Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Peugeot

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

After the XU-powered cars covered in the classic GTI guide, Peugeot's small-hatch GTIs moved to the TU 1.6 sixteen-valve (106 GTI), the EW10 2.0 (206 GTi 180 / RC) and the turbocharged 1.6 THP (207 RC and GTI, 208 GTI, 308 GTI). Most public tuning information for these cars is tuner marketing or owner reports, and the figures differ between sources. This page records what is stated and flags how reliable each statement is. It is an orientation guide, not a set of tuning targets.

Engines and factory outputs

CarEngineFactory output (as listed)Source 106 GTI, Saxo VTS, C2 VTSTU5J4 (NFX), 1.6 16v, catalyst120 PSWikipedia: PSA TU engine Lower-power 1.6 16v variantTU5JP4 (NFU)110 PSSame page 106 RallyeTU2J2/Z (MFZ), Magneti Marelli injection, catalyst100 PSSame page 206 GTi 180 (called 206 RC in European markets)EW10J4S, 2.0 16v177 hp in tuner listingsTuner listings 207 RC and GTI THP1.6 THP (EP6DTS on the 175 hp car)175 hpTuner listings 208 GTI1.6 THP (the later 208 hp car is listed as EP6CDTX, a different engine code from the 207's EP6DTS)200 and 208 hp variantsTuner listings 308 II GTI1.6 e-THP263 hpTuner listings

The Wikipedia TU page does not list a 106 S16 and does not link these variants to ECU types, so check the ECU label on the actual car rather than assuming from the badge.

106 GTI and other TU cars

For the 106 and other TU 1.0 to 1.6 eight-valve engines, a vendor of throttle body kits states that the ECU must be remapped after a throttle body conversion. That is a vendor instruction, but the point is general: new airflow needs the fuel and ignition maps changed.

Vendor stage packages for the TU5J4 (106 GTI and Saxo VTS)

One UK supplier, Peugeot Tuning Parts, sells staged packages for the TU5J4. The power figures are the vendor's own typical results at the flywheel, with no independent verification, and none of the listings carry customer reviews.

PackageContents (vendor)Quoted result Stage 2Cat Cams 1321743 or Newman PH3 Ultimate Road cams, an ECU remap tuned for the package (the ECU is sent to the vendor), optional exhaust manifoldAbout 150 bhp at 7,700 rpm and 114 lb-ft at 6,000 rpm Stage 3Newman PH3 cams, throttle bodies (AT Power direct-to-head or Jenvey ST45) with fuel rail, air horns and throttle position sensor, optional Emerald K6+ ECU, optional exhaust manifold. Aimed at a standard bottom end.About 167 bhp at 7,700 rpm and 120 lb-ft at 6,300 rpm; dyno mapping stated as required Stage 4Cat Cams 1321737 or Newman PH4 rally cams, valves and springs, forged high-compression pistons and rods, bearings, throttle bodies, 250 cc injectors, Emerald K6+ ECU185 to 195 bhp; dyno mapping stated as required, and the vendor recommends professional cam timing

The stages show the shape of a typical TU5J4 build: cams and a remap first, throttle bodies and standalone management next, and a forged bottom end for the highest outputs. Owner reports are lower. Estimates in forum discussions put a mapped Cat Cams 1321743 set-up at roughly 155 to 160 bhp at the flywheel, and one owner reports 157.2 bhp on a TU5JP4 with a modified head, cams, a de-catted exhaust and an Adaptronic ECU. Those are self-reported and not verified. I did not find reliable dyno data on the NFX inlet manifold or standard exhaust for the 106 GTI itself.

Forced induction on the TU5J4

I found no dyno-verified boost results for a 106 GTI turbo or supercharger, only parts listings and general advice. An owner's turbo write-up lists an adapter, downpipe, oil feed and return, boost pipes, an intercooler and a tubular manifold, and recommends forged pistons as a safety margin at higher boost. Forged piston kits for the TU5J4 and TU5JP4 are sold in several compression ratios, including turbo-specific sets around 9.0 to 1 and higher-compression sets above 12 to 1 for naturally aspirated use. Compression is the main lever for boost tolerance, but the sources give no recommended ratio for a given boost level, so confirm with the engine builder and a mapped dyno session.

106 Rallye

The Series 1 Rallye used the 1.3 TU2J2 and the Series 2 the 1.6 TU5J2, both with Magneti Marelli multipoint injection. A manufacturer-era table lists the 1993 to 1996 1.3 TU2J2L/Z (MFZ) with a Magneti Marelli 8P ECU. Retailers label some cam listings as TU24, which also cover the 1.3 Rallye, so check the engine code. One supplier lists a fast-road cam for the 1.3 Rallye with a 284 degree inlet duration and a claimed gain of 12 bhp; that is a vendor claim. I found no verified Rallye remap or piggyback data.

206 GTi 180 / RC

The EW10J4S car is a more highly tuned development of the 138 hp 2.0 engine, which is one reason owners say there is little to gain from simple bolt-ons. The following comes from vendor listings and a 2012 owner discussion on the 206 Info Exchange forum. These are anecdotes, not controlled tests.

A cat-back exhaust is reported to add about 5 bhp. One owner went from a measured 169 bhp to 174 bhp with a cat-back, panel filter and remap. Induction kits get a poor report: one owner measured a loss of 12 bhp on rollers after fitting one, and others warn that kits can draw in warm air. A lower airbox with a panel filter is the more commonly recommended intake change. Cams are described as the only route to a worthwhile gain, though some owners report running problems with cams, and one reports about 195 hp with cams and the usual supporting modifications. A remap alone is described as variable between cars.

The Cat Cams 4901804 Ultimate Road cams are listed for the EW10J4S with variable valve timing. The listing gives 256 degrees duration at 0.1 mm (228 at 1.0 mm), lift of 10.75 mm inlet and 10.25 mm exhaust, a billet inlet cam drilled for the VVT, and a separate VVT-delete version (4902804). The vendor claims up to 17 bhp with a remap and says a remap is essential; its single listed review reports 172 to 191 ps, which is one anecdote. A second Cat Cams set, the 4901613 sport cam, is advertised by the same vendor at up to 23 bhp and 24 lb-ft with a remap or piggyback ECU. All of these are seller figures.

The only throttle body example found is a car on a Megasquirt ECU that went from 142 whp to 161.9 whp with individual throttle bodies and a remap. That is a single best run with a different ECU, not a clean comparison of the intake change.

207 RC, 208 GTI and 308 GTI THP

These turbocharged cars respond much more to software than the naturally aspirated ones. Vendor figures include:

207 RC / GTi THP 175: one tuner reports about 190 bhp from a measured 178 bhp, with an extra 25 bhp in the midrange. Tuner listings give 175 hp and 240 Nm standard, with stage 1 around +28 hp and stage 2 around +52 hp, and another listing gives 205 hp on stage 1 and 230 hp on stage 2. Check which engine variant a listing refers to, since a 150 hp 207 1.6 THP is also tuned and shows different gains. 208 GTI 208 hp (2015 to 2019): a tuner listing gives stage 1 around +12 hp and stage 2 around +21 hp on the 208 hp baseline. Do not mix these with the 207 figures, because the engine code differs. A general 207 guide lists a sports exhaust, panel filter and remap as a typical first step and says a remap gives the best value. Tuners also list stage 1 files for the 208 GTI 1.6 THP in both 200 and 208 hp forms and for the 308 GTI 1.6 e-THP 263.

An engine reference for the EP6 family marks early versions as a tuning risk because of timing-chain concerns, which is a reminder to check chain condition before adding power. These are marketing figures. Boost, fuelling, knock and intake temperature at the point of measurement matter far more than a headline number. For engine-specific diagnosis and Bosch MED17 details, see the PSA 1.6 THP MED17 tuning guide, and for ECU identification see the PSA ECU identification and tuning guide.

Reading tuning claims on these cars

Check what the figure is: wheel or flywheel, corrected or uncorrected, same rolling road before and after. A remap sold as generic rather than mapped to the individual car is generally expected to give less than a rolling-road map. Vendor packages that depend on dyno mapping give their best figures only after that mapping, so a bolt-on kit without it should not be expected to match the quoted result. Keep the original ECU read and know how to restore it before writing anything. Gaps: public sources for the 106 GTI standard intake and exhaust, 106 forced induction results and independent 206 GTi 180 cam results were thin. If you have dyno sheets, part numbers or workshop data for these engines, they would improve this page.

Related pages

Peugeot GTI tuning guide: 205, 309, 405 Mi16 and 306 S16 XU engines PSA 1.6 THP MED17 tuning guide PSA ECU identification and tuning guide

Sources

Wikipedia: PSA TU engine Peugeot Tuning Parts: 106 GTI Stage 2 package Peugeot Tuning Parts: 106 GTI Stage 3 package Peugeot Tuning Parts: 106 GTI Stage 4 package Peugeot Tuning Parts: Cat Cams 4901804 for the 206 GTI 180 / RC Oreca Store: Cat Cams for TU5J2/TU24 (106 Rallye) Forged piston listings for the TU5J4 and TU5JP4 Vendor throttle body kit for TU 1.0 to 1.6 8v engines 206 Info Exchange: 206 GTi 180 performance discussion (2012) Tuner listing: 206 2.0 16v GTi General 207 tuning guide Superchips 207 GTi THP upgrade report Tuner listing: 207 RC 1.6 THP Tuner listing: 208 GTI 1.6 THP Engine reference: PSA EP6 / THP

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Peugeot 106, 206, 207 and 208 GTI tuning overview

After the XU-powered cars covered in the classic GTI guide, Peugeot's small-hatch GTIs moved to the TU 1.6 sixteen-valve (106 GTI), the EW10 2.0 (206 GTi 180 / RC) and the turbocharged 1.6 THP (207 RC and GTI, 208 GTI, 308 GTI). Most public tuning information for these cars is tuner marketing or owner reports, and the figures differ between sources. This page records what is stated and flags how reliable each statement is. It is an orientation guide, not a set of tuning targets.

Engines and factory outputs

CarEngineFactory output (as listed)Source
106 GTI, Saxo VTS, C2 VTSTU5J4 (NFX), 1.6 16v, catalyst120 PSWikipedia: PSA TU engine
Lower-power 1.6 16v variantTU5JP4 (NFU)110 PSSame page
106 RallyeTU2J2/Z (MFZ), Magneti Marelli injection, catalyst100 PSSame page
206 GTi 180 (called 206 RC in European markets)EW10J4S, 2.0 16v177 hp in tuner listingsTuner listings
207 RC and GTI THP1.6 THP (EP6DTS on the 175 hp car)175 hpTuner listings
208 GTI1.6 THP (the later 208 hp car is listed as EP6CDTX, a different engine code from the 207's EP6DTS)200 and 208 hp variantsTuner listings
308 II GTI1.6 e-THP263 hpTuner listings

The Wikipedia TU page does not list a 106 S16 and does not link these variants to ECU types, so check the ECU label on the actual car rather than assuming from the badge.

106 GTI and other TU cars

For the 106 and other TU 1.0 to 1.6 eight-valve engines, a vendor of throttle body kits states that the ECU must be remapped after a throttle body conversion. That is a vendor instruction, but the point is general: new airflow needs the fuel and ignition maps changed.

Vendor stage packages for the TU5J4 (106 GTI and Saxo VTS)

One UK supplier, Peugeot Tuning Parts, sells staged packages for the TU5J4. The power figures are the vendor's own typical results at the flywheel, with no independent verification, and none of the listings carry customer reviews.

PackageContents (vendor)Quoted result
Stage 2Cat Cams 1321743 or Newman PH3 Ultimate Road cams, an ECU remap tuned for the package (the ECU is sent to the vendor), optional exhaust manifoldAbout 150 bhp at 7,700 rpm and 114 lb-ft at 6,000 rpm
Stage 3Newman PH3 cams, throttle bodies (AT Power direct-to-head or Jenvey ST45) with fuel rail, air horns and throttle position sensor, optional Emerald K6+ ECU, optional exhaust manifold. Aimed at a standard bottom end.About 167 bhp at 7,700 rpm and 120 lb-ft at 6,300 rpm; dyno mapping stated as required
Stage 4Cat Cams 1321737 or Newman PH4 rally cams, valves and springs, forged high-compression pistons and rods, bearings, throttle bodies, 250 cc injectors, Emerald K6+ ECU185 to 195 bhp; dyno mapping stated as required, and the vendor recommends professional cam timing

The stages show the shape of a typical TU5J4 build: cams and a remap first, throttle bodies and standalone management next, and a forged bottom end for the highest outputs. Owner reports are lower. Estimates in forum discussions put a mapped Cat Cams 1321743 set-up at roughly 155 to 160 bhp at the flywheel, and one owner reports 157.2 bhp on a TU5JP4 with a modified head, cams, a de-catted exhaust and an Adaptronic ECU. Those are self-reported and not verified. I did not find reliable dyno data on the NFX inlet manifold or standard exhaust for the 106 GTI itself.

Forced induction on the TU5J4

I found no dyno-verified boost results for a 106 GTI turbo or supercharger, only parts listings and general advice. An owner's turbo write-up lists an adapter, downpipe, oil feed and return, boost pipes, an intercooler and a tubular manifold, and recommends forged pistons as a safety margin at higher boost. Forged piston kits for the TU5J4 and TU5JP4 are sold in several compression ratios, including turbo-specific sets around 9.0 to 1 and higher-compression sets above 12 to 1 for naturally aspirated use. Compression is the main lever for boost tolerance, but the sources give no recommended ratio for a given boost level, so confirm with the engine builder and a mapped dyno session.

106 Rallye

The Series 1 Rallye used the 1.3 TU2J2 and the Series 2 the 1.6 TU5J2, both with Magneti Marelli multipoint injection. A manufacturer-era table lists the 1993 to 1996 1.3 TU2J2L/Z (MFZ) with a Magneti Marelli 8P ECU. Retailers label some cam listings as TU24, which also cover the 1.3 Rallye, so check the engine code. One supplier lists a fast-road cam for the 1.3 Rallye with a 284 degree inlet duration and a claimed gain of 12 bhp; that is a vendor claim. I found no verified Rallye remap or piggyback data.

206 GTi 180 / RC

The EW10J4S car is a more highly tuned development of the 138 hp 2.0 engine, which is one reason owners say there is little to gain from simple bolt-ons. The following comes from vendor listings and a 2012 owner discussion on the 206 Info Exchange forum. These are anecdotes, not controlled tests.

  • A cat-back exhaust is reported to add about 5 bhp. One owner went from a measured 169 bhp to 174 bhp with a cat-back, panel filter and remap.
  • Induction kits get a poor report: one owner measured a loss of 12 bhp on rollers after fitting one, and others warn that kits can draw in warm air. A lower airbox with a panel filter is the more commonly recommended intake change.
  • Cams are described as the only route to a worthwhile gain, though some owners report running problems with cams, and one reports about 195 hp with cams and the usual supporting modifications. A remap alone is described as variable between cars.

The Cat Cams 4901804 Ultimate Road cams are listed for the EW10J4S with variable valve timing. The listing gives 256 degrees duration at 0.1 mm (228 at 1.0 mm), lift of 10.75 mm inlet and 10.25 mm exhaust, a billet inlet cam drilled for the VVT, and a separate VVT-delete version (4902804). The vendor claims up to 17 bhp with a remap and says a remap is essential; its single listed review reports 172 to 191 ps, which is one anecdote. A second Cat Cams set, the 4901613 sport cam, is advertised by the same vendor at up to 23 bhp and 24 lb-ft with a remap or piggyback ECU. All of these are seller figures.

The only throttle body example found is a car on a Megasquirt ECU that went from 142 whp to 161.9 whp with individual throttle bodies and a remap. That is a single best run with a different ECU, not a clean comparison of the intake change.

207 RC, 208 GTI and 308 GTI THP

These turbocharged cars respond much more to software than the naturally aspirated ones. Vendor figures include:

  • 207 RC / GTi THP 175: one tuner reports about 190 bhp from a measured 178 bhp, with an extra 25 bhp in the midrange. Tuner listings give 175 hp and 240 Nm standard, with stage 1 around +28 hp and stage 2 around +52 hp, and another listing gives 205 hp on stage 1 and 230 hp on stage 2. Check which engine variant a listing refers to, since a 150 hp 207 1.6 THP is also tuned and shows different gains.
  • 208 GTI 208 hp (2015 to 2019): a tuner listing gives stage 1 around +12 hp and stage 2 around +21 hp on the 208 hp baseline. Do not mix these with the 207 figures, because the engine code differs.
  • A general 207 guide lists a sports exhaust, panel filter and remap as a typical first step and says a remap gives the best value.
  • Tuners also list stage 1 files for the 208 GTI 1.6 THP in both 200 and 208 hp forms and for the 308 GTI 1.6 e-THP 263.

An engine reference for the EP6 family marks early versions as a tuning risk because of timing-chain concerns, which is a reminder to check chain condition before adding power. These are marketing figures. Boost, fuelling, knock and intake temperature at the point of measurement matter far more than a headline number. For engine-specific diagnosis and Bosch MED17 details, see the PSA 1.6 THP MED17 tuning guide, and for ECU identification see the PSA ECU identification and tuning guide.

Reading tuning claims on these cars

  • Check what the figure is: wheel or flywheel, corrected or uncorrected, same rolling road before and after.
  • A remap sold as generic rather than mapped to the individual car is generally expected to give less than a rolling-road map.
  • Vendor packages that depend on dyno mapping give their best figures only after that mapping, so a bolt-on kit without it should not be expected to match the quoted result.
  • Keep the original ECU read and know how to restore it before writing anything.
  • Gaps: public sources for the 106 GTI standard intake and exhaust, 106 forced induction results and independent 206 GTi 180 cam results were thin. If you have dyno sheets, part numbers or workshop data for these engines, they would improve this page.

Related pages

Sources

Revision 3: Peugeot 106, 206, 207 and 208 GTI tuning overview

After the XU-powered cars covered in the classic GTI guide, Peugeot's small-hatch GTIs moved to the TU 1.6 sixteen-valve (106 GTI), the EW10 2.0 (206 GTi 180 / RC) and the turbocharged 1.6 THP (207 RC and GTI, 208 GTI, 308 GTI). Most public tuning information for these cars is tuner marketing or owner reports, and the figures differ between sources. This page records what is stated and flags how reliable each statement is. It is an orientation guide, not a set of tuning targets.

Engines and factory outputs

CarEngineFactory output (as listed)Source
106 GTI, Saxo VTS, C2 VTSTU5J4 (NFX), 1.6 16v, catalyst120 PSWikipedia: PSA TU engine
Lower-power 1.6 16v variantTU5JP4 (NFU)110 PSSame page
106 RallyeTU2J2/Z (MFZ), Magneti Marelli injection, catalyst100 PSSame page
206 GTi 180 (called 206 RC in European markets)EW10J4S, 2.0 16v177 hp in tuner listingsTuner listings
207 RC and GTI THP1.6 THP (EP6DTS on the 175 hp car)175 hpTuner listings
208 GTI1.6 THP (the later 208 hp car is listed as EP6CDTX, a different engine code from the 207's EP6DTS)200 and 208 hp variantsTuner listings
308 II GTI1.6 e-THP263 hpTuner listings

The Wikipedia TU page does not list a 106 S16 and does not link these variants to ECU types, so check the ECU label on the actual car rather than assuming from the badge.

106 GTI and other TU cars

For the 106 and other TU 1.0 to 1.6 eight-valve engines, a vendor of throttle body kits states that the ECU must be remapped after a throttle body conversion. That is a vendor instruction, but the point is general: new airflow needs the fuel and ignition maps changed.

Vendor stage packages for the TU5J4 (106 GTI and Saxo VTS)

One UK supplier, Peugeot Tuning Parts, sells staged packages for the TU5J4. The power figures are the vendor's own typical results at the flywheel, with no independent verification, and none of the listings carry customer reviews.

PackageContents (vendor)Quoted result
Stage 2Cat Cams 1321743 or Newman PH3 Ultimate Road cams, an ECU remap tuned for the package (the ECU is sent to the vendor), optional exhaust manifoldAbout 150 bhp at 7,700 rpm and 114 lb-ft at 6,000 rpm
Stage 3Newman PH3 cams, throttle bodies (AT Power direct-to-head or Jenvey ST45) with fuel rail, air horns and throttle position sensor, optional Emerald K6+ ECU, optional exhaust manifold. Aimed at a standard bottom end.About 167 bhp at 7,700 rpm and 120 lb-ft at 6,300 rpm; dyno mapping stated as required
Stage 4Cat Cams 1321737 or Newman PH4 rally cams, valves and springs, forged high-compression pistons and rods, bearings, throttle bodies, 250 cc injectors, Emerald K6+ ECU185 to 195 bhp; dyno mapping stated as required, and the vendor recommends professional cam timing

The stages show the shape of a typical TU5J4 build: cams and a remap first, throttle bodies and standalone management next, and a forged bottom end for the highest outputs. Owner reports are lower. Estimates in forum discussions put a mapped Cat Cams 1321743 set-up at roughly 155 to 160 bhp at the flywheel, and one owner reports 157.2 bhp on a TU5JP4 with a modified head, cams, a de-catted exhaust and an Adaptronic ECU. Those are self-reported and not verified. I did not find reliable dyno data on the NFX inlet manifold or standard exhaust for the 106 GTI itself.

Forced induction on the TU5J4

I found no dyno-verified boost results for a 106 GTI turbo or supercharger, only parts listings and general advice. An owner's turbo write-up lists an adapter, downpipe, oil feed and return, boost pipes, an intercooler and a tubular manifold, and recommends forged pistons as a safety margin at higher boost. Forged piston kits for the TU5J4 and TU5JP4 are sold in several compression ratios, including turbo-specific sets around 9.0 to 1 and higher-compression sets above 12 to 1 for naturally aspirated use. Compression is the main lever for boost tolerance, but the sources give no recommended ratio for a given boost level, so confirm with the engine builder and a mapped dyno session.

106 Rallye

The Series 1 Rallye used the 1.3 TU2J2 and the Series 2 the 1.6 TU5J2, both with Magneti Marelli multipoint injection. A manufacturer-era table lists the 1993 to 1996 1.3 TU2J2L/Z (MFZ) with a Magneti Marelli 8P ECU. Retailers label some cam listings as TU24, which also cover the 1.3 Rallye, so check the engine code. One supplier lists a fast-road cam for the 1.3 Rallye with a 284 degree inlet duration and a claimed gain of 12 bhp; that is a vendor claim. I found no verified Rallye remap or piggyback data.

206 GTi 180 / RC

The EW10J4S car is a more highly tuned development of the 138 hp 2.0 engine, which is one reason owners say there is little to gain from simple bolt-ons. The following comes from vendor listings and a 2012 owner discussion on the 206 Info Exchange forum. These are anecdotes, not controlled tests.

  • A cat-back exhaust is reported to add about 5 bhp. One owner went from a measured 169 bhp to 174 bhp with a cat-back, panel filter and remap.
  • Induction kits get a poor report: one owner measured a loss of 12 bhp on rollers after fitting one, and others warn that kits can draw in warm air. A lower airbox with a panel filter is the more commonly recommended intake change.
  • Cams are described as the only route to a worthwhile gain, though some owners report running problems with cams, and one reports about 195 hp with cams and the usual supporting modifications. A remap alone is described as variable between cars.

The Cat Cams 4901804 Ultimate Road cams are listed for the EW10J4S with variable valve timing. The listing gives 256 degrees duration at 0.1 mm (228 at 1.0 mm), lift of 10.75 mm inlet and 10.25 mm exhaust, a billet inlet cam drilled for the VVT, and a separate VVT-delete version (4902804). The vendor claims up to 17 bhp with a remap and says a remap is essential; its single listed review reports 172 to 191 ps, which is one anecdote. A second Cat Cams set, the 4901613 sport cam, is advertised by the same vendor at up to 23 bhp and 24 lb-ft with a remap or piggyback ECU. All of these are seller figures.

The only throttle body example found is a car on a Megasquirt ECU that went from 142 whp to 161.9 whp with individual throttle bodies and a remap. That is a single best run with a different ECU, not a clean comparison of the intake change.

207 RC, 208 GTI and 308 GTI THP

These turbocharged cars respond much more to software than the naturally aspirated ones. Vendor figures include:

  • 207 RC / GTi THP 175: one tuner reports about 190 bhp from a measured 178 bhp, with an extra 25 bhp in the midrange. Tuner listings give 175 hp and 240 Nm standard, with stage 1 around +28 hp and stage 2 around +52 hp, and another listing gives 205 hp on stage 1 and 230 hp on stage 2. Check which engine variant a listing refers to, since a 150 hp 207 1.6 THP is also tuned and shows different gains.
  • 208 GTI 208 hp (2015 to 2019): a tuner listing gives stage 1 around +12 hp and stage 2 around +21 hp on the 208 hp baseline. Do not mix these with the 207 figures, because the engine code differs.
  • A general 207 guide lists a sports exhaust, panel filter and remap as a typical first step and says a remap gives the best value.
  • Tuners also list stage 1 files for the 208 GTI 1.6 THP in both 200 and 208 hp forms and for the 308 GTI 1.6 e-THP 263.

An engine reference for the EP6 family marks early versions as a tuning risk because of timing-chain concerns, which is a reminder to check chain condition before adding power. These are marketing figures. Boost, fuelling, knock and intake temperature at the point of measurement matter far more than a headline number. For engine-specific diagnosis and Bosch MED17 details, see the PSA 1.6 THP MED17 tuning guide, and for ECU identification see the PSA ECU identification and tuning guide.

Reading tuning claims on these cars

  • Check what the figure is: wheel or flywheel, corrected or uncorrected, same rolling road before and after.
  • A remap sold as generic rather than mapped to the individual car is generally expected to give less than a rolling-road map.
  • Vendor packages that depend on dyno mapping give their best figures only after that mapping, so a bolt-on kit without it should not be expected to match the quoted result.
  • Keep the original ECU read and know how to restore it before writing anything.
  • Gaps: public sources for the 106 GTI standard intake and exhaust, 106 forced induction results and independent 206 GTi 180 cam results were thin. If you have dyno sheets, part numbers or workshop data for these engines, they would improve this page.

Related pages

Sources