine. The label and the software still have to match.

Generation Paths Electronics Standard Applications named in the 2007 table 1.1 112, three connectors TRW, 16-bit Euro 3 Renault K9, Kia, Ford Lynx 1.2 112, three connectors TRW, 16-bit Euro 4 Renault K9 2.1 112, three connectors TRW, 32-bit Euro 3 PSA DV4 TED4 3.1 121, one connector Delco, 32-bit Euro 3 and Euro 4 Ford and SsangYong 3.2 154, two connectors Delco, 32-bit Euro 4 DaimlerChrysler OM646 3.3 124, two connectors Delco, 32-bit Tier 3 JCB 3.4 128, three connectors Delco, 32-bit Euro 4 and Euro 5 PSA DW10B and Renault K9 Euro 5 3.5 154, three connectors Delco, 32-bit Euro 5 PSA DW10C and DaimlerChrysler OM651, solenoid injectors 4.1 154, two connectors Delco, 32-bit Euro 5, piezo injector DaimlerChrysler OM651, piezo

TRW and Delco in that table are the electronics named for the generation. They do not move the controller into another manufacturer's wiki. Generation 1.2 is 16-bit. From 3.1 the table is 32-bit Delco. Generation 4.1 is the piezo OM651. Generation 3.5 is the solenoid OM651 and the PSA DW10C. A piezo file does not belong on the solenoid controller.

Where a later list disagrees

Mecaprog, a repairer, assigns the numbers differently for the cars it sees. DCM 1.2 is the Renault, Dacia and Nissan 1.5 dCi of 2004 to 2011, which agrees with the manual's Renault K9 row. DCM 3.4 in that list is the later 1.5 dCi, Euro 5 and Euro 6, and it does not mention the DW10B. DCM 3.5 in that list is the Peugeot and Citroën 1.4 and 1.6 HDi and the Ford 1.4 and 1.6 TDCi. The 2007 table puts the DV4 TED4 on generation 2.1 and the DW10C on generation 3.5. Those two accounts are not the same map. Use the 2007 table for what Delphi printed, and use the label on the controller for the car.

The same repairer puts DCM 6.2 and DCM 7.1 on the 1.5 and 1.6 BlueHDi and on the Ford 1.5 TDCi, and describes those two as locked against an ordinary diagnostic read. Tool support changes, and the exact suffix, vehicle and protocol matter; AutoTuner lists OBD access for some DCM6.2 configurations, so the repairer's statement should not be treated as a universal limitation. They are not in the 2007 table. Ford's 2016 Kuga specification says the 2.0 TDCi of 150 and 180 PS uses Delphi engine management and the 1.5 TDCi of 120 PS uses Bosch. That document does not give a DCM number, so the Kuga 2.0 is not assumed to be a 6.2.

Alientech's former coverage page listed "DCM3.5 - CRD2" for the Mercedes Sprinter and the Jeep Compass and Patriot, which is the OM651 side of generation 3.5, not the repairer's 1.6 HDi. That name is on Delphi CRD.

Microcontrollers by type

Delphi's 2007 table gives only the word length of the electronics. The microcontroller for each later type name is taken from the AutoTuner ECU compatibility list of 28 October 2026 (a tool compatibility listing, not a Delphi document). It records one microcontroller family per listed type; the same type name can cover more than one board revision, and AutoTuner itself lists three microcontrollers under DCM6.2AP.

Type name in the tool listMicrocontroller listed DCM1.2ST10F280 (STMicroelectronics 16-bit) DCM3.1MPC555 DCM3.2APMPC563 DCM3.4 and DCM3.4(+)SH7059; SH7058 or SH7059 for the (+) group DCM3.5 (and CRD2)MPC5566 DCM3.7SH72543 DCM3.7APSH72513 DCM6.1TC1797 DCM6.2A, 6.2C, 6.2V, 6.2AP-6DMPC5674F DCM6.2APMPC5674F, SPC5674 or SPC5673 DCM7.1A, DCM7.1BTC297 DCM7.1AP, DCM7.24TC277

The "DDCR" name used by tool makers for early 1.5 dCi units is listed with a C167 microcontroller; see DCM 1.1. These are tool-list statements. They show the processor families a tool must handle, not which generation of Delphi's own table a given board belongs to.

Family guides

DCM 1.1: first-generation Euro 3 controller and the Delphi DDCR tool name.DCM 1.2: Renault K9K diagnostic and injector coding examples.DCM 3.4: application and processor evidence.DCM3.7 and DCM3.7AP: road and off-highway examples.DCM6.1 and DCM6.2: suffixes, processor and vehicle examples.

Sources

Delphi France SAS, Common Rail Manual DDGX200(EN), issue 1, September 2007. The generation table, path counts, TRW and Delco, and the applications. Mirror: DDGX200. Accessed 2026-11-13. Mecaprog, Delphi DCM repair notes. Later assignments for 1.2, 3.4, 3.5, 6.2 and 7.1. Mecaprog DCM. Accessed 2026-11-13. Ford of Europe, Kuga technical specifications, October 2016. Delphi on the 2.0 TDCi 150 and 180, Bosch on the 1.5 TDCi, no generation number. Kuga specifications. Alientech, historical ECU version DCM3.5 - CRD2 listing: the previously consulted page is no longer available. A separate Alientech K-Suite 2.32 list: Jeep Compass and Jeep Patriot (PDF, 20 MB) show DCM3.5 - CRD2 examples; its rows do not establish every detail of the former listing. AutoTuner DCM6.2A: tool-specific OBD and boot coverage; accessed 17 November 2026. AutoTuner, ECU compatibility list (PDF export, 28 October 2026): microcontroller per Delphi type name. Tool compatibility listing. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 7: Delphi DCM

DCM is the generation

In Delphi's September 2007 common-rail manual, DCM means diesel control module. The generation number is the hardware generation. DCU 1.1 and the DCM 1.1 on a label are the same series of names. The manual's table gives the path count, the electronics, the emissions standard and the applications as Delphi stated them then. A later car can carry a number from this table on a different engine. The label and the software still have to match.

Generation Paths Electronics Standard Applications named in the 2007 table
1.1 112, three connectors TRW, 16-bit Euro 3 Renault K9, Kia, Ford Lynx
1.2 112, three connectors TRW, 16-bit Euro 4 Renault K9
2.1 112, three connectors TRW, 32-bit Euro 3 PSA DV4 TED4
3.1 121, one connector Delco, 32-bit Euro 3 and Euro 4 Ford and SsangYong
3.2 154, two connectors Delco, 32-bit Euro 4 DaimlerChrysler OM646
3.3 124, two connectors Delco, 32-bit Tier 3 JCB
3.4 128, three connectors Delco, 32-bit Euro 4 and Euro 5 PSA DW10B and Renault K9 Euro 5
3.5 154, three connectors Delco, 32-bit Euro 5 PSA DW10C and DaimlerChrysler OM651, solenoid injectors
4.1 154, two connectors Delco, 32-bit Euro 5, piezo injector DaimlerChrysler OM651, piezo

TRW and Delco in that table are the electronics named for the generation. They do not move the controller into another manufacturer's wiki. Generation 1.2 is 16-bit. From 3.1 the table is 32-bit Delco. Generation 4.1 is the piezo OM651. Generation 3.5 is the solenoid OM651 and the PSA DW10C. A piezo file does not belong on the solenoid controller.

Where a later list disagrees

Mecaprog, a repairer, assigns the numbers differently for the cars it sees. DCM 1.2 is the Renault, Dacia and Nissan 1.5 dCi of 2004 to 2011, which agrees with the manual's Renault K9 row. DCM 3.4 in that list is the later 1.5 dCi, Euro 5 and Euro 6, and it does not mention the DW10B. DCM 3.5 in that list is the Peugeot and Citroën 1.4 and 1.6 HDi and the Ford 1.4 and 1.6 TDCi. The 2007 table puts the DV4 TED4 on generation 2.1 and the DW10C on generation 3.5. Those two accounts are not the same map. Use the 2007 table for what Delphi printed, and use the label on the controller for the car.

The same repairer puts DCM 6.2 and DCM 7.1 on the 1.5 and 1.6 BlueHDi and on the Ford 1.5 TDCi, and describes those two as locked against an ordinary diagnostic read. Tool support changes, and the exact suffix, vehicle and protocol matter; AutoTuner lists OBD access for some DCM6.2 configurations, so the repairer's statement should not be treated as a universal limitation. They are not in the 2007 table. Ford's 2016 Kuga specification says the 2.0 TDCi of 150 and 180 PS uses Delphi engine management and the 1.5 TDCi of 120 PS uses Bosch. That document does not give a DCM number, so the Kuga 2.0 is not assumed to be a 6.2.

Alientech's former coverage page listed "DCM3.5 - CRD2" for the Mercedes Sprinter and the Jeep Compass and Patriot, which is the OM651 side of generation 3.5, not the repairer's 1.6 HDi. That name is on Delphi CRD.

Microcontrollers by type

Delphi's 2007 table gives only the word length of the electronics. The microcontroller for each later type name is taken from the AutoTuner ECU compatibility list of 28 October 2026 (a tool compatibility listing, not a Delphi document). It records one microcontroller family per listed type; the same type name can cover more than one board revision, and AutoTuner itself lists three microcontrollers under DCM6.2AP.

Type name in the tool listMicrocontroller listed
DCM1.2ST10F280 (STMicroelectronics 16-bit)
DCM3.1MPC555
DCM3.2APMPC563
DCM3.4 and DCM3.4(+)SH7059; SH7058 or SH7059 for the (+) group
DCM3.5 (and CRD2)MPC5566
DCM3.7SH72543
DCM3.7APSH72513
DCM6.1TC1797
DCM6.2A, 6.2C, 6.2V, 6.2AP-6DMPC5674F
DCM6.2APMPC5674F, SPC5674 or SPC5673
DCM7.1A, DCM7.1BTC297
DCM7.1AP, DCM7.24TC277

The "DDCR" name used by tool makers for early 1.5 dCi units is listed with a C167 microcontroller; see DCM 1.1. These are tool-list statements. They show the processor families a tool must handle, not which generation of Delphi's own table a given board belongs to.

Family guides

  • DCM 1.1: first-generation Euro 3 controller and the Delphi DDCR tool name.
  • DCM 1.2: Renault K9K diagnostic and injector coding examples.
  • DCM 3.4: application and processor evidence.
  • DCM3.7 and DCM3.7AP: road and off-highway examples.
  • DCM6.1 and DCM6.2: suffixes, processor and vehicle examples.

Sources

  • Delphi France SAS, Common Rail Manual DDGX200(EN), issue 1, September 2007. The generation table, path counts, TRW and Delco, and the applications. Mirror: DDGX200. Accessed 2026-11-13.
  • Mecaprog, Delphi DCM repair notes. Later assignments for 1.2, 3.4, 3.5, 6.2 and 7.1. Mecaprog DCM. Accessed 2026-11-13.
  • Ford of Europe, Kuga technical specifications, October 2016. Delphi on the 2.0 TDCi 150 and 180, Bosch on the 1.5 TDCi, no generation number. Kuga specifications.
  • Alientech, historical ECU version DCM3.5 - CRD2 listing: the previously consulted page is no longer available. A separate Alientech K-Suite 2.32 list: Jeep Compass and Jeep Patriot (PDF, 20 MB) show DCM3.5 - CRD2 examples; its rows do not establish every detail of the former listing.
  • AutoTuner DCM6.2A: tool-specific OBD and boot coverage; accessed 17 November 2026.
  • AutoTuner, ECU compatibility list (PDF export, 28 October 2026): microcontroller per Delphi type name. Tool compatibility listing. Accessed 19 November 2026.
Revision 7: Delphi DCM

DCM is the generation

In Delphi's September 2007 common-rail manual, DCM means diesel control module. The generation number is the hardware generation. DCU 1.1 and the DCM 1.1 on a label are the same series of names. The manual's table gives the path count, the electronics, the emissions standard and the applications as Delphi stated them then. A later car can carry a number from this table on a different engine. The label and the software still have to match.

Generation Paths Electronics Standard Applications named in the 2007 table
1.1 112, three connectors TRW, 16-bit Euro 3 Renault K9, Kia, Ford Lynx
1.2 112, three connectors TRW, 16-bit Euro 4 Renault K9
2.1 112, three connectors TRW, 32-bit Euro 3 PSA DV4 TED4
3.1 121, one connector Delco, 32-bit Euro 3 and Euro 4 Ford and SsangYong
3.2 154, two connectors Delco, 32-bit Euro 4 DaimlerChrysler OM646
3.3 124, two connectors Delco, 32-bit Tier 3 JCB
3.4 128, three connectors Delco, 32-bit Euro 4 and Euro 5 PSA DW10B and Renault K9 Euro 5
3.5 154, three connectors Delco, 32-bit Euro 5 PSA DW10C and DaimlerChrysler OM651, solenoid injectors
4.1 154, two connectors Delco, 32-bit Euro 5, piezo injector DaimlerChrysler OM651, piezo

TRW and Delco in that table are the electronics named for the generation. They do not move the controller into another manufacturer's wiki. Generation 1.2 is 16-bit. From 3.1 the table is 32-bit Delco. Generation 4.1 is the piezo OM651. Generation 3.5 is the solenoid OM651 and the PSA DW10C. A piezo file does not belong on the solenoid controller.

Where a later list disagrees

Mecaprog, a repairer, assigns the numbers differently for the cars it sees. DCM 1.2 is the Renault, Dacia and Nissan 1.5 dCi of 2004 to 2011, which agrees with the manual's Renault K9 row. DCM 3.4 in that list is the later 1.5 dCi, Euro 5 and Euro 6, and it does not mention the DW10B. DCM 3.5 in that list is the Peugeot and Citroën 1.4 and 1.6 HDi and the Ford 1.4 and 1.6 TDCi. The 2007 table puts the DV4 TED4 on generation 2.1 and the DW10C on generation 3.5. Those two accounts are not the same map. Use the 2007 table for what Delphi printed, and use the label on the controller for the car.

The same repairer puts DCM 6.2 and DCM 7.1 on the 1.5 and 1.6 BlueHDi and on the Ford 1.5 TDCi, and describes those two as locked against an ordinary diagnostic read. Tool support changes, and the exact suffix, vehicle and protocol matter; AutoTuner lists OBD access for some DCM6.2 configurations, so the repairer's statement should not be treated as a universal limitation. They are not in the 2007 table. Ford's 2016 Kuga specification says the 2.0 TDCi of 150 and 180 PS uses Delphi engine management and the 1.5 TDCi of 120 PS uses Bosch. That document does not give a DCM number, so the Kuga 2.0 is not assumed to be a 6.2.

Alientech's former coverage page listed "DCM3.5 - CRD2" for the Mercedes Sprinter and the Jeep Compass and Patriot, which is the OM651 side of generation 3.5, not the repairer's 1.6 HDi. That name is on Delphi CRD.

Microcontrollers by type

Delphi's 2007 table gives only the word length of the electronics. The microcontroller for each later type name is taken from the AutoTuner ECU compatibility list of 28 October 2026 (a tool compatibility listing, not a Delphi document). It records one microcontroller family per listed type; the same type name can cover more than one board revision, and AutoTuner itself lists three microcontrollers under DCM6.2AP.

Type name in the tool listMicrocontroller listed
DCM1.2ST10F280 (STMicroelectronics 16-bit)
DCM3.1MPC555
DCM3.2APMPC563
DCM3.4 and DCM3.4(+)SH7059; SH7058 or SH7059 for the (+) group
DCM3.5 (and CRD2)MPC5566
DCM3.7SH72543
DCM3.7APSH72513
DCM6.1TC1797
DCM6.2A, 6.2C, 6.2V, 6.2AP-6DMPC5674F
DCM6.2APMPC5674F, SPC5674 or SPC5673
DCM7.1A, DCM7.1BTC297
DCM7.1AP, DCM7.24TC277

The "DDCR" name used by tool makers for early 1.5 dCi units is listed with a C167 microcontroller; see DCM 1.1. These are tool-list statements. They show the processor families a tool must handle, not which generation of Delphi's own table a given board belongs to.

Family guides

  • DCM 1.1: first-generation Euro 3 controller and the Delphi DDCR tool name.
  • DCM 1.2: Renault K9K diagnostic and injector coding examples.
  • DCM 3.4: application and processor evidence.
  • DCM3.7 and DCM3.7AP: road and off-highway examples.
  • DCM6.1 and DCM6.2: suffixes, processor and vehicle examples.

Sources

  • Delphi France SAS, Common Rail Manual DDGX200(EN), issue 1, September 2007. The generation table, path counts, TRW and Delco, and the applications. Mirror: DDGX200. Accessed 2026-11-13.
  • Mecaprog, Delphi DCM repair notes. Later assignments for 1.2, 3.4, 3.5, 6.2 and 7.1. Mecaprog DCM. Accessed 2026-11-13.
  • Ford of Europe, Kuga technical specifications, October 2016. Delphi on the 2.0 TDCi 150 and 180, Bosch on the 1.5 TDCi, no generation number. Kuga specifications.
  • Alientech, historical ECU version DCM3.5 - CRD2 listing: the previously consulted page is no longer available. A separate Alientech K-Suite 2.32 list: Jeep Compass and Jeep Patriot (PDF, 20 MB) show DCM3.5 - CRD2 examples; its rows do not establish every detail of the former listing.
  • AutoTuner DCM6.2A: tool-specific OBD and boot coverage; accessed 17 November 2026.
  • AutoTuner, ECU compatibility list (PDF export, 28 October 2026): microcontroller per Delphi type name. Tool compatibility listing. Accessed 19 November 2026.