Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Jeep

This guide concerns selected 2005-06 Jeep Wrangler TJ and long-wheelbase Unlimited (LJ) vehicles with the 4.0-litre inline-six and 42RLE automatic. It combines factory specifications and HP Tuners coverage with owner reports about upshifts after tyre and axle changes. Record the vehicle, PCM calibration and installed transmission before using an example.

Engine, gearbox and support

Jeep's 2005 Wrangler Unlimited specifications describe a 3,956 cc overhead-valve 12-valve inline-six with sequential multiport injection, cast-iron block and head, and US ratings of 190 bhp at 4,600 rpm and 235 lb-ft at 3,200 rpm. They list the 42RLE four-speed automatic with 2.84, 1.57, 1.00 and 0.69:1 forward ratios and an electronically controlled converter clutch. The 2005 specification also lists a six-speed manual; the automatic's details do not apply to that transmission. Factory configuration, gear ratio and equipment differ by trim and market. Jeep: 2005 Wrangler Unlimited specifications.

HP Tuners lists 2005-06 Wrangler TJ 2.4 and 4.0 as vehicle applications. That is not a promise of every shift table, channel, gearbox or controller modification on every car. Confirm the actual PCM and transmission, VCM Suite version, interface and licensing with HP Tuners. An older owner report states that 2005-06 cars have integrated transmission control; the same access should not be inferred for an earlier vehicle just because it also has a 42RLE. TJ forum report on 42RLE shift points; HP Tuners: Stellantis vehicle list.

The 2005 Wrangler service-manual description says the 42RLE is hydraulically operated with adaptive electronic controls, and identifies a TCM section of the PCM. Shift commands, hydraulic response and mechanical condition are different parts of a shift event.

Tyres, final drive and the overdrive complaint

At the same actual road speed, tyre rolling circumference, selected gear and converter condition, a numerically higher axle ratio raises engine speed. A larger rolling tyre circumference tends to lower engine speed at the same road speed and gearing. A shift schedule changes when a gear is requested; it does not physically change the 0.69:1 fourth-gear ratio or axle gearing. Torque-converter slip and lockup also affect rpm, so compare gear and converter state rather than assuming every rpm drop is a shift. Measure actual road speed independently and verify the vehicle's speed signal after modifications.

Owner-reported worked examples show the effect on modified vehicles. A TJ/LJ owner with reported 35-inch tyres and 4.88 axle gears described early fourth-gear engagement and difficulty requesting a 4-3 downshift, and reported that changes to HP Tuners upshift and downshift schedules improved the way the vehicle drove on local hills. This is a subjective result on one modified Jeep, not a validated shift-speed table or a universal recommendation. 2024 TJ/LJ shift-schedule report.

A second 2005 LJ owner with 33-inch tyres and 3.73 gearing reported better manual-throttle hill behaviour after trying the first owner's schedule, but said the vehicle tended to remain in third when cruise control was engaged. Further changes were planned; no controlled comparison or final validated settings are provided. This illustrates why a schedule should be evaluated under cruise as well as driver-controlled throttle and why another vehicle's numbers should not be copied. Continuation of the shift-schedule report.

Verify which table and mode are active

A 2005 LJ owner reported seeing fewer transmission tabs than a screenshot posted elsewhere, and another owner attributed the more extensive screenshot to a different transmission. That identification is an owner observation, not independent proof of the screenshot's exact calibration. A fifth-gear-looking label or an unfamiliar table does not establish that the four-speed 42RLE has a fifth physical gear. Confirm controller, software, table definition, axis units and active drive, overdrive and temperature conditions before making a change. Check what VCM Editor actually exposes for the file rather than relying on a screenshot from another Jeep.

On the related distinction between shift and converter clutch behaviour, one TJ owner described using the overdrive button to affect the vehicle's gear and lockup behaviour. Treat that as one driver's observation: confirm the actual command and speed traces on the vehicle being investigated, and consult the appropriate service information.

Practical logging and validation

  1. Record diagnostic trouble codes before reading the vehicle, because HP Tuners warns that reading may clear them. Save the original supported read and note calibration, tyre rolling size, axle ratio, fuel and other changes. HP Tuners: getting started.
  2. In VCM Scanner, record road speed, engine speed, throttle or pedal, engine and transmission temperature, requested/current gear, overdrive state, converter-clutch command and slip or transmission input/output speeds where the installed controller exposes reliable channels. A layout does not add the underlying channels automatically; check units and update rate. HP Tuners: scanner layouts.
  3. Compare repeatable light- and moderate-throttle events, flat road and hills, overdrive enabled and disabled, and cruise when appropriate. A commanded shift is not proof the clutches applied correctly. Investigate fluid, faults, wiring, converter and mechanical/hydraulic state before changing calibration to mask a symptom.
  4. Review the actual upshift and downshift definitions and their interaction across the operating range. Make documented, limited changes, then log comparable conditions again. Preserve protective functions and do not transplant values or entire tunes from a different vehicle.

Not established

No validated shift-speed table for modified tyre and axle combinations is documented, and the cruise-control behaviour on the 33-inch LJ was not resolved.

Related: Jeep Wrangler generations and engines; HP Tuners MPVI4; later Wrangler and Gladiator 3.6/850RE guide.