Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Diagnostics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Chevrolet, GMC

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Engine, transmissions and controller identification

The L5P is GM's 6.6-litre turbo-diesel V8; the published specification for the later version is 6,604 cc, overhead valves with four valves per cylinder, and high-pressure common-rail direct injection. In GM's 2024 Silverado HD ZR2 example the diesel is rated at 470 hp and 975 lb-ft, paired with an Allison 10L1000 ten-speed automatic. Those ratings and the gearbox are specific to that application, not all L5P trucks. Verify the VIN and actual driveline before using torque limits, service data or parts information. GM L5P engine specifications; GM: 2024 Silverado HD ZR2 specifications.

HP Tuners identifies E41 ECM with T87A TCM in its 2017-19 L5P group and E41 with T93 in its 2020-23 group. Its 2024-26 Silverado/Sierra 2500/3500 L5P coverage uses the E42 ECM. These are HP Tuners' published application groups; identify the modules installed and check current ECU and TCM support separately. An engine-controller licence or service does not establish transmission tuning support. HP Tuners: L5P model-year groups; 2026 E42 applications.

E41 access and switchable calibration

HP Tuners announced a direct OBD upgrade for listed 2018-23 E41 L5P applications; its 2017 model requires the specified kit or send-in service in that announcement. Later E42 applications have different service requirements. Equipment, software and credits change, so confirm the current instructions for the vehicle rather than applying an older forum unlock procedure. E41 OBD upgrade announcement; E42 service.

HP Tuners' 2022 L5P/L5D E41 Switch on the Fly guide shows separately selectable groups including desired boost, desired/max vane position and fuel pressure. It says the switchable groups initially use their OEM lookup until enabled; a displayed slot does not by itself prove a particular group is using slot data. Confirm the actual OS, table enables, slot and conditions before attributing a result to a map. The guide describes an OS-modification save/close/reopen and initial write sequence; follow the current product's exact on-screen instructions, since an incorrect procedure can damage the controller. HP Tuners: L5P/L5D SOTF guide.

Logging an L5P

For an L5P/L5D log, a specialist describes loading the appropriate channel configuration and capturing the symptom, with a short baseline before testing. Configure the channels for the actual ECM, save the log and label the conditions; a full-throttle run is not necessary for every fault. DuramaxTuner logging procedure; HP Tuners channel setup.

Using the log to separate possibilities

At the point of a repeatable symptom, compare the available MAF signal with engine speed, driver demand/load and requested versus actual rail pressure; review recorded DTCs and the time trace rather than only average values. Inspect the intake, sensor and connections using the appropriate service information. A rail-pressure trace that looks normal does not prove the airflow signal is healthy. Transmission-slip indications are assessed separately.

An owner report illustrates this. A part-throttle stumble followed a change of turbo hardware; HP Tuners logs appeared to show actual rail pressure following the requested value, while misfires and torque-converter slip were also discussed. A suspected MAF signal problem was identified from the log, and a replacement MAF reportedly resolved the symptom. The truck's exact model year and the raw log were not independently verified, and this single owner-reported repair does not establish that every L5P stumble is a MAF fault. L5P owner discussion and follow-up.

Unresolved owner and tuner reports

An HP Tuners user on 2017-19 T87A trucks reported that changes to part-throttle shift tables did not produce the expected change and that normal and tow/haul logs differed; the user supplied OS 24285377 but no confirmed solution was reached. Compare mode, load, actual and commanded gear, speed and conditions in the actual truck; do not infer a universal table defect or copy another OS's values. 2017-19 T87A discussion.

Another L5P owner report describes an HP Tuners log and continuing P0191 rail-pressure problems after several parts were replaced, without establishing a final repair. It illustrates why an apparently normal short log or previous parts replacement should be assessed alongside the symptom, DTC conditions and manufacturer diagnostic tests rather than taken as proof of a particular fault.

Injector circuit evidence

GM bulletin 23-NA-027 covers specified 2017-23 Silverado/Sierra 2500HD and 3500HD L5P applications and describes injector-connector terminal wear associated with applicable misfire or injector-circuit codes. GM's PIP5582 describes grouped injector-driver behaviour for specified 2017-18 L5P trucks. Use the actual vehicle's VIN, market and current service information to check applicability. Multiple cylinder indications should be investigated at the circuit and driver level, not assumed to be simultaneous failed injectors.

Preserve diagnostic information and confirm sensor readings before making calibration changes or replacing parts. HP Tuners' Scanner configuration guidance explains how to select vehicle-specific channels. Tuning support and E41 service requirements vary by application; see the tool listing.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: GM L5P Duramax: engine, HP Tuners tuning and diagnosis

Engine, transmissions and controller identification

The L5P is GM's 6.6-litre turbo-diesel V8; the published specification for the later version is 6,604 cc, overhead valves with four valves per cylinder, and high-pressure common-rail direct injection. In GM's 2024 Silverado HD ZR2 example the diesel is rated at 470 hp and 975 lb-ft, paired with an Allison 10L1000 ten-speed automatic. Those ratings and the gearbox are specific to that application, not all L5P trucks. Verify the VIN and actual driveline before using torque limits, service data or parts information. GM L5P engine specifications; GM: 2024 Silverado HD ZR2 specifications.

HP Tuners identifies E41 ECM with T87A TCM in its 2017-19 L5P group and E41 with T93 in its 2020-23 group. Its 2024-26 Silverado/Sierra 2500/3500 L5P coverage uses the E42 ECM. These are HP Tuners' published application groups; identify the modules installed and check current ECU and TCM support separately. An engine-controller licence or service does not establish transmission tuning support. HP Tuners: L5P model-year groups; 2026 E42 applications.

E41 access and switchable calibration

HP Tuners announced a direct OBD upgrade for listed 2018-23 E41 L5P applications; its 2017 model requires the specified kit or send-in service in that announcement. Later E42 applications have different service requirements. Equipment, software and credits change, so confirm the current instructions for the vehicle rather than applying an older forum unlock procedure. E41 OBD upgrade announcement; E42 service.

HP Tuners' 2022 L5P/L5D E41 Switch on the Fly guide shows separately selectable groups including desired boost, desired/max vane position and fuel pressure. It says the switchable groups initially use their OEM lookup until enabled; a displayed slot does not by itself prove a particular group is using slot data. Confirm the actual OS, table enables, slot and conditions before attributing a result to a map. The guide describes an OS-modification save/close/reopen and initial write sequence; follow the current product's exact on-screen instructions, since an incorrect procedure can damage the controller. HP Tuners: L5P/L5D SOTF guide.

Logging an L5P

For an L5P/L5D log, a specialist describes loading the appropriate channel configuration and capturing the symptom, with a short baseline before testing. Configure the channels for the actual ECM, save the log and label the conditions; a full-throttle run is not necessary for every fault. DuramaxTuner logging procedure; HP Tuners channel setup.

Using the log to separate possibilities

At the point of a repeatable symptom, compare the available MAF signal with engine speed, driver demand/load and requested versus actual rail pressure; review recorded DTCs and the time trace rather than only average values. Inspect the intake, sensor and connections using the appropriate service information. A rail-pressure trace that looks normal does not prove the airflow signal is healthy. Transmission-slip indications are assessed separately.

An owner report illustrates this. A part-throttle stumble followed a change of turbo hardware; HP Tuners logs appeared to show actual rail pressure following the requested value, while misfires and torque-converter slip were also discussed. A suspected MAF signal problem was identified from the log, and a replacement MAF reportedly resolved the symptom. The truck's exact model year and the raw log were not independently verified, and this single owner-reported repair does not establish that every L5P stumble is a MAF fault. L5P owner discussion and follow-up.

Unresolved owner and tuner reports

An HP Tuners user on 2017-19 T87A trucks reported that changes to part-throttle shift tables did not produce the expected change and that normal and tow/haul logs differed; the user supplied OS 24285377 but no confirmed solution was reached. Compare mode, load, actual and commanded gear, speed and conditions in the actual truck; do not infer a universal table defect or copy another OS's values. 2017-19 T87A discussion.

Another L5P owner report describes an HP Tuners log and continuing P0191 rail-pressure problems after several parts were replaced, without establishing a final repair. It illustrates why an apparently normal short log or previous parts replacement should be assessed alongside the symptom, DTC conditions and manufacturer diagnostic tests rather than taken as proof of a particular fault.

Injector circuit evidence

GM bulletin 23-NA-027 covers specified 2017-23 Silverado/Sierra 2500HD and 3500HD L5P applications and describes injector-connector terminal wear associated with applicable misfire or injector-circuit codes. GM's PIP5582 describes grouped injector-driver behaviour for specified 2017-18 L5P trucks. Use the actual vehicle's VIN, market and current service information to check applicability. Multiple cylinder indications should be investigated at the circuit and driver level, not assumed to be simultaneous failed injectors.

Preserve diagnostic information and confirm sensor readings before making calibration changes or replacing parts. HP Tuners' Scanner configuration guidance explains how to select vehicle-specific channels. Tuning support and E41 service requirements vary by application; see the tool listing.

Revision 3: GM L5P Duramax: engine, HP Tuners tuning and diagnosis

Engine, transmissions and controller identification

The L5P is GM's 6.6-litre turbo-diesel V8; the published specification for the later version is 6,604 cc, overhead valves with four valves per cylinder, and high-pressure common-rail direct injection. In GM's 2024 Silverado HD ZR2 example the diesel is rated at 470 hp and 975 lb-ft, paired with an Allison 10L1000 ten-speed automatic. Those ratings and the gearbox are specific to that application, not all L5P trucks. Verify the VIN and actual driveline before using torque limits, service data or parts information. GM L5P engine specifications; GM: 2024 Silverado HD ZR2 specifications.

HP Tuners identifies E41 ECM with T87A TCM in its 2017-19 L5P group and E41 with T93 in its 2020-23 group. Its 2024-26 Silverado/Sierra 2500/3500 L5P coverage uses the E42 ECM. These are HP Tuners' published application groups; identify the modules installed and check current ECU and TCM support separately. An engine-controller licence or service does not establish transmission tuning support. HP Tuners: L5P model-year groups; 2026 E42 applications.

E41 access and switchable calibration

HP Tuners announced a direct OBD upgrade for listed 2018-23 E41 L5P applications; its 2017 model requires the specified kit or send-in service in that announcement. Later E42 applications have different service requirements. Equipment, software and credits change, so confirm the current instructions for the vehicle rather than applying an older forum unlock procedure. E41 OBD upgrade announcement; E42 service.

HP Tuners' 2022 L5P/L5D E41 Switch on the Fly guide shows separately selectable groups including desired boost, desired/max vane position and fuel pressure. It says the switchable groups initially use their OEM lookup until enabled; a displayed slot does not by itself prove a particular group is using slot data. Confirm the actual OS, table enables, slot and conditions before attributing a result to a map. The guide describes an OS-modification save/close/reopen and initial write sequence; follow the current product's exact on-screen instructions, since an incorrect procedure can damage the controller. HP Tuners: L5P/L5D SOTF guide.

Logging an L5P

For an L5P/L5D log, a specialist describes loading the appropriate channel configuration and capturing the symptom, with a short baseline before testing. Configure the channels for the actual ECM, save the log and label the conditions; a full-throttle run is not necessary for every fault. DuramaxTuner logging procedure; HP Tuners channel setup.

Using the log to separate possibilities

At the point of a repeatable symptom, compare the available MAF signal with engine speed, driver demand/load and requested versus actual rail pressure; review recorded DTCs and the time trace rather than only average values. Inspect the intake, sensor and connections using the appropriate service information. A rail-pressure trace that looks normal does not prove the airflow signal is healthy. Transmission-slip indications are assessed separately.

An owner report illustrates this. A part-throttle stumble followed a change of turbo hardware; HP Tuners logs appeared to show actual rail pressure following the requested value, while misfires and torque-converter slip were also discussed. A suspected MAF signal problem was identified from the log, and a replacement MAF reportedly resolved the symptom. The truck's exact model year and the raw log were not independently verified, and this single owner-reported repair does not establish that every L5P stumble is a MAF fault. L5P owner discussion and follow-up.

Unresolved owner and tuner reports

An HP Tuners user on 2017-19 T87A trucks reported that changes to part-throttle shift tables did not produce the expected change and that normal and tow/haul logs differed; the user supplied OS 24285377 but no confirmed solution was reached. Compare mode, load, actual and commanded gear, speed and conditions in the actual truck; do not infer a universal table defect or copy another OS's values. 2017-19 T87A discussion.

Another L5P owner report describes an HP Tuners log and continuing P0191 rail-pressure problems after several parts were replaced, without establishing a final repair. It illustrates why an apparently normal short log or previous parts replacement should be assessed alongside the symptom, DTC conditions and manufacturer diagnostic tests rather than taken as proof of a particular fault.

Injector circuit evidence

GM bulletin 23-NA-027 covers specified 2017-23 Silverado/Sierra 2500HD and 3500HD L5P applications and describes injector-connector terminal wear associated with applicable misfire or injector-circuit codes. GM's PIP5582 describes grouped injector-driver behaviour for specified 2017-18 L5P trucks. Use the actual vehicle's VIN, market and current service information to check applicability. Multiple cylinder indications should be investigated at the circuit and driver level, not assumed to be simultaneous failed injectors.

Preserve diagnostic information and confirm sensor readings before making calibration changes or replacing parts. HP Tuners' Scanner configuration guidance explains how to select vehicle-specific channels. Tuning support and E41 service requirements vary by application; see the tool listing.