The AEM Infinity 508 (part numbers 30-7108 and 30-7112) uses a single 80-pin harness connector, designated C1, from the Molex MX123 family (the manufacturer's 30-3704 Infinity Series 5 plug and pin kit supplies an 80-pin MX123 connector). The assignments below follow AEM's Series 5 universal pinout, a manufacturer document that also covers the Infinity 506 (30-7106). Where the table gives model-specific variants, the 508 uses injector 7 and 8 on pins 3 and 4 and coil 7 and 8 on pins 31 and 32; the 506 uses those pins for low-side outputs and digital inputs.
Orientation and numbering
The cited document lists the pins in a table and does not show the connector face, cavity layout or viewing direction. The redrawn diagram is therefore a numbered pin index in a regular grid and does not represent the physical cavity positions. Verify orientation against the physical connector before probing.
Notable functions
Pin 10 is permanent battery power and must be powered before the ignition input on pin 48 is triggered. Coil outputs (pins 11 to 16, plus 31 and 32 on the 508) are 0-5 V falling-edge signals with 25 mA maximum source current and must drive an ignitor, not a coil primary directly. Injector outputs 1 to 6 are on pins 78, 77, 76, 66, 65 and 64; per AEM, injector 7 and 8 on pins 3 and 4 are for high-impedance injectors only and are available on 30-7108 only. Pins 5 to 9 form the internal wideband (UEGO 1) interface for a Bosch sensor. Pins 34 to 37 are the two CAN channels, and pin 72 is the flash enable input. The manufacturer table also gives current ratings, pull-ups and set-up notes for each pin.
Diagram redrawn by Tuning Wiki from the AEM Infinity Hardware Specification 30-7106/7108/7112.
Not established
The physical cavity arrangement and viewing side of the connector are not stated in the cited document.
Sources
- Infinity Hardware Specification 30-7106/7108/7112. AEM Performance Electronics manufacturer document, build 20 January 2021. Accessed 19 November 2026.
Connector pinout
AEM Infinity-Series5 universal pinout (30-7106/7108/7112, document build 20 January 2021). Manufacturer documentation. Pins shared between models carry both functions where AEM lists model-specific variants (506 vs 508).
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
C1 (80-pin Molex MX123 harness connector)
View: Pin index only; connector face orientation and cavity layout are not shown in the cited AEM document.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Lowside 4 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 5 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 6 (506 only) / Injector 7 (508 only) Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 7 (506 only) / Injector 8 (508 only) Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| UEGO 1 Heat Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| UEGO 1 IA Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| UEGO 1 IP Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| UEGO 1 UN Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| UEGO 1 VM Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Battery Perm Power Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 4 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 1 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 6 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Coil 5 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Crankshaft Position Sensor VR+ Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Crankshaft Position Sensor VR- Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Camshaft Position Sensor 1 VR- Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Camshaft Position Sensor 1 VR+ Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog Sensor Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog Sensor Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Crankshaft Position Sensor Hall Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Camshaft Position Sensor 1 Hall Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Digital 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Dig3 [Hz] / Dig3 Duty Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Dig4 [Hz] / Dig4 Duty / RS232 Rx Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Digital 5 / RS232 Tx Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Dig6 [Hz] / Dig6 Duty (506 only) / Coil 7 (508 only) Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Digital 7 (506 only) / Coil 8 (508 only) Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Battery Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| CANL A Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| CANH A Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| CanL B Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| CanH B Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog Temp 1 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog Temp 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog Temp 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 0 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Lowside 1 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Battery Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Knock Sensor 1 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Knock Sensor 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Battery Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| EFI Main Relay Switched Ground Output Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Ignition Switch Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| +5V Sensor Power Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| +5V Sensor Power Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 7 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 8 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 9 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| VR+ 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| VR- 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| VR- 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| VR+ 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Highside 0 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Stepper 1B Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Stepper 2B Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| DBW1 Motor - Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| DBW1 Motor + Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Main Relay Power Input Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 6 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 5 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 4 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Battery Ground Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Main Relay Power Input Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 19 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 18 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 16 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Flash Enable Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 13 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 11 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Analog 10 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 3 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 2 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Injector 1 Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Stepper 2A Cavity: Populated |
Confirmed AEM hardware spec 2021 |
||
| Stepper 1A Cavity: Populated |
Confirmed AEM hardware spec 2021 |