Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Citroën, Peugeot

Changes from revision 9 to revision 9

Removed text is struck through; added text is highlighted.

Older Peugeot and Citroën diesels include mechanical injection pumps and electronically managed rotary-pump systems. Identify the engine code, exact pump maker and part number, ECU where fitted, vehicle and emissions equipment before choosing service information or considering tuning. These systems do not all use the same controls and cannot be treated as interchangeable with common-rail HDi.

Identify the injection system first

Citroën's XM technical summary lists three distinct examples: the 2.1 Turbo D XUD11 ATE/L with a mechanical pump; XUD11 BTE/L with Lucas Diesel EPIC electronic injection; and 2.5 Turbo D DK5 ATE/L3 with Bosch MSA 11 7.6 and VP36 electronic injection. The document concerns specific multiplexed XM versions and model years; it is not an all-market year cutoff or proof that every XUD pump is mechanical.

Snap-on's 2013 vehicle-communication manual lists both Lucas and Bosch VP20 equipment for the 1.9 turbo diesel DHX in selected Xantia, Evasion, Jumpy, 406, 806 and Expert examples, and lists Lucas or Bosch VP20 for Citroën Saxo 1.5 VJY/VJZ. It is a diagnostic selection guide, not proof of the pump in a particular vehicle. A 1999 Citroën pocket guide reproduction identifies one TUD5 VJZ example with Lucas DPC R8444 B/662C. Read the physical pump identification and match the service procedure.

1.9 XUD turbo diesel: Bosch pump

An owner tutorial for a Peugeot 405 with a 1.9 XUD9/TE and Bosch pump discusses the boost-responsive diaphragm and LDA cone, fuel delivery and turbo pressure; a Lucas-equipped 306 is mentioned separately. 405 owner tutorial. These are individual community claims: the adjustments, quoted pressure limits and performance assertions are not independently verified and do not establish safe settings or apply to Lucas pumps.

Before any pump or boost changes, document the original configuration and service condition, including fuel and intake leaks, cooling, actuator operation and actual boost. A pump specialist can verify timing and delivery against the exact pump specification. Record smoke and temperature under comparable load; visible smoke or a perceived gain alone does not validate fuelling, exhaust temperature or reliability. Keep applicable emissions equipment operational.

Lucas-to-Bosch pump conversions

Owner reports of Lucas-to-Bosch conversions on the 306 DHY and of a 306 XUD9TD swap treat the pump together with its pulley, mount, matching injectors, high-pressure lines, fuel connections and stop control. Owners differ on mounting details, and some Bosch pumps have electronic advance control. 306 DHY Lucas-to-Bosch conversion; 306 XUD9TD swap. These are planning leads, not a universal parts list: match the exact donor pump and vehicle, timing and controls before a conversion, and check the applicable emissions requirements. The XUD service reference specifically notes a different high-pressure pipe set for the XUD9BTF VP20 needle-lift injector, illustrating why a familiar-looking pipe set is not enough to establish compatibility.

One 306 Bosch-conversion owner report describes rough running and smoke after a pump swap, with air observed in the fuel supply. No verified cause is established; inspect the low-pressure fuel supply, leaks and priming as well as timing and the condition of the replacement pump before interpreting the behaviour as a fuelling adjustment problem. 306 Bosch-conversion troubleshooting.

How boost compensation affects fuelling

Bosch's distributor-pump technical instruction, pages 37–39, explains an LDA pressure compensator: charge pressure acts on a spring-loaded diaphragm and tapered control pin, whose follower changes the full-load fuel limit. At lower boost the mechanism restricts full-load delivery; spring preload influences when the diaphragm responds, while the cone and follower govern how movement changes the limit. The LDA affects the pressure-dependent fuel curve, not simply a fixed increase in fuel everywhere.

A 306 Owners Club LDA discussion illustrates these components and owner-proposed modifications. Pin profiles, spring characteristics and pump calibration differ; the alterations and suggested figures there have not been validated as general settings. Before considering a change, check the pressure-signal hose, diaphragm and linkage, and confirm actual boost; a damaged signal path can leave fuel restricted despite boost at the engine. Check response at low, intermediate and higher boost with the pump's own test data rather than judging the curve from a single smoke observation.

Owner-reported XUD build results

Owner-reported rolling-road results for XUD builds show a wide spread. A 306 Owners Club rolling-road results collection lists, for example, a T2/9 mm pump build at 124 bhp and 204 lb-ft and another 9 mm/front-mount-intercooler build at 133 bhp and 228.6 lb-ft. Other listings change the turbo, pump internals or supplementary systems, and some dyno and rpm readings are questioned. In the same collection, one build with a GT15, 11 mm pump, front-mount intercooler and homemade LDA pin is reported at 153 bhp and 286 lb-ft, and a TD04, 11 mm pump, front-mount intercooler and homemade LDA pin at 179 bhp and 250 lb-ft, each said to be an average of three runs on the same named rolling road. Peak-torque rpm, measurement basis and all intervening changes are not established. These are reports rather than controlled comparisons or predicted gains; preserve the full build specification and test conditions when comparing them.

In an XUD7TE pump build, a Bosch 0 460 484 038 is identified as an 8 mm pump with coolant-controlled cold-start features, and a proposed 9 mm donor plunger is reported not to have fitted the original camplate. These are observations about that build, not a validated parts-compatibility table. A diesel specialist's catalogue independently describes that number as VE4/8F2150R403 and lists selected BX 17 turbo and 405 1.8 turbo applications. This corroborates the identification, not interchangeability of modified parts. Head diameter alone does not establish camplate, drive, governor, cold-start or injector compatibility; identify the actual components and have a specialist verify and calibrate the assembled pump.

XUD9TE variable-geometry build example

A 306 XUD9TE D8B project combines a GT2052SV variable-geometry turbo, a custom mapped controller, a modified 11 mm Bosch VE pump and standard injector nozzles. Instrumentation included boost, exhaust-manifold pressure and exhaust-gas temperature. The controller is described as intermittent, which matters when interpreting the build: fitting a VNT to a mechanical-pump engine also requires a suitable vane-control strategy, not merely a fuel-pump change.

The owner reports 154 hp at the wheels and estimates about 175 hp at the flywheel using an assumed transmission loss. Both are an owner's report; a calculated crank figure depends on the loss method and is not an independent measurement. The same owner reports coolant pressurisation, overheating and limited clutch life. Those symptoms and the heavily modified, aged engine do not establish a universal safe or failure threshold.

A separate Peugeot 206 DW8-to-XUD9TE swap and VNT build began as an initially smoky, laggy GT22 setup that exceeded the range of a 30 psi boost gauge. The owner attributed the first episode to actuator direction and a later recurrence to a boost-controller spring; these are owner diagnoses, with several modifications over the project. The build later lists boost, exhaust-gas-temperature and exhaust-manifold-pressure gauges, and a change from an 11 mm to a 10 mm Bosch pump. Check vane movement, actuator direction and the control system, and measure the actual installation; the reported pressures and pump changes are not settings to copy. This was an engine swap, not evidence that the 206 originally carried an XUD9TE.

Static timing is pump-specific

A period XUD service reference lists XUD9 TF/L D8B with Bosch XUD 212 R 513 and a static TDC pump-lift value of 0.66 mm; its XUD9 BTF/L3 DHX Bosch VP20 XUD BP 02 601 example lists 0.57 mm. These are different factory service examples, not performance-tuning targets. Pump piston travel in millimetres is not crankshaft advance in degrees. Use the exact pump, reference position and measuring method from the applicable service documentation, and check timing with the specified equipment.

For that D8B Bosch XUD 212 R 513 example, the period workshop reference additionally lists an indicative dynamic check of 11° ± 1° at 800 rpm, measured on the injection-pump side. It says to check static pump timing if the dynamic value is out of tolerance. This is a pump-specific diagnostic reference, not a tuning target or a direct conversion of the static lift into crankshaft degrees; follow the specified measurement method.

The same reference distinguishes a thermostatic cable-operated fast idle on its XUD9TF example from pneumatic fast-idle actuation on its XUD9BTF. On a cold-running complaint, identify which system is fitted and check its operation before attributing the symptom to the pump's internal calibration.

The same reference identifies the DHX VP20 as semi-electronic, with a load potentiometer, advance solenoid and needle-lift feedback; it separately describes the D8B mechanical pump. Similar Bosch hardware does not imply identical timing control or interchangeable adjustments.

Citroën's VP20 AS3.1 training reproduction adds detail for the documented XUD9BTF: the ECU uses pump load-lever position, engine speed, coolant temperature and needle-lift feedback from injector No. 3 to control its advance solenoid. It describes a pump-mounted boost-dependent fuel limiter and a separate ECU atmospheric-pressure altitude correction; these are different pressure inputs. During deceleration fuel cut, it says needle-lift feedback disappears and advance operates open loop. Check the operating state and the exact system when comparing timing signals; ECU presence alone does not make its control strategy equivalent to EPIC or VP36.

Bosch's VE technical instruction also describes the internal vane supply pump and pressure-control valve establishing speed-dependent housing pressure, which acts on a hydraulic timing piston and changes running advance. The specified overflow restriction or valve supports housing-pressure regulation and returns fuel for cooling and self-venting. Correct static lift alone therefore does not verify running advance: check fuel supply, air ingress and the advance mechanism using the exact-pump procedure. Housing pressure is not high-pressure injector-line pressure; do not obstruct the return as a tuning shortcut.

Bosch's VE instruction distinguishes the pump's start of delivery from the injector's later opening: a pressure wave travels through the high-pressure line before the nozzle opens. The elapsed time translates into a larger crank-angle difference as engine speed rises, and line length also matters. Thus static pump lift, pump delivery timing and needle-lift-based start of injection are different measurements and should not be compared as though they were the same number.

On VE variants equipped with load-dependent start-of-delivery control, Bosch describes a separate load-related timing effect, distinct from the LDA's boost-dependent fuel limit. Establish whether the actual pump has this feature before attributing a part-load timing change to it. A Peugeot 405 Bosch service reference says its XUD7TE procedure temporarily releases the cold-start control during static pump timing and reconnects it afterward. This is specific to that procedure; verify the correct cold-start state for the actual pump.

Lucas mechanical pumps

An owner report on a 306 turbo diesel with a Lucas pump describes little visible smoke during acceleration through the gears but heavy smoke at low speed in a high gear after changes. 306 Lucas pump discussion. That observation is anecdotal and does not validate the suggested settings or establish the cause. It illustrates why comparable load and operating conditions matter: no visible smoke in one test is not proof that fuelling is correct across the full operating range.

A diesel fuel-system reference describes a Lucas DPC turbo-compensator design in which boost acts on diaphragms and alters hydraulic pressure acting on an excess-fuel carriage; an inclined profile makes the increase in maximum delivery progressive. This is a general DPC design example, not evidence that every Lucas-equipped PSA has the same actuator or adjustment. It helps explain why Bosch VE LDA instructions cannot simply be copied to a Lucas pump.

Failure of the Lucas boost-compensator signal path is documented in owner reports: diesel found at the pressure connection with diaphragm failure suspected, and oil filling a similar signal hose. Citroën BX TZD discussion. These are different owner observations, not proof of the cause in another vehicle. A diesel pump specialist lists distinct early and late DPC diaphragm parts. Investigate a leaking or obstructed pressure signal and identify the actual pump; an active fuel leak or fuel entering the intake requires repair before further running.

A Lucas Roto-Diesel timing worksheet describes dial-indicator measurement of pump-plunger lift against engine position and identifies two alternative procedures depending on engine type. Select the vehicle's exact Lucas pump reference, method and specification; do not assume the Bosch measurement procedure, reference position or numerical lift applies.

A pump specialist's DPC application index lists, for example, 8443B453D against Citroën BX 1.7 TD / Peugeot 405 and XUD7TE, and 8443B744B against Citroën XM 2.1 Turbo D XUD11ATE. It is a supplier catalogue lead, not a complete interchangeability list. Match the full pump plate and exact service data before ordering parts or calibrating.

A Partner XUD Lucas service reference says the individual static-timing value for its described pump may be shown on a pump disc or control-lever tag, to be read with the specified indicator and adapter. This is a service-setting identification lead for that procedure, not proof every Lucas pump carries the same tag or uses the same reference position.

For the Saxo 1.5D TUD5 VJZ Lucas DPC, the 1999 Citroën pocket guide describes timing by locating the flywheel, camshaft pulley and pump plate with their specified pins. Its VJZ table describes the initial advance as non-adjustable. This differs from the indicator-based Partner procedure above; identify the precise engine and pump before selecting a method. The same VJZ guide calls for checking that the cold fast-idle cable holds its lever against the stop and is slack when warm, and, with the engine stopped, that the accelerator lever reaches both its full-load and idle stops. Cable or thermostatic-control faults can complicate a pump diagnosis, so establish their condition before changing fuelling.

1.9 DW8B: mechanical pump with electronic timing control

A French vocational diesel examination technical dossier describes a DW8B Lucas DCN2 mechanically driven pump with electronic management. The controller handles functions including injection advance, EGR and pre/post-heating. The load potentiometer is on the pump and the No. 1 injector carries a needle-lift sensor. A separate DW8 service workbook reproduction describes the needle-lift signal as start-of-injection feedback to the diesel control unit. These are distinct from a common-rail pressure control system.

A Peugeot DW8 technical review describes the DW8B advance solenoid as duty-cycle controlled: in its explanation, closing the valve reduces leakage and allows transfer pressure to move the piston toward more advance; opening it reduces piston pressure and permits the return spring to move it toward less advance. The documented valve has an ignition-switched feed and ECU ground control. Check the exact circuit and operating conditions; a multimeter's average voltage is not a direct measurement of injection advance.

Owner reports show how advance faults are misread. A Partner 1.9D owner found that retarding the pump suppressed a warning but produced difficult starting, poor idle and black smoke, together with a mismatch between requested and measured advance. Partner 1.9D advance-fault discussion. This is an unresolved owner account, not a validated repair or reference value; compare specified mechanical timing and requested versus measured advance under documented conditions rather than treating the warning lamp alone as proof of correct timing.

For a timing or running fault, use the relevant vehicle-specific diagnostic and service procedure to assess the load signal, injector feedback, wiring and commanded advance alongside mechanical timing and fuel supply. An ECU in the system does not prove the pump has a conventional common-rail tune or that an HDi definition can be applied.

A 2006 Berlingo DW8B owner compared Lexia timing readings while investigating sluggishness and explicitly lacked a reference value. Berlingo DW8B discussion. The readings and explanations there are not confirmed specifications. Record coolant temperature, speed, load and diagnostic state, and use the correct vehicle and pump documentation for any comparison.

Electronically managed XUD and DK5

The XM examples above distinguish Lucas EPIC and Bosch VP36 systems. Record the pump and controller identities, vehicle configuration, fault codes and current service procedures before deciding whether electronic programming, mechanical repair or specialist pump work is relevant. Do not infer map locations, flash access or wiring from a similar-displacement engine.

XUD11BTE Lucas EPIC

Citroën's XUD11BTE EPIC training reproduction describes ECU-controlled pump metering and advance, a cable-operated accelerator position sensor with a plausibility switch, and inlet pressure and air-temperature inputs. In the documented system the No. 4 injector has needle-lift feedback for measured start of injection and dynamic advance correction. The manufacturer describes the sensor/injector assembly as factory adjusted and prohibits resetting that injector; consult the exact current service procedure. This numbering is specific to the documented system and differs from the DW8B example above.

For one XM P8C XUD11BTE/L3 example, the Citroën XM technical documentation lists holder LCR6734302H for cylinders 1–3 and the needle-lift holder LDC002R01AD3 for cylinder 4. Both are listed at 150 ± 5 bar opening pressure in that particular factory application. This is an injector service reference, not a common-rail pressure or an upgraded tuning target; identify the actual injectors and retain the documented prohibition on resetting the sensor-equipped holder.

In the same EPIC training, two separate metering solenoids regulate fuel-cavity volume and shift the rotor; rotor-position feedback closes the delivery loop. A separate advance solenoid and cam-position sensor control timing, with needle-lift information providing dynamic correction. The diagnostic parameter called rotor decoding is described in microseconds of sensor current build-up, not directly as injected milligrams per stroke. Compare the actual parameter and units between diagnostic tools before interpreting logs.

A Lucas Peugeot/Citroën EPIC after-sales guide reproduction documents Laser 2000 live-data names for its XUD11BTE/L3 system. DEBIT PEDALE is the driver fuel demand calculated from pedal position and rpm; DEBIT MAXIMUM is the operating-condition/map-derived limit, while DEBIT MAX TRANS is a temporary acceleration limit that may exceed it. DEBIT ACTUEL is the corrected pump request; DEBIT BRUT is a more stable average before those corrections. These are distinct calculated quantities, not independently measured injector delivery.

The guide distinguishes requested and measured rotor and cam position, as well as CONS AVANCE DYN (requested dynamic advance) and POS AVANCE DYN (measured from engine speed and needle-lift signals). It describes rotor decoding in microseconds and manifold pressure as absolute. Its rotor-position scale can change between cranking and running, so interpret a jump across that state transition cautiously. Labels, units and sample behaviour can differ on other tools: confirm them before comparing logs or drawing tuning conclusions.

The Lucas EPIC after-sales guide says its absolute manifold-pressure reading should equal local atmospheric pressure before starting. Compare any running reading with a pressure gauge in matching absolute or gauge units. It describes DELAI EV DEBIT + and DELAI EV DEBIT - as adaptive solenoid response delays affected by engine speed, pressure and air passing through the pump. For this diagnostic implementation they are generally below 5 ms; a value that remains above 7 ms indicates an anomaly. These are diagnostic observations for the documented system, not fuel-map settings; confirm the tool's label, units and operating state.

For the documented XUD11BTE/L3 system, the Lucas after-sales guide defines COR. CALAGE POMPE as the correction used to achieve dynamic advance and gives a diagnostic reference of -1.5° to +1.5° at 3,000 rpm with the engine warm and unloaded. This is a conditional service check, not an advance target for tuning. Compare the exact parameter, operating conditions and applicable current service procedure; a correction value alone does not prove the static pump timing is correct.

Citroën's XUD11BTE training notes that rotor- or cam-position faults can be recorded following fuel-filter replacement while the pump self-degasses. Its procedure calls for clearing those faults after the engine has run. Record existing fault history and symptoms first, and investigate any recurring fault; this note does not explain every rotor or cam code.

The EPIC after-sales guide lists different fallback actions for different fault codes. For example, an accelerator-position plausibility fault can restrict fuel demand, while some other faults use substitute sensor values or reduced delivery. Record current and historical codes, operating conditions and live data before clearing them; a power loss may reflect a specific fallback strategy rather than a calibration limit.

Citroën describes an individually selected pump calibration resistor that reports internal pump characteristics to the ECU, and a coolant-temperature protection that can limit fuelling. A resistor substitution is not a validated tuning method; investigate hot-load power reduction alongside temperature, sensor readings and fault state. These details apply to the documented XUD11BTE EPIC configuration.

As a specific identification lead, the Citroën XM 1996 documentation reproduction associates the P8C XUD11BTE L/L3 with Lucas EPIC XUDLC01 and controller reference R04010011B. Match the actual ECU, software, emissions specification and transmission; the reference does not establish that other 2.1 files or EPROMs are interchangeable.

The XM model-year 2000 technical material gives further XUD11BTE/L3 EPIC examples: manual gearbox, PSA ECU 9630509280, supplier R04010020B, software 41502211; automatic, PSA 9631445980, supplier R04010015E, software 41501411. Record the transmission and emissions variant as well as the actual ECU and software numbers when researching files. These catalogue examples do not establish interchangeability.

Owner reports on EPIC repairs and chip work are unverified. A Peugeot 406 2.1 EPIC case describes unstable idle after rotor-sensor work on a pump that was not bench-tested, with calibration need discussed; the reported temporary improvement and suggested remedy are unverified. Inspect fault data and arrange pump-specific testing rather than assuming a sensor swap or shim change fixes another pump.

A Xantia 2.1 TD EPROM installation illustrates electronic calibration work on a Lucas ECU. Different keypad-code outcomes are reported on two vehicles, with uncertainty about another immobiliser configuration. More acceleration smoke is also reported with an EPROM called "V6" than with "V3"; these are chip-revision labels, not engine cylinder counts. The observations are subjective, with no disclosed matched software IDs or controlled air and fuel data. This is not a verified file or interchangeability guide: identify the ECU and memory, preserve a verified original, and understand vehicle-specific coding and recovery before any work.

DK5 2.5 Turbo D Bosch VP36

The Citroën EDC 1.2.8 training reproduction specifically describes the XM DK5 ATE/L3 VP36 pump with MSA11 7.6: the ECU commands metering and advance, receives pump fuel-slide position feedback, and uses engine-speed and needle-lift signals for injection timing. Its illustrated sensor injector is No. 3; the document warns against adjusting that injector because disassembly can damage its sensor. Diagnose the actual control and feedback signals against vehicle-specific service information; mechanical VE LDA instructions do not define this system.

In the documented DK5 VP36 system, the Citroën training identifies separate influences on commanded fuel: driver demand, an air/smoke limit using engine speed, intake pressure and intake-air temperature, an engine-speed-dependent full-load torque limit, overheating protection, fuel-temperature correction and starting enrichment. It also describes closed-loop injection timing using needle-lift feedback and transient fuel shaping to reduce driveline jerk. Log operating state, requested and available signals and temperatures when diagnosing a limit; these functional descriptions do not identify ROM addresses or establish maps for another ECU.

Citroën's 1996 XM documentation reproduction lists Bosch controller 0281001336 for the DK5ATE L3 MSA11 7.6 example. A separate historical tuner ECU list associates that controller number with chip-number entries 2287358818 / 27C256 and 2237355488 / 87C257. The list is an unverified identification lead: it does not establish whether the entries are alternative calibrations or separate devices in one controller, nor does it prove file compatibility, checksum rules or an access method. Identify the physical devices and preserve the actual reads before modification.

The same document describes limited ELIT after-sales coding of parameters including idle, full-load delivery and starting quantity, intended only when necessary. These service adjustments are not evidence of a general tuning method, a safe power increase, or the ability to read or rewrite the ECU's calibration. Establish the exact tool function, original settings and documented recovery procedure before changing any coding.

For later common-rail vehicles see the PSA HDi and BlueHDi diesel tuning guide and Boxer and Relay diesel guide. The PSA ECU identification overview links related petrol and diesel material.

For which pump and injector family is listed against each engine code, from XUD to HDi, see Peugeot and Citroën diesel injection pumps and injectors by engine code. Rail-pressure limits, injector upgrades and coding on common-rail engines are covered in the Peugeot HDi injector and high-pressure pump tuning guide.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 9: Peugeot and Citroen rotary pump diesel tuning guide

Older Peugeot and Citroën diesels include mechanical injection pumps and electronically managed rotary-pump systems. Identify the engine code, exact pump maker and part number, ECU where fitted, vehicle and emissions equipment before choosing service information or considering tuning. These systems do not all use the same controls and cannot be treated as interchangeable with common-rail HDi.

Identify the injection system first

Citroën's XM technical summary lists three distinct examples: the 2.1 Turbo D XUD11 ATE/L with a mechanical pump; XUD11 BTE/L with Lucas Diesel EPIC electronic injection; and 2.5 Turbo D DK5 ATE/L3 with Bosch MSA 11 7.6 and VP36 electronic injection. The document concerns specific multiplexed XM versions and model years; it is not an all-market year cutoff or proof that every XUD pump is mechanical.

Snap-on's 2013 vehicle-communication manual lists both Lucas and Bosch VP20 equipment for the 1.9 turbo diesel DHX in selected Xantia, Evasion, Jumpy, 406, 806 and Expert examples, and lists Lucas or Bosch VP20 for Citroën Saxo 1.5 VJY/VJZ. It is a diagnostic selection guide, not proof of the pump in a particular vehicle. A 1999 Citroën pocket guide reproduction identifies one TUD5 VJZ example with Lucas DPC R8444 B/662C. Read the physical pump identification and match the service procedure.

1.9 XUD turbo diesel: Bosch pump

An owner tutorial for a Peugeot 405 with a 1.9 XUD9/TE and Bosch pump discusses the boost-responsive diaphragm and LDA cone, fuel delivery and turbo pressure; a Lucas-equipped 306 is mentioned separately. 405 owner tutorial. These are individual community claims: the adjustments, quoted pressure limits and performance assertions are not independently verified and do not establish safe settings or apply to Lucas pumps.

Before any pump or boost changes, document the original configuration and service condition, including fuel and intake leaks, cooling, actuator operation and actual boost. A pump specialist can verify timing and delivery against the exact pump specification. Record smoke and temperature under comparable load; visible smoke or a perceived gain alone does not validate fuelling, exhaust temperature or reliability. Keep applicable emissions equipment operational.

Lucas-to-Bosch pump conversions

Owner reports of Lucas-to-Bosch conversions on the 306 DHY and of a 306 XUD9TD swap treat the pump together with its pulley, mount, matching injectors, high-pressure lines, fuel connections and stop control. Owners differ on mounting details, and some Bosch pumps have electronic advance control. 306 DHY Lucas-to-Bosch conversion; 306 XUD9TD swap. These are planning leads, not a universal parts list: match the exact donor pump and vehicle, timing and controls before a conversion, and check the applicable emissions requirements. The XUD service reference specifically notes a different high-pressure pipe set for the XUD9BTF VP20 needle-lift injector, illustrating why a familiar-looking pipe set is not enough to establish compatibility.

One 306 Bosch-conversion owner report describes rough running and smoke after a pump swap, with air observed in the fuel supply. No verified cause is established; inspect the low-pressure fuel supply, leaks and priming as well as timing and the condition of the replacement pump before interpreting the behaviour as a fuelling adjustment problem. 306 Bosch-conversion troubleshooting.

How boost compensation affects fuelling

Bosch's distributor-pump technical instruction, pages 37–39, explains an LDA pressure compensator: charge pressure acts on a spring-loaded diaphragm and tapered control pin, whose follower changes the full-load fuel limit. At lower boost the mechanism restricts full-load delivery; spring preload influences when the diaphragm responds, while the cone and follower govern how movement changes the limit. The LDA affects the pressure-dependent fuel curve, not simply a fixed increase in fuel everywhere.

A 306 Owners Club LDA discussion illustrates these components and owner-proposed modifications. Pin profiles, spring characteristics and pump calibration differ; the alterations and suggested figures there have not been validated as general settings. Before considering a change, check the pressure-signal hose, diaphragm and linkage, and confirm actual boost; a damaged signal path can leave fuel restricted despite boost at the engine. Check response at low, intermediate and higher boost with the pump's own test data rather than judging the curve from a single smoke observation.

Owner-reported XUD build results

Owner-reported rolling-road results for XUD builds show a wide spread. A 306 Owners Club rolling-road results collection lists, for example, a T2/9 mm pump build at 124 bhp and 204 lb-ft and another 9 mm/front-mount-intercooler build at 133 bhp and 228.6 lb-ft. Other listings change the turbo, pump internals or supplementary systems, and some dyno and rpm readings are questioned. In the same collection, one build with a GT15, 11 mm pump, front-mount intercooler and homemade LDA pin is reported at 153 bhp and 286 lb-ft, and a TD04, 11 mm pump, front-mount intercooler and homemade LDA pin at 179 bhp and 250 lb-ft, each said to be an average of three runs on the same named rolling road. Peak-torque rpm, measurement basis and all intervening changes are not established. These are reports rather than controlled comparisons or predicted gains; preserve the full build specification and test conditions when comparing them.

In an XUD7TE pump build, a Bosch 0 460 484 038 is identified as an 8 mm pump with coolant-controlled cold-start features, and a proposed 9 mm donor plunger is reported not to have fitted the original camplate. These are observations about that build, not a validated parts-compatibility table. A diesel specialist's catalogue independently describes that number as VE4/8F2150R403 and lists selected BX 17 turbo and 405 1.8 turbo applications. This corroborates the identification, not interchangeability of modified parts. Head diameter alone does not establish camplate, drive, governor, cold-start or injector compatibility; identify the actual components and have a specialist verify and calibrate the assembled pump.

XUD9TE variable-geometry build example

A 306 XUD9TE D8B project combines a GT2052SV variable-geometry turbo, a custom mapped controller, a modified 11 mm Bosch VE pump and standard injector nozzles. Instrumentation included boost, exhaust-manifold pressure and exhaust-gas temperature. The controller is described as intermittent, which matters when interpreting the build: fitting a VNT to a mechanical-pump engine also requires a suitable vane-control strategy, not merely a fuel-pump change.

The owner reports 154 hp at the wheels and estimates about 175 hp at the flywheel using an assumed transmission loss. Both are an owner's report; a calculated crank figure depends on the loss method and is not an independent measurement. The same owner reports coolant pressurisation, overheating and limited clutch life. Those symptoms and the heavily modified, aged engine do not establish a universal safe or failure threshold.

A separate Peugeot 206 DW8-to-XUD9TE swap and VNT build began as an initially smoky, laggy GT22 setup that exceeded the range of a 30 psi boost gauge. The owner attributed the first episode to actuator direction and a later recurrence to a boost-controller spring; these are owner diagnoses, with several modifications over the project. The build later lists boost, exhaust-gas-temperature and exhaust-manifold-pressure gauges, and a change from an 11 mm to a 10 mm Bosch pump. Check vane movement, actuator direction and the control system, and measure the actual installation; the reported pressures and pump changes are not settings to copy. This was an engine swap, not evidence that the 206 originally carried an XUD9TE.

Static timing is pump-specific

A period XUD service reference lists XUD9 TF/L D8B with Bosch XUD 212 R 513 and a static TDC pump-lift value of 0.66 mm; its XUD9 BTF/L3 DHX Bosch VP20 XUD BP 02 601 example lists 0.57 mm. These are different factory service examples, not performance-tuning targets. Pump piston travel in millimetres is not crankshaft advance in degrees. Use the exact pump, reference position and measuring method from the applicable service documentation, and check timing with the specified equipment.

For that D8B Bosch XUD 212 R 513 example, the period workshop reference additionally lists an indicative dynamic check of 11° ± 1° at 800 rpm, measured on the injection-pump side. It says to check static pump timing if the dynamic value is out of tolerance. This is a pump-specific diagnostic reference, not a tuning target or a direct conversion of the static lift into crankshaft degrees; follow the specified measurement method.

The same reference distinguishes a thermostatic cable-operated fast idle on its XUD9TF example from pneumatic fast-idle actuation on its XUD9BTF. On a cold-running complaint, identify which system is fitted and check its operation before attributing the symptom to the pump's internal calibration.

The same reference identifies the DHX VP20 as semi-electronic, with a load potentiometer, advance solenoid and needle-lift feedback; it separately describes the D8B mechanical pump. Similar Bosch hardware does not imply identical timing control or interchangeable adjustments.

Citroën's VP20 AS3.1 training reproduction adds detail for the documented XUD9BTF: the ECU uses pump load-lever position, engine speed, coolant temperature and needle-lift feedback from injector No. 3 to control its advance solenoid. It describes a pump-mounted boost-dependent fuel limiter and a separate ECU atmospheric-pressure altitude correction; these are different pressure inputs. During deceleration fuel cut, it says needle-lift feedback disappears and advance operates open loop. Check the operating state and the exact system when comparing timing signals; ECU presence alone does not make its control strategy equivalent to EPIC or VP36.

Bosch's VE technical instruction also describes the internal vane supply pump and pressure-control valve establishing speed-dependent housing pressure, which acts on a hydraulic timing piston and changes running advance. The specified overflow restriction or valve supports housing-pressure regulation and returns fuel for cooling and self-venting. Correct static lift alone therefore does not verify running advance: check fuel supply, air ingress and the advance mechanism using the exact-pump procedure. Housing pressure is not high-pressure injector-line pressure; do not obstruct the return as a tuning shortcut.

Bosch's VE instruction distinguishes the pump's start of delivery from the injector's later opening: a pressure wave travels through the high-pressure line before the nozzle opens. The elapsed time translates into a larger crank-angle difference as engine speed rises, and line length also matters. Thus static pump lift, pump delivery timing and needle-lift-based start of injection are different measurements and should not be compared as though they were the same number.

On VE variants equipped with load-dependent start-of-delivery control, Bosch describes a separate load-related timing effect, distinct from the LDA's boost-dependent fuel limit. Establish whether the actual pump has this feature before attributing a part-load timing change to it. A Peugeot 405 Bosch service reference says its XUD7TE procedure temporarily releases the cold-start control during static pump timing and reconnects it afterward. This is specific to that procedure; verify the correct cold-start state for the actual pump.

Lucas mechanical pumps

An owner report on a 306 turbo diesel with a Lucas pump describes little visible smoke during acceleration through the gears but heavy smoke at low speed in a high gear after changes. 306 Lucas pump discussion. That observation is anecdotal and does not validate the suggested settings or establish the cause. It illustrates why comparable load and operating conditions matter: no visible smoke in one test is not proof that fuelling is correct across the full operating range.

A diesel fuel-system reference describes a Lucas DPC turbo-compensator design in which boost acts on diaphragms and alters hydraulic pressure acting on an excess-fuel carriage; an inclined profile makes the increase in maximum delivery progressive. This is a general DPC design example, not evidence that every Lucas-equipped PSA has the same actuator or adjustment. It helps explain why Bosch VE LDA instructions cannot simply be copied to a Lucas pump.

Failure of the Lucas boost-compensator signal path is documented in owner reports: diesel found at the pressure connection with diaphragm failure suspected, and oil filling a similar signal hose. Citroën BX TZD discussion. These are different owner observations, not proof of the cause in another vehicle. A diesel pump specialist lists distinct early and late DPC diaphragm parts. Investigate a leaking or obstructed pressure signal and identify the actual pump; an active fuel leak or fuel entering the intake requires repair before further running.

A Lucas Roto-Diesel timing worksheet describes dial-indicator measurement of pump-plunger lift against engine position and identifies two alternative procedures depending on engine type. Select the vehicle's exact Lucas pump reference, method and specification; do not assume the Bosch measurement procedure, reference position or numerical lift applies.

A pump specialist's DPC application index lists, for example, 8443B453D against Citroën BX 1.7 TD / Peugeot 405 and XUD7TE, and 8443B744B against Citroën XM 2.1 Turbo D XUD11ATE. It is a supplier catalogue lead, not a complete interchangeability list. Match the full pump plate and exact service data before ordering parts or calibrating.

A Partner XUD Lucas service reference says the individual static-timing value for its described pump may be shown on a pump disc or control-lever tag, to be read with the specified indicator and adapter. This is a service-setting identification lead for that procedure, not proof every Lucas pump carries the same tag or uses the same reference position.

For the Saxo 1.5D TUD5 VJZ Lucas DPC, the 1999 Citroën pocket guide describes timing by locating the flywheel, camshaft pulley and pump plate with their specified pins. Its VJZ table describes the initial advance as non-adjustable. This differs from the indicator-based Partner procedure above; identify the precise engine and pump before selecting a method. The same VJZ guide calls for checking that the cold fast-idle cable holds its lever against the stop and is slack when warm, and, with the engine stopped, that the accelerator lever reaches both its full-load and idle stops. Cable or thermostatic-control faults can complicate a pump diagnosis, so establish their condition before changing fuelling.

1.9 DW8B: mechanical pump with electronic timing control

A French vocational diesel examination technical dossier describes a DW8B Lucas DCN2 mechanically driven pump with electronic management. The controller handles functions including injection advance, EGR and pre/post-heating. The load potentiometer is on the pump and the No. 1 injector carries a needle-lift sensor. A separate DW8 service workbook reproduction describes the needle-lift signal as start-of-injection feedback to the diesel control unit. These are distinct from a common-rail pressure control system.

A Peugeot DW8 technical review describes the DW8B advance solenoid as duty-cycle controlled: in its explanation, closing the valve reduces leakage and allows transfer pressure to move the piston toward more advance; opening it reduces piston pressure and permits the return spring to move it toward less advance. The documented valve has an ignition-switched feed and ECU ground control. Check the exact circuit and operating conditions; a multimeter's average voltage is not a direct measurement of injection advance.

Owner reports show how advance faults are misread. A Partner 1.9D owner found that retarding the pump suppressed a warning but produced difficult starting, poor idle and black smoke, together with a mismatch between requested and measured advance. Partner 1.9D advance-fault discussion. This is an unresolved owner account, not a validated repair or reference value; compare specified mechanical timing and requested versus measured advance under documented conditions rather than treating the warning lamp alone as proof of correct timing.

For a timing or running fault, use the relevant vehicle-specific diagnostic and service procedure to assess the load signal, injector feedback, wiring and commanded advance alongside mechanical timing and fuel supply. An ECU in the system does not prove the pump has a conventional common-rail tune or that an HDi definition can be applied.

A 2006 Berlingo DW8B owner compared Lexia timing readings while investigating sluggishness and explicitly lacked a reference value. Berlingo DW8B discussion. The readings and explanations there are not confirmed specifications. Record coolant temperature, speed, load and diagnostic state, and use the correct vehicle and pump documentation for any comparison.

Electronically managed XUD and DK5

The XM examples above distinguish Lucas EPIC and Bosch VP36 systems. Record the pump and controller identities, vehicle configuration, fault codes and current service procedures before deciding whether electronic programming, mechanical repair or specialist pump work is relevant. Do not infer map locations, flash access or wiring from a similar-displacement engine.

XUD11BTE Lucas EPIC

Citroën's XUD11BTE EPIC training reproduction describes ECU-controlled pump metering and advance, a cable-operated accelerator position sensor with a plausibility switch, and inlet pressure and air-temperature inputs. In the documented system the No. 4 injector has needle-lift feedback for measured start of injection and dynamic advance correction. The manufacturer describes the sensor/injector assembly as factory adjusted and prohibits resetting that injector; consult the exact current service procedure. This numbering is specific to the documented system and differs from the DW8B example above.

For one XM P8C XUD11BTE/L3 example, the Citroën XM technical documentation lists holder LCR6734302H for cylinders 1–3 and the needle-lift holder LDC002R01AD3 for cylinder 4. Both are listed at 150 ± 5 bar opening pressure in that particular factory application. This is an injector service reference, not a common-rail pressure or an upgraded tuning target; identify the actual injectors and retain the documented prohibition on resetting the sensor-equipped holder.

In the same EPIC training, two separate metering solenoids regulate fuel-cavity volume and shift the rotor; rotor-position feedback closes the delivery loop. A separate advance solenoid and cam-position sensor control timing, with needle-lift information providing dynamic correction. The diagnostic parameter called rotor decoding is described in microseconds of sensor current build-up, not directly as injected milligrams per stroke. Compare the actual parameter and units between diagnostic tools before interpreting logs.

A Lucas Peugeot/Citroën EPIC after-sales guide reproduction documents Laser 2000 live-data names for its XUD11BTE/L3 system. DEBIT PEDALE is the driver fuel demand calculated from pedal position and rpm; DEBIT MAXIMUM is the operating-condition/map-derived limit, while DEBIT MAX TRANS is a temporary acceleration limit that may exceed it. DEBIT ACTUEL is the corrected pump request; DEBIT BRUT is a more stable average before those corrections. These are distinct calculated quantities, not independently measured injector delivery.

The guide distinguishes requested and measured rotor and cam position, as well as CONS AVANCE DYN (requested dynamic advance) and POS AVANCE DYN (measured from engine speed and needle-lift signals). It describes rotor decoding in microseconds and manifold pressure as absolute. Its rotor-position scale can change between cranking and running, so interpret a jump across that state transition cautiously. Labels, units and sample behaviour can differ on other tools: confirm them before comparing logs or drawing tuning conclusions.

The Lucas EPIC after-sales guide says its absolute manifold-pressure reading should equal local atmospheric pressure before starting. Compare any running reading with a pressure gauge in matching absolute or gauge units. It describes DELAI EV DEBIT + and DELAI EV DEBIT - as adaptive solenoid response delays affected by engine speed, pressure and air passing through the pump. For this diagnostic implementation they are generally below 5 ms; a value that remains above 7 ms indicates an anomaly. These are diagnostic observations for the documented system, not fuel-map settings; confirm the tool's label, units and operating state.

For the documented XUD11BTE/L3 system, the Lucas after-sales guide defines COR. CALAGE POMPE as the correction used to achieve dynamic advance and gives a diagnostic reference of -1.5° to +1.5° at 3,000 rpm with the engine warm and unloaded. This is a conditional service check, not an advance target for tuning. Compare the exact parameter, operating conditions and applicable current service procedure; a correction value alone does not prove the static pump timing is correct.

Citroën's XUD11BTE training notes that rotor- or cam-position faults can be recorded following fuel-filter replacement while the pump self-degasses. Its procedure calls for clearing those faults after the engine has run. Record existing fault history and symptoms first, and investigate any recurring fault; this note does not explain every rotor or cam code.

The EPIC after-sales guide lists different fallback actions for different fault codes. For example, an accelerator-position plausibility fault can restrict fuel demand, while some other faults use substitute sensor values or reduced delivery. Record current and historical codes, operating conditions and live data before clearing them; a power loss may reflect a specific fallback strategy rather than a calibration limit.

Citroën describes an individually selected pump calibration resistor that reports internal pump characteristics to the ECU, and a coolant-temperature protection that can limit fuelling. A resistor substitution is not a validated tuning method; investigate hot-load power reduction alongside temperature, sensor readings and fault state. These details apply to the documented XUD11BTE EPIC configuration.

As a specific identification lead, the Citroën XM 1996 documentation reproduction associates the P8C XUD11BTE L/L3 with Lucas EPIC XUDLC01 and controller reference R04010011B. Match the actual ECU, software, emissions specification and transmission; the reference does not establish that other 2.1 files or EPROMs are interchangeable.

The XM model-year 2000 technical material gives further XUD11BTE/L3 EPIC examples: manual gearbox, PSA ECU 9630509280, supplier R04010020B, software 41502211; automatic, PSA 9631445980, supplier R04010015E, software 41501411. Record the transmission and emissions variant as well as the actual ECU and software numbers when researching files. These catalogue examples do not establish interchangeability.

Owner reports on EPIC repairs and chip work are unverified. A Peugeot 406 2.1 EPIC case describes unstable idle after rotor-sensor work on a pump that was not bench-tested, with calibration need discussed; the reported temporary improvement and suggested remedy are unverified. Inspect fault data and arrange pump-specific testing rather than assuming a sensor swap or shim change fixes another pump.

A Xantia 2.1 TD EPROM installation illustrates electronic calibration work on a Lucas ECU. Different keypad-code outcomes are reported on two vehicles, with uncertainty about another immobiliser configuration. More acceleration smoke is also reported with an EPROM called "V6" than with "V3"; these are chip-revision labels, not engine cylinder counts. The observations are subjective, with no disclosed matched software IDs or controlled air and fuel data. This is not a verified file or interchangeability guide: identify the ECU and memory, preserve a verified original, and understand vehicle-specific coding and recovery before any work.

DK5 2.5 Turbo D Bosch VP36

The Citroën EDC 1.2.8 training reproduction specifically describes the XM DK5 ATE/L3 VP36 pump with MSA11 7.6: the ECU commands metering and advance, receives pump fuel-slide position feedback, and uses engine-speed and needle-lift signals for injection timing. Its illustrated sensor injector is No. 3; the document warns against adjusting that injector because disassembly can damage its sensor. Diagnose the actual control and feedback signals against vehicle-specific service information; mechanical VE LDA instructions do not define this system.

In the documented DK5 VP36 system, the Citroën training identifies separate influences on commanded fuel: driver demand, an air/smoke limit using engine speed, intake pressure and intake-air temperature, an engine-speed-dependent full-load torque limit, overheating protection, fuel-temperature correction and starting enrichment. It also describes closed-loop injection timing using needle-lift feedback and transient fuel shaping to reduce driveline jerk. Log operating state, requested and available signals and temperatures when diagnosing a limit; these functional descriptions do not identify ROM addresses or establish maps for another ECU.

Citroën's 1996 XM documentation reproduction lists Bosch controller 0281001336 for the DK5ATE L3 MSA11 7.6 example. A separate historical tuner ECU list associates that controller number with chip-number entries 2287358818 / 27C256 and 2237355488 / 87C257. The list is an unverified identification lead: it does not establish whether the entries are alternative calibrations or separate devices in one controller, nor does it prove file compatibility, checksum rules or an access method. Identify the physical devices and preserve the actual reads before modification.

The same document describes limited ELIT after-sales coding of parameters including idle, full-load delivery and starting quantity, intended only when necessary. These service adjustments are not evidence of a general tuning method, a safe power increase, or the ability to read or rewrite the ECU's calibration. Establish the exact tool function, original settings and documented recovery procedure before changing any coding.

For later common-rail vehicles see the PSA HDi and BlueHDi diesel tuning guide and Boxer and Relay diesel guide. The PSA ECU identification overview links related petrol and diesel material.

For which pump and injector family is listed against each engine code, from XUD to HDi, see Peugeot and Citroën diesel injection pumps and injectors by engine code. Rail-pressure limits, injector upgrades and coding on common-rail engines are covered in the Peugeot HDi injector and high-pressure pump tuning guide.

Revision 9: Peugeot and Citroen rotary pump diesel tuning guide

Older Peugeot and Citroën diesels include mechanical injection pumps and electronically managed rotary-pump systems. Identify the engine code, exact pump maker and part number, ECU where fitted, vehicle and emissions equipment before choosing service information or considering tuning. These systems do not all use the same controls and cannot be treated as interchangeable with common-rail HDi.

Identify the injection system first

Citroën's XM technical summary lists three distinct examples: the 2.1 Turbo D XUD11 ATE/L with a mechanical pump; XUD11 BTE/L with Lucas Diesel EPIC electronic injection; and 2.5 Turbo D DK5 ATE/L3 with Bosch MSA 11 7.6 and VP36 electronic injection. The document concerns specific multiplexed XM versions and model years; it is not an all-market year cutoff or proof that every XUD pump is mechanical.

Snap-on's 2013 vehicle-communication manual lists both Lucas and Bosch VP20 equipment for the 1.9 turbo diesel DHX in selected Xantia, Evasion, Jumpy, 406, 806 and Expert examples, and lists Lucas or Bosch VP20 for Citroën Saxo 1.5 VJY/VJZ. It is a diagnostic selection guide, not proof of the pump in a particular vehicle. A 1999 Citroën pocket guide reproduction identifies one TUD5 VJZ example with Lucas DPC R8444 B/662C. Read the physical pump identification and match the service procedure.

1.9 XUD turbo diesel: Bosch pump

An owner tutorial for a Peugeot 405 with a 1.9 XUD9/TE and Bosch pump discusses the boost-responsive diaphragm and LDA cone, fuel delivery and turbo pressure; a Lucas-equipped 306 is mentioned separately. 405 owner tutorial. These are individual community claims: the adjustments, quoted pressure limits and performance assertions are not independently verified and do not establish safe settings or apply to Lucas pumps.

Before any pump or boost changes, document the original configuration and service condition, including fuel and intake leaks, cooling, actuator operation and actual boost. A pump specialist can verify timing and delivery against the exact pump specification. Record smoke and temperature under comparable load; visible smoke or a perceived gain alone does not validate fuelling, exhaust temperature or reliability. Keep applicable emissions equipment operational.

Lucas-to-Bosch pump conversions

Owner reports of Lucas-to-Bosch conversions on the 306 DHY and of a 306 XUD9TD swap treat the pump together with its pulley, mount, matching injectors, high-pressure lines, fuel connections and stop control. Owners differ on mounting details, and some Bosch pumps have electronic advance control. 306 DHY Lucas-to-Bosch conversion; 306 XUD9TD swap. These are planning leads, not a universal parts list: match the exact donor pump and vehicle, timing and controls before a conversion, and check the applicable emissions requirements. The XUD service reference specifically notes a different high-pressure pipe set for the XUD9BTF VP20 needle-lift injector, illustrating why a familiar-looking pipe set is not enough to establish compatibility.

One 306 Bosch-conversion owner report describes rough running and smoke after a pump swap, with air observed in the fuel supply. No verified cause is established; inspect the low-pressure fuel supply, leaks and priming as well as timing and the condition of the replacement pump before interpreting the behaviour as a fuelling adjustment problem. 306 Bosch-conversion troubleshooting.

How boost compensation affects fuelling

Bosch's distributor-pump technical instruction, pages 37–39, explains an LDA pressure compensator: charge pressure acts on a spring-loaded diaphragm and tapered control pin, whose follower changes the full-load fuel limit. At lower boost the mechanism restricts full-load delivery; spring preload influences when the diaphragm responds, while the cone and follower govern how movement changes the limit. The LDA affects the pressure-dependent fuel curve, not simply a fixed increase in fuel everywhere.

A 306 Owners Club LDA discussion illustrates these components and owner-proposed modifications. Pin profiles, spring characteristics and pump calibration differ; the alterations and suggested figures there have not been validated as general settings. Before considering a change, check the pressure-signal hose, diaphragm and linkage, and confirm actual boost; a damaged signal path can leave fuel restricted despite boost at the engine. Check response at low, intermediate and higher boost with the pump's own test data rather than judging the curve from a single smoke observation.

Owner-reported XUD build results

Owner-reported rolling-road results for XUD builds show a wide spread. A 306 Owners Club rolling-road results collection lists, for example, a T2/9 mm pump build at 124 bhp and 204 lb-ft and another 9 mm/front-mount-intercooler build at 133 bhp and 228.6 lb-ft. Other listings change the turbo, pump internals or supplementary systems, and some dyno and rpm readings are questioned. In the same collection, one build with a GT15, 11 mm pump, front-mount intercooler and homemade LDA pin is reported at 153 bhp and 286 lb-ft, and a TD04, 11 mm pump, front-mount intercooler and homemade LDA pin at 179 bhp and 250 lb-ft, each said to be an average of three runs on the same named rolling road. Peak-torque rpm, measurement basis and all intervening changes are not established. These are reports rather than controlled comparisons or predicted gains; preserve the full build specification and test conditions when comparing them.

In an XUD7TE pump build, a Bosch 0 460 484 038 is identified as an 8 mm pump with coolant-controlled cold-start features, and a proposed 9 mm donor plunger is reported not to have fitted the original camplate. These are observations about that build, not a validated parts-compatibility table. A diesel specialist's catalogue independently describes that number as VE4/8F2150R403 and lists selected BX 17 turbo and 405 1.8 turbo applications. This corroborates the identification, not interchangeability of modified parts. Head diameter alone does not establish camplate, drive, governor, cold-start or injector compatibility; identify the actual components and have a specialist verify and calibrate the assembled pump.

XUD9TE variable-geometry build example

A 306 XUD9TE D8B project combines a GT2052SV variable-geometry turbo, a custom mapped controller, a modified 11 mm Bosch VE pump and standard injector nozzles. Instrumentation included boost, exhaust-manifold pressure and exhaust-gas temperature. The controller is described as intermittent, which matters when interpreting the build: fitting a VNT to a mechanical-pump engine also requires a suitable vane-control strategy, not merely a fuel-pump change.

The owner reports 154 hp at the wheels and estimates about 175 hp at the flywheel using an assumed transmission loss. Both are an owner's report; a calculated crank figure depends on the loss method and is not an independent measurement. The same owner reports coolant pressurisation, overheating and limited clutch life. Those symptoms and the heavily modified, aged engine do not establish a universal safe or failure threshold.

A separate Peugeot 206 DW8-to-XUD9TE swap and VNT build began as an initially smoky, laggy GT22 setup that exceeded the range of a 30 psi boost gauge. The owner attributed the first episode to actuator direction and a later recurrence to a boost-controller spring; these are owner diagnoses, with several modifications over the project. The build later lists boost, exhaust-gas-temperature and exhaust-manifold-pressure gauges, and a change from an 11 mm to a 10 mm Bosch pump. Check vane movement, actuator direction and the control system, and measure the actual installation; the reported pressures and pump changes are not settings to copy. This was an engine swap, not evidence that the 206 originally carried an XUD9TE.

Static timing is pump-specific

A period XUD service reference lists XUD9 TF/L D8B with Bosch XUD 212 R 513 and a static TDC pump-lift value of 0.66 mm; its XUD9 BTF/L3 DHX Bosch VP20 XUD BP 02 601 example lists 0.57 mm. These are different factory service examples, not performance-tuning targets. Pump piston travel in millimetres is not crankshaft advance in degrees. Use the exact pump, reference position and measuring method from the applicable service documentation, and check timing with the specified equipment.

For that D8B Bosch XUD 212 R 513 example, the period workshop reference additionally lists an indicative dynamic check of 11° ± 1° at 800 rpm, measured on the injection-pump side. It says to check static pump timing if the dynamic value is out of tolerance. This is a pump-specific diagnostic reference, not a tuning target or a direct conversion of the static lift into crankshaft degrees; follow the specified measurement method.

The same reference distinguishes a thermostatic cable-operated fast idle on its XUD9TF example from pneumatic fast-idle actuation on its XUD9BTF. On a cold-running complaint, identify which system is fitted and check its operation before attributing the symptom to the pump's internal calibration.

The same reference identifies the DHX VP20 as semi-electronic, with a load potentiometer, advance solenoid and needle-lift feedback; it separately describes the D8B mechanical pump. Similar Bosch hardware does not imply identical timing control or interchangeable adjustments.

Citroën's VP20 AS3.1 training reproduction adds detail for the documented XUD9BTF: the ECU uses pump load-lever position, engine speed, coolant temperature and needle-lift feedback from injector No. 3 to control its advance solenoid. It describes a pump-mounted boost-dependent fuel limiter and a separate ECU atmospheric-pressure altitude correction; these are different pressure inputs. During deceleration fuel cut, it says needle-lift feedback disappears and advance operates open loop. Check the operating state and the exact system when comparing timing signals; ECU presence alone does not make its control strategy equivalent to EPIC or VP36.

Bosch's VE technical instruction also describes the internal vane supply pump and pressure-control valve establishing speed-dependent housing pressure, which acts on a hydraulic timing piston and changes running advance. The specified overflow restriction or valve supports housing-pressure regulation and returns fuel for cooling and self-venting. Correct static lift alone therefore does not verify running advance: check fuel supply, air ingress and the advance mechanism using the exact-pump procedure. Housing pressure is not high-pressure injector-line pressure; do not obstruct the return as a tuning shortcut.

Bosch's VE instruction distinguishes the pump's start of delivery from the injector's later opening: a pressure wave travels through the high-pressure line before the nozzle opens. The elapsed time translates into a larger crank-angle difference as engine speed rises, and line length also matters. Thus static pump lift, pump delivery timing and needle-lift-based start of injection are different measurements and should not be compared as though they were the same number.

On VE variants equipped with load-dependent start-of-delivery control, Bosch describes a separate load-related timing effect, distinct from the LDA's boost-dependent fuel limit. Establish whether the actual pump has this feature before attributing a part-load timing change to it. A Peugeot 405 Bosch service reference says its XUD7TE procedure temporarily releases the cold-start control during static pump timing and reconnects it afterward. This is specific to that procedure; verify the correct cold-start state for the actual pump.

Lucas mechanical pumps

An owner report on a 306 turbo diesel with a Lucas pump describes little visible smoke during acceleration through the gears but heavy smoke at low speed in a high gear after changes. 306 Lucas pump discussion. That observation is anecdotal and does not validate the suggested settings or establish the cause. It illustrates why comparable load and operating conditions matter: no visible smoke in one test is not proof that fuelling is correct across the full operating range.

A diesel fuel-system reference describes a Lucas DPC turbo-compensator design in which boost acts on diaphragms and alters hydraulic pressure acting on an excess-fuel carriage; an inclined profile makes the increase in maximum delivery progressive. This is a general DPC design example, not evidence that every Lucas-equipped PSA has the same actuator or adjustment. It helps explain why Bosch VE LDA instructions cannot simply be copied to a Lucas pump.

Failure of the Lucas boost-compensator signal path is documented in owner reports: diesel found at the pressure connection with diaphragm failure suspected, and oil filling a similar signal hose. Citroën BX TZD discussion. These are different owner observations, not proof of the cause in another vehicle. A diesel pump specialist lists distinct early and late DPC diaphragm parts. Investigate a leaking or obstructed pressure signal and identify the actual pump; an active fuel leak or fuel entering the intake requires repair before further running.

A Lucas Roto-Diesel timing worksheet describes dial-indicator measurement of pump-plunger lift against engine position and identifies two alternative procedures depending on engine type. Select the vehicle's exact Lucas pump reference, method and specification; do not assume the Bosch measurement procedure, reference position or numerical lift applies.

A pump specialist's DPC application index lists, for example, 8443B453D against Citroën BX 1.7 TD / Peugeot 405 and XUD7TE, and 8443B744B against Citroën XM 2.1 Turbo D XUD11ATE. It is a supplier catalogue lead, not a complete interchangeability list. Match the full pump plate and exact service data before ordering parts or calibrating.

A Partner XUD Lucas service reference says the individual static-timing value for its described pump may be shown on a pump disc or control-lever tag, to be read with the specified indicator and adapter. This is a service-setting identification lead for that procedure, not proof every Lucas pump carries the same tag or uses the same reference position.

For the Saxo 1.5D TUD5 VJZ Lucas DPC, the 1999 Citroën pocket guide describes timing by locating the flywheel, camshaft pulley and pump plate with their specified pins. Its VJZ table describes the initial advance as non-adjustable. This differs from the indicator-based Partner procedure above; identify the precise engine and pump before selecting a method. The same VJZ guide calls for checking that the cold fast-idle cable holds its lever against the stop and is slack when warm, and, with the engine stopped, that the accelerator lever reaches both its full-load and idle stops. Cable or thermostatic-control faults can complicate a pump diagnosis, so establish their condition before changing fuelling.

1.9 DW8B: mechanical pump with electronic timing control

A French vocational diesel examination technical dossier describes a DW8B Lucas DCN2 mechanically driven pump with electronic management. The controller handles functions including injection advance, EGR and pre/post-heating. The load potentiometer is on the pump and the No. 1 injector carries a needle-lift sensor. A separate DW8 service workbook reproduction describes the needle-lift signal as start-of-injection feedback to the diesel control unit. These are distinct from a common-rail pressure control system.

A Peugeot DW8 technical review describes the DW8B advance solenoid as duty-cycle controlled: in its explanation, closing the valve reduces leakage and allows transfer pressure to move the piston toward more advance; opening it reduces piston pressure and permits the return spring to move it toward less advance. The documented valve has an ignition-switched feed and ECU ground control. Check the exact circuit and operating conditions; a multimeter's average voltage is not a direct measurement of injection advance.

Owner reports show how advance faults are misread. A Partner 1.9D owner found that retarding the pump suppressed a warning but produced difficult starting, poor idle and black smoke, together with a mismatch between requested and measured advance. Partner 1.9D advance-fault discussion. This is an unresolved owner account, not a validated repair or reference value; compare specified mechanical timing and requested versus measured advance under documented conditions rather than treating the warning lamp alone as proof of correct timing.

For a timing or running fault, use the relevant vehicle-specific diagnostic and service procedure to assess the load signal, injector feedback, wiring and commanded advance alongside mechanical timing and fuel supply. An ECU in the system does not prove the pump has a conventional common-rail tune or that an HDi definition can be applied.

A 2006 Berlingo DW8B owner compared Lexia timing readings while investigating sluggishness and explicitly lacked a reference value. Berlingo DW8B discussion. The readings and explanations there are not confirmed specifications. Record coolant temperature, speed, load and diagnostic state, and use the correct vehicle and pump documentation for any comparison.

Electronically managed XUD and DK5

The XM examples above distinguish Lucas EPIC and Bosch VP36 systems. Record the pump and controller identities, vehicle configuration, fault codes and current service procedures before deciding whether electronic programming, mechanical repair or specialist pump work is relevant. Do not infer map locations, flash access or wiring from a similar-displacement engine.

XUD11BTE Lucas EPIC

Citroën's XUD11BTE EPIC training reproduction describes ECU-controlled pump metering and advance, a cable-operated accelerator position sensor with a plausibility switch, and inlet pressure and air-temperature inputs. In the documented system the No. 4 injector has needle-lift feedback for measured start of injection and dynamic advance correction. The manufacturer describes the sensor/injector assembly as factory adjusted and prohibits resetting that injector; consult the exact current service procedure. This numbering is specific to the documented system and differs from the DW8B example above.

For one XM P8C XUD11BTE/L3 example, the Citroën XM technical documentation lists holder LCR6734302H for cylinders 1–3 and the needle-lift holder LDC002R01AD3 for cylinder 4. Both are listed at 150 ± 5 bar opening pressure in that particular factory application. This is an injector service reference, not a common-rail pressure or an upgraded tuning target; identify the actual injectors and retain the documented prohibition on resetting the sensor-equipped holder.

In the same EPIC training, two separate metering solenoids regulate fuel-cavity volume and shift the rotor; rotor-position feedback closes the delivery loop. A separate advance solenoid and cam-position sensor control timing, with needle-lift information providing dynamic correction. The diagnostic parameter called rotor decoding is described in microseconds of sensor current build-up, not directly as injected milligrams per stroke. Compare the actual parameter and units between diagnostic tools before interpreting logs.

A Lucas Peugeot/Citroën EPIC after-sales guide reproduction documents Laser 2000 live-data names for its XUD11BTE/L3 system. DEBIT PEDALE is the driver fuel demand calculated from pedal position and rpm; DEBIT MAXIMUM is the operating-condition/map-derived limit, while DEBIT MAX TRANS is a temporary acceleration limit that may exceed it. DEBIT ACTUEL is the corrected pump request; DEBIT BRUT is a more stable average before those corrections. These are distinct calculated quantities, not independently measured injector delivery.

The guide distinguishes requested and measured rotor and cam position, as well as CONS AVANCE DYN (requested dynamic advance) and POS AVANCE DYN (measured from engine speed and needle-lift signals). It describes rotor decoding in microseconds and manifold pressure as absolute. Its rotor-position scale can change between cranking and running, so interpret a jump across that state transition cautiously. Labels, units and sample behaviour can differ on other tools: confirm them before comparing logs or drawing tuning conclusions.

The Lucas EPIC after-sales guide says its absolute manifold-pressure reading should equal local atmospheric pressure before starting. Compare any running reading with a pressure gauge in matching absolute or gauge units. It describes DELAI EV DEBIT + and DELAI EV DEBIT - as adaptive solenoid response delays affected by engine speed, pressure and air passing through the pump. For this diagnostic implementation they are generally below 5 ms; a value that remains above 7 ms indicates an anomaly. These are diagnostic observations for the documented system, not fuel-map settings; confirm the tool's label, units and operating state.

For the documented XUD11BTE/L3 system, the Lucas after-sales guide defines COR. CALAGE POMPE as the correction used to achieve dynamic advance and gives a diagnostic reference of -1.5° to +1.5° at 3,000 rpm with the engine warm and unloaded. This is a conditional service check, not an advance target for tuning. Compare the exact parameter, operating conditions and applicable current service procedure; a correction value alone does not prove the static pump timing is correct.

Citroën's XUD11BTE training notes that rotor- or cam-position faults can be recorded following fuel-filter replacement while the pump self-degasses. Its procedure calls for clearing those faults after the engine has run. Record existing fault history and symptoms first, and investigate any recurring fault; this note does not explain every rotor or cam code.

The EPIC after-sales guide lists different fallback actions for different fault codes. For example, an accelerator-position plausibility fault can restrict fuel demand, while some other faults use substitute sensor values or reduced delivery. Record current and historical codes, operating conditions and live data before clearing them; a power loss may reflect a specific fallback strategy rather than a calibration limit.

Citroën describes an individually selected pump calibration resistor that reports internal pump characteristics to the ECU, and a coolant-temperature protection that can limit fuelling. A resistor substitution is not a validated tuning method; investigate hot-load power reduction alongside temperature, sensor readings and fault state. These details apply to the documented XUD11BTE EPIC configuration.

As a specific identification lead, the Citroën XM 1996 documentation reproduction associates the P8C XUD11BTE L/L3 with Lucas EPIC XUDLC01 and controller reference R04010011B. Match the actual ECU, software, emissions specification and transmission; the reference does not establish that other 2.1 files or EPROMs are interchangeable.

The XM model-year 2000 technical material gives further XUD11BTE/L3 EPIC examples: manual gearbox, PSA ECU 9630509280, supplier R04010020B, software 41502211; automatic, PSA 9631445980, supplier R04010015E, software 41501411. Record the transmission and emissions variant as well as the actual ECU and software numbers when researching files. These catalogue examples do not establish interchangeability.

Owner reports on EPIC repairs and chip work are unverified. A Peugeot 406 2.1 EPIC case describes unstable idle after rotor-sensor work on a pump that was not bench-tested, with calibration need discussed; the reported temporary improvement and suggested remedy are unverified. Inspect fault data and arrange pump-specific testing rather than assuming a sensor swap or shim change fixes another pump.

A Xantia 2.1 TD EPROM installation illustrates electronic calibration work on a Lucas ECU. Different keypad-code outcomes are reported on two vehicles, with uncertainty about another immobiliser configuration. More acceleration smoke is also reported with an EPROM called "V6" than with "V3"; these are chip-revision labels, not engine cylinder counts. The observations are subjective, with no disclosed matched software IDs or controlled air and fuel data. This is not a verified file or interchangeability guide: identify the ECU and memory, preserve a verified original, and understand vehicle-specific coding and recovery before any work.

DK5 2.5 Turbo D Bosch VP36

The Citroën EDC 1.2.8 training reproduction specifically describes the XM DK5 ATE/L3 VP36 pump with MSA11 7.6: the ECU commands metering and advance, receives pump fuel-slide position feedback, and uses engine-speed and needle-lift signals for injection timing. Its illustrated sensor injector is No. 3; the document warns against adjusting that injector because disassembly can damage its sensor. Diagnose the actual control and feedback signals against vehicle-specific service information; mechanical VE LDA instructions do not define this system.

In the documented DK5 VP36 system, the Citroën training identifies separate influences on commanded fuel: driver demand, an air/smoke limit using engine speed, intake pressure and intake-air temperature, an engine-speed-dependent full-load torque limit, overheating protection, fuel-temperature correction and starting enrichment. It also describes closed-loop injection timing using needle-lift feedback and transient fuel shaping to reduce driveline jerk. Log operating state, requested and available signals and temperatures when diagnosing a limit; these functional descriptions do not identify ROM addresses or establish maps for another ECU.

Citroën's 1996 XM documentation reproduction lists Bosch controller 0281001336 for the DK5ATE L3 MSA11 7.6 example. A separate historical tuner ECU list associates that controller number with chip-number entries 2287358818 / 27C256 and 2237355488 / 87C257. The list is an unverified identification lead: it does not establish whether the entries are alternative calibrations or separate devices in one controller, nor does it prove file compatibility, checksum rules or an access method. Identify the physical devices and preserve the actual reads before modification.

The same document describes limited ELIT after-sales coding of parameters including idle, full-load delivery and starting quantity, intended only when necessary. These service adjustments are not evidence of a general tuning method, a safe power increase, or the ability to read or rewrite the ECU's calibration. Establish the exact tool function, original settings and documented recovery procedure before changing any coding.

For later common-rail vehicles see the PSA HDi and BlueHDi diesel tuning guide and Boxer and Relay diesel guide. The PSA ECU identification overview links related petrol and diesel material.

For which pump and injector family is listed against each engine code, from XUD to HDi, see Peugeot and Citroën diesel injection pumps and injectors by engine code. Rail-pressure limits, injector upgrades and coding on common-rail engines are covered in the Peugeot HDi injector and high-pressure pump tuning guide.