Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Altitude compensation is the set of corrections an engine ECU applies as ambient pressure falls. Air density drops by roughly a tenth for each 1,000 m climbed, so a naturally aspirated engine loses charge and power in about the same proportion, and any fuelling or boost strategy that assumes sea-level air becomes wrong.

A turbocharged engine can hold its absolute manifold pressure at altitude, but only by running the compressor at a higher pressure ratio and shaft speed. Factory calibrations therefore reduce boost, fuel or torque as ambient pressure falls, to keep the turbocharger inside its speed and temperature limits. A remap developed at sea level never exercises those corrections, which is the reason to leave them in place.

How air changes with altitude

The International Standard Atmosphere takes sea level as 15 °C, 101.325 kPa and 1.225 kg/m³, with temperature falling 6.5 °C per kilometre in the lower atmosphere. The values below are from the U.S. Standard Atmosphere 1976, which matches it at these heights.

AltitudeTemperaturePressureDensityDensity relative to sea level
0 m15.0 °C101.3 kPa1.225 kg/m³100%
1,000 m8.5 °C89.9 kPa1.112 kg/m³91%
2,000 m2.0 °C79.5 kPa1.007 kg/m³82%
3,000 m−4.5 °C70.1 kPa0.909 kg/m³74%
4,000 m−11.0 °C61.7 kPa0.819 kg/m³67%

A trade article using Garrett data gives about 3% power loss per 1,000 ft for a naturally aspirated engine, which agrees with the density column.

How the ECU knows ambient pressure

  • Dedicated sensor. Bosch describes an atmospheric-pressure sensor fitted inside the diesel ECU or elsewhere in the engine bay, measuring 60 to 115 kPa absolute. Its signal corrects the setpoints of closed loops such as EGR and boost pressure (manufacturer documentation).
  • Manifold sensor at key-on and wide-open throttle. With the engine stopped the MAP sensor sees ambient pressure. A 1986 Bendix patent stores that reading and then adjusts it while running, only at wide-open throttle and after allowing a fixed pressure drop across the throttle body. Haltech's standalone ECU manual takes the reading at power-up and warns that cranking early makes the sensor read manifold vacuum instead.
  • Modelled from airflow. A 2002 Ford patent estimates barometric pressure continuously, without a sensor, by comparing measured MAF or MAP against a throttle-body flow model and correcting the estimate from the error.

The patents describe methods. They do not show which one a particular production ECU uses. The value is shared with other controllers: Audi's 09G gearbox document lists altitude information among the data the engine ECU sends to the gearbox (see gearbox and TCU tuning).

Fuelling: MAF, speed-density and alpha-N

A hot-film or hot-wire airflow meter responds to air mass, so the fuelling calculation follows the lower density at altitude without a separate correction. See MAF calibration across ECU types.

A speed-density system calculates charge from absolute manifold pressure, temperature and a volumetric-efficiency table. Haltech provides a barometric correction map on top of this for MAP-load engines, using either a fixed entered pressure, which the manual calls only a basic approach, the power-up reading, or a continuously read sensor (manufacturer documentation for one standalone ECU).

Alpha-N, where load is throttle angle and engine speed, has no pressure term at all. The same manual requires a barometric sensor, internal or an external 1 bar sensor open to atmosphere, when throttle position is the load input. Without a live pressure signal an alpha-N engine keeps the fuelling of the altitude at which it was started. One owner report of an alpha-N engine on a standalone ECU that reads barometric pressure only at start-up describes rich running after a climb of about 3,000 ft and lean running after the reverse descent (anecdote, single source).

Turbocharged engines: the same boost costs more

Compressor pressure ratio is absolute outlet pressure divided by absolute inlet pressure. If the ECU holds the same absolute manifold pressure while the inlet pressure falls, the ratio rises. As arithmetic from the table above, 200 kPa absolute is a ratio of about 1.97 at sea level and 2.52 at 2,000 m, before intake losses. Garrett's own worked example shows that even the same gauge boost costs more: 12 psi of boost with a 1 psi intake depression is a ratio of 1.95 at sea level and 2.14 at Denver's 5,000 ft. On a compressor map a higher pressure ratio lies on a higher turbo-speed line, and Garrett notes that past the choke limit speed rises very quickly and overspeed becomes very likely (manufacturer documentation).

A DaimlerChrysler boost-limiting patent states the consequence: at high altitude, or with a dirty air filter, compressor inlet pressure drops, the ratio for a given boost pressure increases, and the risk of compressor surge or turbocharger overspeed rises. It adds that excessive charge-air temperature after the compressor can damage hoses and compressor blades.

A BorgWarner engineer quoted in the trade press gives a rule of thumb of 1 to 2% more turbocharger speed per 1,000 ft of elevation. BorgWarner's own service bulletin says of a turbocharger run beyond its rated speed that failure is a matter of when.

The protections that reduce boost and torque

Manufacturers do not hold sea-level output to any height. Published approaches include:

  • A maximum boost pressure calculated from the pressure and temperature ahead of the compressor, air mass flow and engine speed, which replaces a fixed worst-case limit so that full boost is available in normal conditions and less at altitude (DaimlerChrysler patent).
  • A torque reduction as a function of barometric pressure and engine speed, to prevent turbocharger overspeed and compressor surge (Detroit Diesel patent, heavy-duty diesel).
  • A maximum turbocharger-speed setpoint reduced by a factor indexed on ambient pressure, with a torque limitation acting when predicted turbo speed approaches it. These labels appear in an unverified public definition file for one petrol ECU, described in the Simos 19.3 SCQ110 turbo-speed protection reference.

Bosch states in general terms that atmospheric pressure affects boost-pressure control and torque limitation in its diesel systems. Boost control itself is covered in electronic boost control and forced induction.

Diesel smoke limit, EGR and injection timing

A diesel has no throttle-governed mixture, so the correction is applied to fuel. Bosch explains that less air enters the cylinder at altitude and the injected quantity must be reduced accordingly or excessive soot results. The same handbook states that EGR and boost setpoints are corrected from the atmospheric-pressure sensor and that start of injection can be adapted for ambient pressure. The air-based fuel limit is described in diesel smoke limits.

Ignition and knock

Petrol of 85 AKI is sold as regular in the high-altitude Rocky Mountain states of the United States. The reason given is that thinner air lowers cylinder pressure and with it the tendency to knock, a statement that is uncited in the reference reporting it, which also notes that the grade is not recommended for modern fuel-injected vehicles. By the same reasoning a turbocharged engine that holds its absolute manifold pressure gains no knock margin from altitude. See knock control.

Why a remap should keep the altitude derates

A calibration proven on a low-altitude dyno has only been tested in the cells of the ambient-pressure corrections that apply near 100 kPa. Raising the boost target raises pressure ratio at every altitude, so the turbocharger starts closer to its speed limit before the 1 to 2% per 1,000 ft is added. Flattening or disabling the ambient-pressure corrections removes the one function that would have reduced boost on a mountain road. The corrections and the turbo-speed and temperature limits should stay active, and logged ambient pressure, boost target and turbo speed, where available, show whether they are working. General limits of a remap are in ECU remapping.

Dyno correction factors

Dyno correction is a reporting convention, not an ECU function. SAE J1349 corrects measured power to 25 °C and 99 kPa dry air, and is intended for 15 to 35 °C and 900 to 1,050 mbar. Its purpose is to let runs made in different weather be compared, and its intended pressure range does not reach the pressures found above roughly 1,000 m. See dyno graphs explained.

Not established

  • The altitude at which a specific production petrol engine begins to reduce boost, and the compressor-outlet temperature limit used, are not given in the manufacturer documents cited.
  • Idle-speed, idle-air and ignition-map corrections for altitude are not described in the sources cited.
  • Whether J1349-type correction is valid for boost-controlled engines is not stated in the sources cited.

Sources