Page organisation in this revision
- Page type
- Technical article
- Subject
- Tuning
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Ford
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
A MAF histogram that puts every sample into its first cell is usually a scanner setup problem rather than evidence that the MAF curve needs a large change. Owner reports on a 2014 Mustang GT 5.0 and another first-generation Coyote Mustang using HP Tuners identify the causes below; the exact channels and fixes should not be assumed for later engines or other calibrations.
Reported causes
On the 2014 car, the fuel-trim histogram populated only its first cell because the selected MAF Airflow vs Period input had not been added to the scanner's channel list. Decimal commas also interfered with copied axis labels; changing the computer's regional number format made those labels paste correctly, and the owner reported that the graph then worked. 2014 Mustang GT report.
On the second Coyote, the appropriate period channel became available after connecting to the vehicle. A tutor's advice was to verify that the axis channel really updates and that its breakpoints suit the signal's range. Gen 1 Coyote report.
Practical checks
Connect to the vehicle so VCM Scanner can establish the vehicle profile. Select the relevant module and add the actual axis input and the data being plotted to the channel list. A graph layout alone does not add its input channels.
View the axis input live or in a time chart to confirm that it changes. Check for similarly named channels and the correct module source.
Compare the graph's axis type, units and breakpoints with the target table and the observed channel range. A frequency, a period and a calculated mass-flow channel are not interchangeable table axes. If displaying a different input for diagnosis, configure its own scale; do not paste those bins into a table with an incompatible axis.
If copied numerical labels look wrong, inspect the pasted values and decimal format before drawing conclusions. Save the corrected channel configuration and layout.
HP Tuners documents the vehicle-profile and channel setup and explains that layouts need corresponding channel inputs.
Using the data
Assess fuel trims only where closed-loop trimming is active, verify the fuel system and sensor data, and compare both banks where available. A wideband and suitable supporting measurements are needed to assess mixture in conditions where fuel trims are not active. Check sample coverage and operating conditions before considering any MAF adjustment, and validate with a fresh log. Other Ford calibrations can use different channels and airflow models; consult the exact file and current HP Tuners compatibility guidance. HPA: fuel-trim limitations.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Ford Mustang 5.0 Coyote: HP Tuners MAF histogram troubleshooting
A MAF histogram that puts every sample into its first cell is usually a scanner setup problem rather than evidence that the MAF curve needs a large change. Owner reports on a 2014 Mustang GT 5.0 and another first-generation Coyote Mustang using HP Tuners identify the causes below; the exact channels and fixes should not be assumed for later engines or other calibrations.
Reported causes
On the 2014 car, the fuel-trim histogram populated only its first cell because the selected MAF Airflow vs Period input had not been added to the scanner's channel list. Decimal commas also interfered with copied axis labels; changing the computer's regional number format made those labels paste correctly, and the owner reported that the graph then worked. 2014 Mustang GT report.
On the second Coyote, the appropriate period channel became available after connecting to the vehicle. A tutor's advice was to verify that the axis channel really updates and that its breakpoints suit the signal's range. Gen 1 Coyote report.
Practical checks
- Connect to the vehicle so VCM Scanner can establish the vehicle profile. Select the relevant module and add the actual axis input and the data being plotted to the channel list. A graph layout alone does not add its input channels.
- View the axis input live or in a time chart to confirm that it changes. Check for similarly named channels and the correct module source.
- Compare the graph's axis type, units and breakpoints with the target table and the observed channel range. A frequency, a period and a calculated mass-flow channel are not interchangeable table axes. If displaying a different input for diagnosis, configure its own scale; do not paste those bins into a table with an incompatible axis.
- If copied numerical labels look wrong, inspect the pasted values and decimal format before drawing conclusions. Save the corrected channel configuration and layout.
HP Tuners documents the vehicle-profile and channel setup and explains that layouts need corresponding channel inputs.
Using the data
Assess fuel trims only where closed-loop trimming is active, verify the fuel system and sensor data, and compare both banks where available. A wideband and suitable supporting measurements are needed to assess mixture in conditions where fuel trims are not active. Check sample coverage and operating conditions before considering any MAF adjustment, and validate with a fresh log. Other Ford calibrations can use different channels and airflow models; consult the exact file and current HP Tuners compatibility guidance. HPA: fuel-trim limitations.
Revision 2: Ford Mustang 5.0 Coyote: HP Tuners MAF histogram troubleshooting
A MAF histogram that puts every sample into its first cell is usually a scanner setup problem rather than evidence that the MAF curve needs a large change. Owner reports on a 2014 Mustang GT 5.0 and another first-generation Coyote Mustang using HP Tuners identify the causes below; the exact channels and fixes should not be assumed for later engines or other calibrations.
Reported causes
On the 2014 car, the fuel-trim histogram populated only its first cell because the selected MAF Airflow vs Period input had not been added to the scanner's channel list. Decimal commas also interfered with copied axis labels; changing the computer's regional number format made those labels paste correctly, and the owner reported that the graph then worked. 2014 Mustang GT report.
On the second Coyote, the appropriate period channel became available after connecting to the vehicle. A tutor's advice was to verify that the axis channel really updates and that its breakpoints suit the signal's range. Gen 1 Coyote report.
Practical checks
- Connect to the vehicle so VCM Scanner can establish the vehicle profile. Select the relevant module and add the actual axis input and the data being plotted to the channel list. A graph layout alone does not add its input channels.
- View the axis input live or in a time chart to confirm that it changes. Check for similarly named channels and the correct module source.
- Compare the graph's axis type, units and breakpoints with the target table and the observed channel range. A frequency, a period and a calculated mass-flow channel are not interchangeable table axes. If displaying a different input for diagnosis, configure its own scale; do not paste those bins into a table with an incompatible axis.
- If copied numerical labels look wrong, inspect the pasted values and decimal format before drawing conclusions. Save the corrected channel configuration and layout.
HP Tuners documents the vehicle-profile and channel setup and explains that layouts need corresponding channel inputs.
Using the data
Assess fuel trims only where closed-loop trimming is active, verify the fuel system and sensor data, and compare both banks where available. A wideband and suitable supporting measurements are needed to assess mixture in conditions where fuel trims are not active. Check sample coverage and operating conditions before considering any MAF adjustment, and validate with a fresh log. Other Ford calibrations can use different channels and airflow models; consult the exact file and current HP Tuners compatibility guidance. HPA: fuel-trim limitations.