Page organisation in this revision
- Page type
- Technical article
- Subject
- Performance
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Exhaust gas temperature (EGT) is one of the channels worth logging on a tuned engine, because it shows the thermal load on the valves, turbine and catalytic converter. It is evidence, not a mixture measurement and not a safe-limit chart. This page covers how it is measured and how to use it. Other channels are in the validation list on engine performance upgrades.
What an EGT gauge measures
An EGT gauge reads exhaust gas temperature with a thermocouple-type pyrometer, and drivers and pilots use it to estimate the air-fuel ratio (Wikipedia: Exhaust gas temperature gauge). The temperature moves with mixture, ignition timing, load and engine speed, so one reading means little without the other operating conditions.
Where the sensor goes
On a turbocharged car, a sensor at the manifold collector, before the turbo, reads the turbine inlet temperature, and a sensor after the turbo reads a lower exhaust temperature. Exhaust gas typically cools by about 93 to 149 °C (200 to 300 °F) across the turbine, so installers place the thermocouple as close to the cylinder head as practical for a truer and faster reading. Report where the sensor was fitted with any reading, because a post-turbo figure cannot be compared with a pre-turbo one. Fit the sensor with the sensor maker's boss and instructions, and keep it clear of leaks, which cool the reading.
What it tells you
Thermal load. A rising temperature means more heat reaching the valves, turbine and converter. Retarding spark to avoid knock moves combustion into the exhaust stroke and raises exhaust temperature: ignition tuning.
Mixture, indirectly. EGT peaks near the point where the mixture burns hottest, and aircraft practice shows how the peak is used, but the source flags those claims as unsourced and they do not carry over to a road engine. Use a wideband sensor to measure mixture: air-fuel ratio and wideband lambda sensors.
A lean or misfiring cylinder. One hot cylinder can show up where a collector sensor cannot, so a single-point reading does not prove every cylinder is safe.Thermal load. A rising temperature means more heat reaching the valves, turbine and converter. Retarding spark to avoid knock moves combustion into the exhaust stroke and raises exhaust temperature: ignition timing for performance.
Mixture, indirectly. EGT peaks near the point where the mixture burns hottest, and aircraft practice shows how the peak is used, but the source flags those claims as unsourced and they do not carry over to a road engine. Use a wideband sensor to measure mixture: air-fuel ratio and wideband lambda sensors.
A lean or misfiring cylinder. One hot cylinder can show up where a collector sensor cannot, so a single-point reading does not prove every cylinder is safe.The article describes EGT on its own as an older tuning method and says some tuners pair it with a wideband sensor, but flags both claims as lacking citations. Treat EGT as one signal alongside lambda, knock correction and boost.
Limits
Very high exhaust temperatures can indicate dangerous conditions that may lead to catastrophic failure. A figure often quoted is above about 900 °C (1,600 °F), but the source gives that without a citation and it is not a safe limit for any particular engine. The limit depends on the engine, the turbine and the converter, so use the engine, turbo and converter makers' figures for the exact parts, and log temperature during testing to see whether it climbs. See burnt valves for what sustained heat does to exhaust valves, and catalytic converters and performance for the effect on the converter.
Using it
Log EGT with boost, load, lambda, ignition and knock correction, so that a rise can be explained.
Establish a baseline at known-safe conditions, and look for change after a modification.
Compare like with like: same sensor position, similar air temperature and cooling, and the same fuel.
Do not tune to a single EGT figure. Stop and investigate if temperature climbs without an obvious cause.
Sources
Exhaust gas temperature gauge. Wikipedia. Measurement, sensor position, temperature drop across the turbine and the unsourced 900 °C warning. The article is flagged as needing more citations. Accessed 2026-11-19.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Exhaust gas temperature monitoring
Exhaust gas temperature (EGT) is one of the channels worth logging on a tuned engine, because it shows the thermal load on the valves, turbine and catalytic converter. It is evidence, not a mixture measurement and not a safe-limit chart. This page covers how it is measured and how to use it. Other channels are in the validation list on engine performance upgrades.
What an EGT gauge measures
An EGT gauge reads exhaust gas temperature with a thermocouple-type pyrometer, and drivers and pilots use it to estimate the air-fuel ratio (Wikipedia: Exhaust gas temperature gauge). The temperature moves with mixture, ignition timing, load and engine speed, so one reading means little without the other operating conditions.
Where the sensor goes
On a turbocharged car, a sensor at the manifold collector, before the turbo, reads the turbine inlet temperature, and a sensor after the turbo reads a lower exhaust temperature. Exhaust gas typically cools by about 93 to 149 °C (200 to 300 °F) across the turbine, so installers place the thermocouple as close to the cylinder head as practical for a truer and faster reading. Report where the sensor was fitted with any reading, because a post-turbo figure cannot be compared with a pre-turbo one. Fit the sensor with the sensor maker's boss and instructions, and keep it clear of leaks, which cool the reading.
What it tells you
- Thermal load. A rising temperature means more heat reaching the valves, turbine and converter. Retarding spark to avoid knock moves combustion into the exhaust stroke and raises exhaust temperature: ignition timing for performance.
- Mixture, indirectly. EGT peaks near the point where the mixture burns hottest, and aircraft practice shows how the peak is used, but the source flags those claims as unsourced and they do not carry over to a road engine. Use a wideband sensor to measure mixture: air-fuel ratio and wideband lambda sensors.
- A lean or misfiring cylinder. One hot cylinder can show up where a collector sensor cannot, so a single-point reading does not prove every cylinder is safe.
The article describes EGT on its own as an older tuning method and says some tuners pair it with a wideband sensor, but flags both claims as lacking citations. Treat EGT as one signal alongside lambda, knock correction and boost.
Limits
Very high exhaust temperatures can indicate dangerous conditions that may lead to catastrophic failure. A figure often quoted is above about 900 °C (1,600 °F), but the source gives that without a citation and it is not a safe limit for any particular engine. The limit depends on the engine, the turbine and the converter, so use the engine, turbo and converter makers' figures for the exact parts, and log temperature during testing to see whether it climbs. See burnt valves for what sustained heat does to exhaust valves, and catalytic converters and performance for the effect on the converter.
Using it
- Log EGT with boost, load, lambda, ignition and knock correction, so that a rise can be explained.
- Establish a baseline at known-safe conditions, and look for change after a modification.
- Compare like with like: same sensor position, similar air temperature and cooling, and the same fuel.
- Do not tune to a single EGT figure. Stop and investigate if temperature climbs without an obvious cause.
Sources
- Exhaust gas temperature gauge. Wikipedia. Measurement, sensor position, temperature drop across the turbine and the unsourced 900 °C warning. The article is flagged as needing more citations. Accessed 2026-11-19.
Revision 2: Exhaust gas temperature monitoring
Exhaust gas temperature (EGT) is one of the channels worth logging on a tuned engine, because it shows the thermal load on the valves, turbine and catalytic converter. It is evidence, not a mixture measurement and not a safe-limit chart. This page covers how it is measured and how to use it. Other channels are in the validation list on engine performance upgrades.
What an EGT gauge measures
An EGT gauge reads exhaust gas temperature with a thermocouple-type pyrometer, and drivers and pilots use it to estimate the air-fuel ratio (Wikipedia: Exhaust gas temperature gauge). The temperature moves with mixture, ignition timing, load and engine speed, so one reading means little without the other operating conditions.
Where the sensor goes
On a turbocharged car, a sensor at the manifold collector, before the turbo, reads the turbine inlet temperature, and a sensor after the turbo reads a lower exhaust temperature. Exhaust gas typically cools by about 93 to 149 °C (200 to 300 °F) across the turbine, so installers place the thermocouple as close to the cylinder head as practical for a truer and faster reading. Report where the sensor was fitted with any reading, because a post-turbo figure cannot be compared with a pre-turbo one. Fit the sensor with the sensor maker's boss and instructions, and keep it clear of leaks, which cool the reading.
What it tells you
- Thermal load. A rising temperature means more heat reaching the valves, turbine and converter. Retarding spark to avoid knock moves combustion into the exhaust stroke and raises exhaust temperature: ignition tuning.
- Mixture, indirectly. EGT peaks near the point where the mixture burns hottest, and aircraft practice shows how the peak is used, but the source flags those claims as unsourced and they do not carry over to a road engine. Use a wideband sensor to measure mixture: air-fuel ratio and wideband lambda sensors.
- A lean or misfiring cylinder. One hot cylinder can show up where a collector sensor cannot, so a single-point reading does not prove every cylinder is safe.
The article describes EGT on its own as an older tuning method and says some tuners pair it with a wideband sensor, but flags both claims as lacking citations. Treat EGT as one signal alongside lambda, knock correction and boost.
Limits
Very high exhaust temperatures can indicate dangerous conditions that may lead to catastrophic failure. A figure often quoted is above about 900 °C (1,600 °F), but the source gives that without a citation and it is not a safe limit for any particular engine. The limit depends on the engine, the turbine and the converter, so use the engine, turbo and converter makers' figures for the exact parts, and log temperature during testing to see whether it climbs. See burnt valves for what sustained heat does to exhaust valves, and catalytic converters and performance for the effect on the converter.
Using it
- Log EGT with boost, load, lambda, ignition and knock correction, so that a rise can be explained.
- Establish a baseline at known-safe conditions, and look for change after a modification.
- Compare like with like: same sensor position, similar air temperature and cooling, and the same fuel.
- Do not tune to a single EGT figure. Stop and investigate if temperature climbs without an obvious cause.
Sources
- Exhaust gas temperature gauge. Wikipedia. Measurement, sensor position, temperature drop across the turbine and the unsourced 900 °C warning. The article is flagged as needing more citations. Accessed 2026-11-19.