Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
AEM Infinity 508
Applies to
AEM Infinity 508
Tool groups
None
Manufacturers
None

The AEM Infinity 508 (part numbers 30-7108 and 30-7112) uses a single 80-pin harness connector, designated C1, from the Molex MX123 family (the manufacturer's 30-3704 Infinity Series 5 plug and pin kit supplies an 80-pin MX123 connector). The assignments below follow AEM's Series 5 universal pinout, a manufacturer document that also covers the Infinity 506 (30-7106). Where the table gives model-specific variants, the 508 uses injector 7 and 8 on pins 3 and 4 and coil 7 and 8 on pins 31 and 32; the 506 uses those pins for low-side outputs and digital inputs.

Orientation and numbering

The cited document lists the pins in a table and does not show the connector face, cavity layout or viewing direction. The redrawn diagram is therefore a numbered pin index in a regular grid and does not represent the physical cavity positions. Verify orientation against the physical connector before probing.

Notable functions

Pin 10 is permanent battery power and must be powered before the ignition input on pin 48 is triggered. Coil outputs (pins 11 to 16, plus 31 and 32 on the 508) are 0-5 V falling-edge signals with 25 mA maximum source current and must drive an ignitor, not a coil primary directly. Injector outputs 1 to 6 are on pins 78, 77, 76, 66, 65 and 64; per AEM, injector 7 and 8 on pins 3 and 4 are for high-impedance injectors only and are available on 30-7108 only. Pins 5 to 9 form the internal wideband (UEGO 1) interface for a Bosch sensor. Pins 34 to 37 are the two CAN channels, and pin 72 is the flash enable input. The manufacturer table also gives current ratings, pull-ups and set-up notes for each pin.

Diagram redrawn by Tuning Wiki from the AEM Infinity Hardware Specification 30-7106/7108/7112.

Not established

The physical cavity arrangement and viewing side of the connector are not stated in the cited document.

Sources

Connector pinout

Applicability

AEM Infinity-Series5 universal pinout (30-7106/7108/7112, document build 20 January 2021). Manufacturer documentation. Pins shared between models carry both functions where AEM lists model-specific variants (506 vs 508).

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

C1 (80-pin Molex MX123 harness connector)

Redrawn pin index
View: Pin index only; connector face orientation and cavity layout are not shown in the cited AEM document.
C1 (80-pin Molex MX123 harness connector) — Redrawn pin index. Pin index only; connector face orientation and cavity layout are not shown in the cited AEM document.

Select a pin in a photograph or the index to highlight it.

C1 (80-pin Molex MX123 harness connector) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Lowside 4
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 5
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 6 (506 only) / Injector 7 (508 only)
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 7 (506 only) / Injector 8 (508 only)
Cavity: Populated
Confirmed

AEM hardware spec 2021

UEGO 1 Heat
Cavity: Populated
Confirmed

AEM hardware spec 2021

UEGO 1 IA
Cavity: Populated
Confirmed

AEM hardware spec 2021

UEGO 1 IP
Cavity: Populated
Confirmed

AEM hardware spec 2021

UEGO 1 UN
Cavity: Populated
Confirmed

AEM hardware spec 2021

UEGO 1 VM
Cavity: Populated
Confirmed

AEM hardware spec 2021

Battery Perm Power
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 4
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 1
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 6
Cavity: Populated
Confirmed

AEM hardware spec 2021

Coil 5
Cavity: Populated
Confirmed

AEM hardware spec 2021

Crankshaft Position Sensor VR+
Cavity: Populated
Confirmed

AEM hardware spec 2021

Crankshaft Position Sensor VR-
Cavity: Populated
Confirmed

AEM hardware spec 2021

Camshaft Position Sensor 1 VR-
Cavity: Populated
Confirmed

AEM hardware spec 2021

Camshaft Position Sensor 1 VR+
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog Sensor Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog Sensor Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

Crankshaft Position Sensor Hall
Cavity: Populated
Confirmed

AEM hardware spec 2021

Camshaft Position Sensor 1 Hall
Cavity: Populated
Confirmed

AEM hardware spec 2021

Digital 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Dig3 [Hz] / Dig3 Duty
Cavity: Populated
Confirmed

AEM hardware spec 2021

Dig4 [Hz] / Dig4 Duty / RS232 Rx
Cavity: Populated
Confirmed

AEM hardware spec 2021

Digital 5 / RS232 Tx
Cavity: Populated
Confirmed

AEM hardware spec 2021

Dig6 [Hz] / Dig6 Duty (506 only) / Coil 7 (508 only)
Cavity: Populated
Confirmed

AEM hardware spec 2021

Digital 7 (506 only) / Coil 8 (508 only)
Cavity: Populated
Confirmed

AEM hardware spec 2021

Battery Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

CANL A
Cavity: Populated
Confirmed

AEM hardware spec 2021

CANH A
Cavity: Populated
Confirmed

AEM hardware spec 2021

CanL B
Cavity: Populated
Confirmed

AEM hardware spec 2021

CanH B
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog Temp 1
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog Temp 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog Temp 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 0
Cavity: Populated
Confirmed

AEM hardware spec 2021

Lowside 1
Cavity: Populated
Confirmed

AEM hardware spec 2021

Battery Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

Knock Sensor 1
Cavity: Populated
Confirmed

AEM hardware spec 2021

Knock Sensor 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Battery Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

EFI Main Relay Switched Ground Output
Cavity: Populated
Confirmed

AEM hardware spec 2021

Ignition Switch
Cavity: Populated
Confirmed

AEM hardware spec 2021

+5V Sensor Power
Cavity: Populated
Confirmed

AEM hardware spec 2021

+5V Sensor Power
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 7
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 8
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 9
Cavity: Populated
Confirmed

AEM hardware spec 2021

VR+ 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

VR- 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

VR- 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

VR+ 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

Highside 0
Cavity: Populated
Confirmed

AEM hardware spec 2021

Stepper 1B
Cavity: Populated
Confirmed

AEM hardware spec 2021

Stepper 2B
Cavity: Populated
Confirmed

AEM hardware spec 2021

DBW1 Motor -
Cavity: Populated
Confirmed

AEM hardware spec 2021

DBW1 Motor +
Cavity: Populated
Confirmed

AEM hardware spec 2021

Main Relay Power Input
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 6
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 5
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 4
Cavity: Populated
Confirmed

AEM hardware spec 2021

Battery Ground
Cavity: Populated
Confirmed

AEM hardware spec 2021

Main Relay Power Input
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 19
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 18
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 16
Cavity: Populated
Confirmed

AEM hardware spec 2021

Flash Enable
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 13
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 11
Cavity: Populated
Confirmed

AEM hardware spec 2021

Analog 10
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 3
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 2
Cavity: Populated
Confirmed

AEM hardware spec 2021

Injector 1
Cavity: Populated
Confirmed

AEM hardware spec 2021

Stepper 2A
Cavity: Populated
Confirmed

AEM hardware spec 2021

Stepper 1A
Cavity: Populated
Confirmed

AEM hardware spec 2021